Table of Contents
Advertisement
USE ONLY FASTENERS THAT ARE RECOMMENDED FOR
YOUR MODELS.
Do not use the wrong fasteners or load
the fasteners incorrectly.
CHECK FOR MISALIGNMENT OR BINDING OF MOVING
PARTS, BREAKAGE OF PARTS, AND ANY OTHER
CONDITION THAT MAY AFFECT THE TOOL'S OPERATION.
If damaged, have the tool serviced before using. Many
accidents are caused by poorly maintained tools.
DO NOT USE TOOL IF TRIGGER DOES NOT ACTUATE
PROPERLY.
Any tool that cannot be controlled with the
trigger is dangerous and must be repaired.
NEVER USE TOOL WHICH IS DEFECTIVE OR OPERATING
ABNORMALLY.
If the tool appears to be operated
unusually, making strange noises, or otherwise appears
defective, stop using it immediately and arrange for
repairs by an authorized service center.
MAINTAIN TOOLS WITH CARE.
lubricated for better and safer performance.
NEVER CARRY THE TOOL BY AIR HOSE.
STORE TOOLS OUT OF THE REACH OF CHILDREN AND
OTHER UNTRAINED PEOPLE.
hands of untrained users.
PLACE TOOL PROPERLY ON WORKPIECE.
fasteners on top of other fasteners or with the tool at too
steep of an angle; the fasteners can ricochet and hurt
someone.
DO NOT USE THE TOOL AS A HAMMER.
KEEP ALL SCREWS AND COVERS TIGHTLY IN PLACE.
KEEP FACE, HANDS AND FEET AWAY FROM FIRING
HEAD AT ALL TIMES.
Never place your face, hands or
feet near the firing head.
DO NOT DISCONNECT AIR HOSE FROM TOOL WITH
FINGER ON TRIGGER.
connected to an air supply.
DO NOT LOAD FASTENERS WITH TRIGGER PULLED OR
SAFETY DEPRESSED.
NEVER PLACE A HAND OR ANY PART OF BODY IN
FASTENER DISCHARGE AREA OF TOOL.
DO NOT DRIVE FASTENERS INTO THIN BOARDS OR
NEAR CORNERS AND EDGES OF WORKPIECE.
fasteners can be driven or a way from the workpiece hit
someone.
DISCONNECT AIR HOSE FROM TOOL WHEN:
1). Doing maintenance and inspection;
2). Clearing a jam;
3). It is not in use;
4). Leaving work area;
5). Moving it to another location;
6). Handing it to another person.
Never attempt to clear a jam or repair the tool unless you
have disconnected air hose from the tool and removed
all remaining fasteners from the tool. The tool should
never be left unattended since people who are not
familiar with the tool might handle it and injure
themselves.
Keep the tool clean and
Tools are dangerous in the
Do not drive
The tool can fire when re-
TOOL SERVICE
USE ONLY ACCESSORIES THAT ARE IDENTIFIED BY THE
MANUFACTURER FOR THE SPECIFIC TOOL MODEL
USE OF UNAUTHORIZED PARTS OR FAILURE TO FOLLOW
MAINTENANCE INSTRUCTIONS MAY CREATE A RISK OF
INJURY
USE ONLY THE LUBRICANTS SUPPLIED WITH THE TOOL
OR SPECIFIED BY THE MANUFACTURE.
TOOL SERVICE MUST BE PERFORMED ONLY BY
QUALIFIED REPAIR PERSONNEL.
AIR SOURCE
NEVER USE OXYGEN OR OTHER BOTTLED GASES AS A
POWER SOURCE.
gases and other bottled gases are dangerous and may
cause the tool to explode.
DO NOT EXCEED MAXIMUM RECOMMENDED AIR
PRESSURE MARKED ON THE TOOL.
regulated, compressed air within the rated pressure
range marked on the tool. Never connect the tool to
pressure as which potentially exceeds 200PSI the tool
can burst.
DO NOT ABUSE THE AIR HOSE.
kinks, restrictions, solvents or sharp objects. Keep air
hose away from heat, oil, sharp edges or moving parts.
Replace damaged hoses immediately. Damaged hoses
can burst or whip around.
CHECK ALL FITTINGS, HOSES, PIPES, CONNECTIONS
AND COMPRESSOR BEFORE EACH USE OF THIS TOOL.
Repair or replace damaged or leaking hoses and
connections immediately. Damage to a hose or
connection can cause a pressure hose to break and whip
around the work area, and can lead to injury.
The
2
Explosion may occur. Combustible
Use only clean, dry,
Protect all hoses from
Advertisement
Table of Contents
