Download
Share
Print this page
  1. Manuals
  2. Brands
  3. ClearSpan Manuals
  4. Greenhouse Kit
  5. 108986
  6. Manual

ClearSpan 108986 Manual

End frame kit 36' wide x 16' 2" high
Hide thumbs

Advertisement

Quick Links

Download this manual
Rafter is not included with kit. Customer supplies the concrete to secure the 2" x 2" tubing.
©2014 ClearSpan™
All Rights Reserved. Reproduction
is prohibited without permission.
Revision date: 11.12.14
ClearSpan
End Frame Kit
™
36' Wide x 16' 2" High
CLEARSPAN
END WALL FRAMING KITS
™
STK#
108986
End Frame Kit
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the 108986 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ClearSpan 108986

Summary of Contents for ClearSpan 108986

  • Page 1 ClearSpan End Frame Kit ™ 36' Wide x 16' 2" High Rafter is not included with kit. Customer supplies the concrete to secure the 2" x 2" tubing. ©2014 ClearSpan™ All Rights Reserved. Reproduction is prohibited without permission. STK# 108986 End Frame Kit Revision date: 11.12.14...

  • Page 2: Safety Precautions

    BEGIN TO ASSEMBLE THE END WALL KIT. before you begin assembling the end wall. Thank you for purchasing this ClearSpan™ End Frame Kit. 3. Gather the tools, bracing, ladders (and lifts), and When properly assembled and maintained, this product will assistance needed to assemble the end frame.
  • Page 3 CLEARSPAN END WALL FRAMING KITS ™ UNPACK AND IDENTIFY PARTS The following graphics and photos will help you identify the different parts. (Some parts are not shown.) The following steps will ensure that you have all the necessary parts before you begin to assemble the end wall.
  • Page 4 CLEARSPAN END WALL FRAMING KITS ™ ClearSpan™ End Frame Kit ATTENTION: End frame spacing depends on the door sizes and may differ from what is shown in these diagrams. Consult OVERVIEW the End Wall diagrams in the Quick Start section for pipe This section describes assembling your end frame identifications and locations.
  • Page 5 CLEARSPAN END WALL FRAMING KITS ™ ASSEMBLING THE END FRAME KIT COMPONENTS Sample Frame Consult the end wall diagrams in the Quick Start section of these instructions before you begin. ATTENTION: If the main cover is installed, loosen the two (2) main cover bonnet ratchets at the end of the shelter where the end wall will be installed.
  • Page 6 CLEARSPAN END WALL FRAMING KITS ™ INSTALL THE END FRAME (CONTINUED) 5. Plumb the vertical frame tube and use wooden stakes or other means to anchor it in place. 6. Repeat the steps to construct, attach, and set the remaining end frame tubes.
  • Page 7 CLEARSPAN END WALL FRAMING KITS ™ END PANEL INSTALLATION 3. With the temporary straps (or customer-supplied rope) in place, pull the end panel up to the end rafter and The following procedure describes installing an end panel secure the end panel to the end rafter using small that includes D-rings at the top and horizontal pocket heat sections of the strap.
  • Page 8 CLEARSPAN END WALL FRAMING KITS ™ END PANEL INSTALLATION (CONTINUED) 4. Once the end panel is temporarily secured, take the roll Space below is reserved for customer notes. of 1" strapping and weave the end of the strap through the D-rings and around the rafter pipe as shown below.
  • Page 9 CLEARSPAN END WALL FRAMING KITS ™ END PANEL INSTALLATION (continued) 5. Once ratchets are attached, make a horizontal slit (approximately 3"– 6" long) in the horizontal pocket Install Horizontal End Panel Conduit directly above each ratchet. See photos for details.

  • Page 10: End Panel

    CLEARSPAN END WALL FRAMING KITS ™ END PANEL INSTALLATION (continued) Cut Door Openings (Door installation only; additional door purchase required.) ATTENTION: For best results and to keep the stretched panel in position, install Tek screws and washers from the outside around the door frame to secure the end panel to the door jambs and header.
  • Page 11 CLEARSPAN END WALL FRAMING KITS ™ Secure the End Panel to the End Frame The frame shown in the following diagrams may differ from the actual frame. Installation steps are the same. 1. With door openings cut, secure the end panel to the door frame using Tek screws and washers. See diagram below.
  • Page 12 CLEARSPAN END WALL FRAMING KITS ™ INSTALL THE END RATCHETS FOR THE MAIN COVER Main Cover After end panel is fully stretched and all doors are installed Bonnet (if equipped), reattach end ratchets for main cover bonnet. May not apply to some shelters and end panels.
  • Page 13 CLEARSPAN END WALL FRAMING KITS ™ SHELTER CARE AND MAINTENANCE Proper care and maintenance of your ClearSpan™ product Space below is reserved for customer notes. is important. Check the following items periodically to properly maintain your building and end frame: •...
  • Page 14 CLEARSPAN END WALL FRAMING KITS ™ QUICK START GUIDE 36' W x 16'-2" H End Frame Kit The end frame kit does not include the end rafter or end panel as shown in the diagram below. Customer-supplied Ground Level Concrete Pier End frame shown may differ from the actual end frame.
  • Page 15 CLEARSPAN END WALL FRAMING KITS ™ Revision date: 11.12.14...
  • Page 16 CLEARSPAN END WALL FRAMING KITS ™ Revision date: 11.12.14...
  • Page 17 CLEARSPAN END WALL FRAMING KITS ™ DOOR FRAME DIAGRAM: SPECIAL NOTES* Doors are not included with the end frame kit. Additional purchase is required. ATTENTION: For some doors, the upper brackets are mounted wider than the actual door frame. In those instances, cut a 16"...