1. Manuals
  2. Brands
  3. Electrolux Manuals
  4. Ice Maker
  5. E15IM60EBS
  6. Installation manual

Electrolux E15IM60EBS Installation Manual

Electrolux e15im60ebs ice maker: installation guide
Hide thumbs Also See for E15IM60EBS:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Use and Care Manual
Installation

INSTALLATION DIMENSIONS

24"
14 - 15/16"
(61)
(37.9)
34 - 1/8"
(86.7)
FULL
RETRACT
5"
WATER
HEIGHT
(12.7)
VALVE
WATER
DRAIN
WATER
21 - 3/4"
OUTLET
(55.2)
Figure 1

Advertisement

Table of Contents
loading

Related Manuals for Electrolux E15IM60EBS

Summary of Contents for Electrolux E15IM60EBS

  • Page 1: Installation Dimensions

    Installation INSTALLATION DIMENSIONS 24” 14 - 15/16” (61) (37.9) 34 - 1/8” (86.7) FULL RETRACT 5” WATER HEIGHT (12.7) VALVE WATER DRAIN WATER 21 - 3/4” OUTLET (55.2) Figure 1...

  • Page 2: Drain Installation

    Model E15IM60E can be installed using a gravity drain or can use a factory installed or equivalent drain pump. Follow these guidelines when installing drain lines to prevent water from flowing back into the ice maker storage bin and/or potentially flowing onto the floor causing water damage: Gravity Drain •...
  • Page 3 WARNING WARNING Back panel serves as a guard. DO NOT put your hands inside the ice maker cabinet or attempt to touch any components except the discharge tube during testing. Failure to follow this warning could result in serious personal injury or death.

  • Page 4: Drain Pump Connection

    Electrolux EIMP60 drain pump. The Electrolux EIMP60 drain pump is available through your Dealer, or direct from Electrolux with complete installation instructions. If a pump other than the Electrolux EIMP60 drain pump is to be used, it must meet the following specifications: •...

  • Page 5: Site Preparation

    The unit must be located to allow clearance for water, drain and electrical connections in the rear of the ice maker. Connect the unit to a grounded and polarized 115 VAC, 60 Hz, 15 A circuit (normal household current).
  • Page 6 DOOR). All units require zero clearance when installed flush with a cabinet or wall (see Figure 4). Electrolux stainless steel models require a minimum 2-3/4 inch handle clearance when installed against a wall or cabinet that extends beyond the front edge of the unit (see Figure 5).

  • Page 7: Water Supply Connection

    Connect sufficient tubing to the unit to allow the unit to be moved for cleaning and servicing. However, make certain that the tubing is not pinched or damaged during installation. • Electrolux recommends the use of copper tubing for installation. WATER CONNECTION UL103_CO Figure 7...
  • Page 8 Water Supply Connection Locate the compression fitting and ferrule packed in the unit. Slide the compression fitting and ferrule over the 1/4 inch water supply line. Do not use thread sealing compound or tape. Using two wrenches, tighten the compression fitting on the supply line (see Figure 8). Carefully bend the water supply line into position and connect the line to the solenoid valve (see Figure 9).

  • Page 9: Leveling The Unit

    (see Figure 11). If the ice maker is not level, adjust the feet on the corners of the unit as necessary (see Figure 12). Check the levelness after each adjustment and repeat the previous steps until the unit is level.

  • Page 10: Door Reversal

    Door Reversal REVERSING THE DOOR (SOME MODELS) All Electrolux units may be left or right hand opening. The door opening is easily reversed by moving the hinge hard-ware to the opposite side (see Figure 13). To reverse the door: Figure 13...
  • Page 11 Remove top hinge (3 screws), reinstall hinge screw pin, and remount on opposite side BOTTOM (see Figure 17). Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge (see Figure 18). Remove existing bottom hinge (3 screws) and remount on opposite side TOP.

Table of Contents