Table of Contents
Advertisement
Quick Links
Regency Horizon
www.regency-fire.com
WARNING:
If the information in these instructions
are not followed exactly, a fire or
explosion may result causing property
damage, personal injury or loss of life.
WARNING: For Outdoor Use Only.
Installation and service must be
performed by a qualified installer,
service agency, or the gas supplier.
WARNING:
Do not store or use gasoline, or other flammable vapors and liquids, in the vicinity of this or any
other appliance.
An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
Tested by:
920-274a
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
HZO42 Outdoor
®
Gas Fireplace
If you smell gas:
• Shut off gas to the appliance.
• Extinguish any open flame.
• If odour continues, leave the area immediately.
• After leaving the area, call your gas supplier or fire
department.
Failure to follow these instructions could result in fire or
explosion, which could cause property damage, personal
injury, or death.
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
DANGER - FIRE OR EXPLOSION HAZARD
Owners &
Installation Manual
MODELS: HZO42-NG11
HZO42-LP11
HZO42 Product Video
10.18.21
Advertisement
Table of Contents
Related Manuals for Regency Fireplace Products Horizon HZO42
Summary of Contents for Regency Fireplace Products Horizon HZO42
- Page 1 Owners & Regency Horizon HZO42 Outdoor ® Installation Manual Gas Fireplace MODELS: HZO42-NG11 HZO42-LP11 www.regency-fire.com HZO42 Product Video WARNING: DANGER - FIRE OR EXPLOSION HAZARD If the information in these instructions If you smell gas: are not followed exactly, a fire or •...
- Page 2 Class IIIA marking Size@ 100% - 6”H x 2.7”W Black font on silver background Apr. 27/17: Created draft Horizon HZO42 Product Video May 8/20: Rev A. Wording changed WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property dam- age.
-
Page 3: Table Of Contents
table of contents safety label Nailing Strips............17 Drain Installation (recommended) .......18 Wall Switch and Battery Installation ......19 Copy of Safety Decal .............4 Wiring Diagram ............20 Decal Location ...............4 Hardwire Kit Installation ..........21 AC Adaptor Installation ..........25 dimensions Inner Panel Installation ..........26 Glass Crystal Installation ..........27 Unit Dimensions ............5 Volcanic Stone Installation ..........28... -
Page 4: Copy Of Safety Decal
safety decal This is a copy of the label that accompanies each HZO42 Outdoor Fireplace. We have printed a copy of the contents here for your review. NOTE: Regency ® units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one. COPY OF SAFETY DECAL For the State of Massachusetts, installation and repair must be done by a plumber or gas fitter... -
Page 5: Unit Dimensions
dimensions UNIT DIMENSIONS Note: Gas Connection/Electrical connections if using optional Hardwire Kit are located on left hand side of appliance. ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY. ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS. Regency Horizon®... -
Page 6: Gas Installation Checklist
dimensions GAS INSTALLATION CHECKLIST REGENCY GAS INSTALLATION CHECKLIST This general checklist does not contain all pertinent installation details or specifics and does not supersede the guidelines in this manual. Your Regency dealer/installer should use it in conjunction with manual instructions. Please follow all local codes and jurisdictions in authority. Customer: Date Installed: Install Address:... - Page 7 installation REGENCY GAS INSTALLATION CHECKLIST Finishing If applicable, is only noncombustible material installed in the noncombustible areas? Do clearances meet installation and manual requirements? Do the mantels and/or projections comply with the installation manual? If applicable, was the solid fuel fireplace warning plate installed? Appliance Media Setup Do commands from the remote or wall switch light the pilot and main burner? Are the burner media/log set, glass door, and screen installed per instructions in the manual?
