White Outdoor 24AA570H190 Operator's Manual
  1. Manuals
  2. Brands
  3. White Outdoor Manuals
  4. Log Splitter
  5. 24AA570H190
  6. Operator's manual
White Outdoor 24AA570H190 Operator's Manual

White Outdoor 24AA570H190 Operator's Manual

Log splitter 27-ton
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATOR'S MANUAL
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning:
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-9722.
WHITE OUTDOOR PRODUCTS COMPANY P.O. BOX 361131 CLEVELAND, OHIO 44136-9722
PRINTED IN U.S.A.
ECO No.1481
Log Splitter
27-Ton
Model Number
24AA570H190
770-10017C.fm
FORM NO.
(5/00)

Advertisement

Table of Contents
loading

Related Manuals for White Outdoor 24AA570H190

Summary of Contents for White Outdoor 24AA570H190

  • Page 1 Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-9722. WHITE OUTDOOR PRODUCTS COMPANY P.O. BOX 361131 CLEVELAND, OHIO 44136-9722 770-10017C.fm PRINTED IN U.S.A.

  • Page 2: Table Of Contents

    A sample model plate is explained below. For future reference, please copy the model number and the serial number of the equipment in the space below. (Model Number) (Serial Number) Copy the model number here: WHITE OUTDOOR Copy the serial number here: PRODUCTS COMPANY P.O. BOX 361131 CLEVELAND, OHIO 44136...

  • Page 3: Important Safe Operation Practices

    SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.
  • Page 4 9. To avoid personal injury or property damage use 10. For logs which are not cut square, the least square extreme care in handling gasoline. Gasoline is end and the longest portion of the log should be extremely flammable and the vapors are explosive. placed toward the beam and wedge, and the Serious personal injury can occur when gasoline is square end placed toward the end plate.

  • Page 5: Assembling Your Log Splitter

    8. For your safety, replace all damaged or worn parts 9. Do not alter this machine in any manner, alterations immediately with original equipment such as attaching a rope or extension to the control manufacturer’s (O.E.M.) parts only. “Use of parts lever, or adding to the width or height of the wedge which do not meet the original equipment may result in personal injury.
  • Page 6 Assembling The Tongue • Insert hex bolt through the front hole of hitch and secure with flat washer and hex lock nut. Tighten Attaching The Beam Support/Latch Bracket (See Figure 1) both hex nuts to 23 ft-lbs. • Remove two hex bolts, lock washers, and hex nuts Tongue from the tongue.
  • Page 7 • Disconnect the pressure hose from the adapter on the pump. Lock • Stand the wedge, beam, and cylinder assembly Fender Washer upright with cylinder toward the top. NOTE: This step might require two people. • Remove cotter pin and clevis pin from welded brackets on beam assembly and move the Bolts reservoir tank assembly in position against the...
  • Page 8 Return Hose Carriage • The return hose is attached to the top of the control Cradles Bolts valve. Loosen the hose clamp on the free end of the hose. Cut the securing strap. Remove any protec- Cradle Support tive insert from the end of the hose. See Figure 8. Bracket •...

  • Page 9: Know Your Log Splitter

    • Refill tank to within 3” to 3 1/2” from the top of the fill tube. • Extend and retract the wedge 12 complete cycles to remove trapped air in the system (system is “self- bleeding”). • Refill the reservoir to within 3” to 3 1/2” from the top of the fill tube.

  • Page 10: Operating Your Log Splitter

    Starter Handle Stopping Engine The starter handle is located on the engine. Pull the • Move throttle control lever to STOP or OFF starter handle to start engine. position. Engine Controls • Disconnect spark plug wire and ground against the See the separate engine manual for the location and engine to prevent unintended starting.

  • Page 11: Adjusting Your Log Splitter

    Horizontal Position • Place the log against the end plate and only split wood in the direction of the grain. • Pull the vertical beam lock out and pivot it down. • When necessary to stabilize the log, place your Pivot the beam to the horizontal position.

  • Page 12: Maintaining Your Log Splitter

    Gib Plate Adjustment Attached To Cylinder Periodically remove and replace the “gibs” (spacers) between the wedge plate and the back plate. See Figure 15. Bolts NOTE: The gibs may be rotated and/or turned over for even wear. • Remove the center bolt on top of the wedge plate. Slide the gib plate out.
  • Page 13 When replacing the flexible pump coupler, proceed as • Set .010” to .060” clearance between the nylon follows: “spider” and the engine coupling half by sliding a matchbook cover between the nylon “spider” and • Remove three nuts and lock washers that secure the engine coupling half and moving pump coupling the pump to the coupling shield.

  • Page 14: Conditions That Will Void Warranty

    SECTION 7: CONDITIONS THAT WILL VOID WARRANTY • Failure to maintain proper fluid level in reservoir will • Improper beam lubrication will cause premature cause permanent damage to pump by allowing air wear and looseness. Lubricate the beam regularly. to be drawn into pump. Fluid will become foamy. Lack of lubrication will void your warranty.
  • Page 15 SECTION 9: HYDRAULIC TROUBLESHOOTING Problem Cause Remedy Cylinder rod will not move 1. Broken drive shaft. 1. See authorized service dealer. 2. Shipping plugs left in hydraulic 2. Disconnect hydraulic hoses, remove hoses. shipping plugs, reconnect hoses. 3. Set screws in coupling not adjusted 3.

  • Page 16: Parts List

    Model Number 24AA570H190 62 63 65 66...
  • Page 17 Model Number 24AA570H190 Ref. Ref. Part No. Part Description Part No. Part Description 781-0323B Wedge Assembly 710-1338 Hex Screw 5/16-24 x 3.25 712-0239 Lock Nut 1/2-20 714-0122 Square Key 3/16” x .75 710-1018 Hex Cap Screw 1/2-20 x 2.75 718-0686...
  • Page 18 NOTES...
  • Page 20 Products Co. with respect to new merchandise pur- d. White Outdoor Co. does not extend any warranty for chased and used in the United States, its possessions and products sold or exported outside of the United States territories.

Table of Contents