-
Page 8: Important Message
installation IMPORTANT MESSAGE 3. See general construction and assembly instruc- DO NOT USE THIS APPLIANCE IF tions. The appliance should be enclosed. SAVE THESE INSTRUCTIONS ANY PART HAS BEEN UNDER WATER. IMMEDIATELY CALL A QUALIFIED 4. Inspect the burner before each use of the appli- The HZO42-11 Gas Fireplace must be installed in ance for blockage and any signs of deterioration. -
Page 9: Installation Checklist
installation LOCATING YOUR INSTALLATION GAS FIREPLACE CHECKLIST 1) Locate appliance: 1) When selecting a location for your fireplace, ensure that the clearances are met. a) Refer to "Locating Your Gas fireplace" section 2) This appliance must be installed in an open-air situation with natural ventilation, without stagnant b) Clearances to Combustibles (Refer to areas, where gas leakage and products of combustion are rapidly dispersed by wind and natural "Clearances"... -
Page 10: Outdoor Appliance Installation Summary
installation IMPORTANT INFORMATION FOR OUTDOOR FIREPLACE INSTALLATIONS IMPORTANT THINGS TO REMEMBER • Never insulate around the body of the unit • Excessive heat retention in the firebox will lead to component failure • Correct Working Gas pressure is critical on “E” units and fireplace malfunction •... -
Page 11: Minimum Clearances To Combustibles
installation MINIMUM CLEARANCES TO COMBUSTIBLES The clearances listed below are minimum distances unless otherwise stated. A major cause of fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this fireplace be installed only in accordance with these instructions. WARNING Caution Requirements Fire hazard is an extreme risk... -
Page 12: Framing Dimensions
installation FRAMING DIMENSIONS Framing Description HZO42-11 Dimensions Header Height 32-11/16” (30mm) Side Stud Width 42 - 3/16" (1072mm) Minimum framing depth 20" (508mm) Minimum Height to Combustibles 52 - 1/2" (1334mm) Minimum framing width 60" (1524mm) Corner Wall Depth 40 - 7/16" (1027mm) Corner Facing Wall Width 54 - 3/16"... -
Page 13: Mantel Clearances
installation MANTEL CLEARANCES Due to the extreme heat this fireplace emits, the mantel clearances are critical. Combustible mantel clearances from 12" (305mm) top of front facing are shown in the diagram on the right. Combustible Material Note: Ensure the paint that is used on the mantel and the facing is "heat resistant"... -
Page 14: Hzo42 Enclosure Vent Installation
installation HZO42 ENCLOSURE VENT INSTALLATION Four (4) ventilation grills are required for all enclosures. Two (2) upper and two (2) lower ventilation grills are required for all enclosures. This is to alleviate moisture and allow for air to circulate. Minimum recommended size: 20" sq. (508 mm²) ea. If using the grills offered by Regency (supplied), follow the instructions noted below: Frame the opening for the upper vent (377-060) at 16"... -
Page 15: Finishing
installation FINISHING IMPORTANT FINISHING DETAIL NOTE: Before placing unit into final position - it is important to know the total thickness / height of finished hearth. The base of the fireplace should be level or higher than the finished hearth height. If material such as brick, stone, etc extends past the faceplate depth (1-1/2"), when finishing around the faceplate, the minimum opening dimensions noted below must be adhered to ensuring for the removal of the faceplate and for the safe operation of this appliance. -
Page 16: High Elevation
installation HZO42-NG11 SYSTEM DATA Burner 880 S.I.T. VALVE Max. Supply Pressure 14" WC (3.49 kPa) DESCRIPTION Flame Sensor Min. Supply Pressure 5" WC (1.25 kPa) Manifold Pressure 3.5" WC (0.87 kPa) 1) Pilot adjustment Orifice Size #29 DMS 2) Outlet Pressure Tap Maximum Input 44,500 Btu/h Pilot... -
Page 17: Unit Assembly Prior To Installation
installation UNIT ASSEMBLY PRIOR TO INSTALLATION NAILING STRIPS The 6 Standoffs must be correctly positioned and attached before unit is slid into position. The nailing strips come attached to the unit. There is 1 plate on each side and 1 on the top that can be folded out as required. Secure the top and side nailing strips to the framing. -
Page 18: Drain Installation (Recommended)
installation DRAIN INSTALLATION (RECOMMENDED) Although this fireplace is designed to operate outdoors safely, rain and other sources of moisture may enter the hearth area, which will cause water to col- lect inside the base of the unit. To prevent excessive water collection, the installer must provide a way to drain the water from the base of the unit by building or installing a water collector before positioning the fireplace in its location. -
Page 19: Wall Switch And Battery Installation
installation WALL SWITCH AND BATTERY INSTALLATION (INCLUDED WITH UNIT) The unit comes with low voltage wire and a battery extension wire installed. 6) Install supplied 4-AA batteries into the battery holder. Using velcro install battery holder to the backside of the battery compartment door. Connect 1) Run supplied wire to desired location - to a max. -
Page 20: Wiring Diagram
installation WIRING DIAGRAM This heater does not require a 120V A.C. supply for operation. (Do not cut the ground terminal off under any circumstances.) NOTE: 4 AA batteries must be installed in the battery pack to operate the burner switch. Proflame SureFire™... -
Page 21: Hardwire Kit Installation
OUTDOOR SERIES installation OPTIONAL HARD WIRE KIT INSTALLATION HARDWIRE KIT INSTALLATION A hard wire kit is available for this unit as an option, to hard wire this appliance, a qualified electrician must remove the cord connection, and wire the appliance directly to the household wiring. This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. - Page 22 OUTDOOR SERIES installation 5. Plug in the supplied AC adaptor and run the wire through the bottom 10. HZO42/HZO60--Remove the burner tray by lifting up and out. of the outer box, be sure to use a grommet to protect the wire. 6.
- Page 23 OUTDOOR SERIES installation WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this ap- pliance may result in property damage or personal injury. 919-774 04.03.17 Regency Horizon® HZO42 Gas Fireplace...
- Page 24 installation OUTDOOR SERIES PTO50/PTO30/HZO42 WIRING DIAGRAM USING AC ADAPTOR 0.886.001 Proflame Valve Standard Main On/Off Switch or Optional Wall Switch 0.584.302 (PTO30) 0.584.622 (PTO50/HZO42) Proflame DFC Board PTO100/PTO60 WIRING DIAGRAM (2 X PTO50 / 2 X PTO30 ASSEMBLED END-TO-END) USING AC ADAPTOR Battery Holder ON/OFF Switch 919-774...
-
Page 25: Ac Adaptor Installation
installation OUTDOOR SERIES AC ADAPTOR INSTALLATION AC ADAPTOR INSTALLATION A hard wire kit is available for this unit as an option (see hard wire kit instructions), to hard wire this appliance, a qualified electrician must remove the cord connection, and wire the appliance directly to the household wiring. This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. -
Page 26: Inner Panel Installation
HZO42/HZO42-11 installation PANEL INSTALLATION INNER PANEL INSTALLATION Before installation, panels must be handled and cleaned as per instructions noted below: Stainless Steel Panels • Stainless panels must be inspected for scratches and dimples prior to installation. All claims to be recorded at this time. Claims for damage after installation will not receive consideration. -
Page 27: Glass Crystal Installation
installation GLASS CRYSTAL INSTALLATION Spread the Glass Crystals or Stones evenly over the burner. Ensure the crystals/stones do not overlap excessively as this will affect the flame pattern. IMPORTANT NOTE: Only the approved Glass Crystals and Stones are to be used with these fireplaces. Use of any other type of glass crystals or stones can alter the unit's performance, any damage caused by the use of any unapproved glass or stones will not be covered under warranty. -
Page 28: Volcanic Stone Installation
installation OPTIONAL VOLCANIC/GARDEN STONES INSTALLATION ON BURNER VOLCANIC STONE INSTALLATION Evenly spread the glass crystals and volcanic stones over the burner. Ensure the stones do not overlap too much as this will effect the flame pattern. IMPORTANT NOTE: Only the supplied approved Volcanic Stones are to be used with these fireplaces. Use of any other type of stones can alter the unit's performance, any damage caused by the use of any unapproved glass or stones will not be covered under warranty. -
Page 29: Optional Log Set Installation
HZO42/HZO42-11 installation OPTIONAL LOG SET INSTALLATION LOG/TWIG SET INSTALLATION Installation of Reflective Panels must be completed before installing the log set. Installation of Reflective Panels (if installing) must be completed before installing the Log/Twig set. Read the instructions below carefully and refer to the images. If the logs are broken do not use the unit until they are replaced. - Page 30 installation HZO42/HZO42-11 4) Install Log D on the burner as shown below. Orient Log D across Log E in the same way and in a similar position as depicted in Diagram 5- Log D will rest up against the back panel. Diagram 5 5) Install Log F on the right side of the burner as shown below.
-
Page 31: Heat Deflector Installation
installation HEAT DEFLECTOR INSTALLATION 1) Install the heat deflector to the top inside of the firebox with 4 screws as shown below. Heat Deflector Heat Deflector Installed Regency Horizon® HZO42 Gas Fireplace... -
Page 32: Faceplate Installation
installation FACEPLATE INSTALLATION Remove the protective coating from the faceplate before installation - see For installations where thicker finishing material is used - the optional handling instructions in panel install section. trim piece may be installed to fill the gap. Install the trim between the bottom access panel and the faceplate as To install the faceplate - line up the tabs on the faceplate with the 'C' shown below. -
Page 33: Glass Wind Shield Installation
installation GLASS WIND SHIELD INSTALLATION 1) To install the glass wind shield - slot it into the space between the burner tray cover and the bottom access panel. Burner Tray Cover Glass Wind Shield Bottom Access Panel WEATHER COVER INSTALLATION / REMOVAL 1) The unit should be covered when not in use for extended periods of time. - Page 34 OUTDOOR 42 installation ASSEMBLY INSTRUCTIONS FOR A STEEL STUD FRAMING KIT FOR HZO42 ASSEMBLY INSTRUCTIONS FOR A STEEL STUD FRAMING KIT FOR OUTDOOR 42 Follow these instructions to construct a steel stud frame for the Outdoor fi replace; Overall dimensions = 60" W x 20" D x 52-1/2" H. **Non-combustible fi...
- Page 35 OUTDOOR 42 installation 1) Place top/bottom (A) on the ground - fl at side down. Bend 3) Line up the screw holes of (A) with (B). Secure the tabs up to a 90° angle. each (B) with 2 wafer screws (one on each side) as shown below.
- Page 36 OUTDOOR 42 installation 6) Manoeuvre remaining (B) pieces and position in each corner 9) Position remaining 2 - (C) pieces offset from center rib as of the frame - fl at side facing out - see 2 diagrams below. shown below. 10) Position (D) on top of (C) pieces - line up screw holes and secure (D) to (C) with 12 wafer screws.
- Page 37 OUTDOOR 42 installation 12) LIne up screw holes on (E) (header) and (B) (inner vertical 14) Line screw holes on 1 (F) (corner brace) with (B) + (A) and support). Secure with 2 wafer screws on each side (4 total) secure with 4 wafer screws.
-
Page 38: Operating Instructions
operating instructions OPERATING FIRST FIRE INSTRUCTIONS The first fire in your fireplace is part of the paint curing process. To ensure that the paint is properly 1) Read and understand these instructions before cured, it is recommended that you burn your fireplace operating this appliance. -
Page 39: Copy Of Lighting Plate Instructions
operating instructions COPY OF LIGHTING PLATE INSTRUCTIONS The lighting plate is located on the underside of the front access panel in the unit. Regency Horizon® HZO42 Gas Fireplace... -
Page 40: Maintenance Instructions
maintenance MAINTENANCE INSTRUCTIONS 1. Always turn off the gas valve and unplug the batteries before cleaning. For relighting, refer to lighting instructions. Keep the burner and control compart- ment clean by brushing and vacuuming at least once a year. When cleaning the logs, use a soft clean paint brush as the logs are fragile and easily dam- aged. -
Page 41: Valve Assembly Replacement
maintenance VALVE ASSEMBLY REPLACEMENT 1. Turn the unit off and allow it to cool down to room temperature. 9. Remove the front access panel by lifting up and out. 2. Turn off the gas supply to the unit. 3. Remove trim. 4. - Page 42 maintenance 12) Slide the burner to the right and lift up and out of the firebox. 13) Remove 6 screws in locations shown below to access DFC. 6th screw located at back 14) Remove 6 screws and lift out valve tray. 15) Replace with new valve tray and reverse steps.
-
Page 43: Digital Fireplace Burner Control Removal
maintenance DIGITAL FIREPLACE BURNER CONTROL REMOVAL 4. Disconnect the Black sparker wire with black spade connector from CN3. 1. Remove 6 screws in locations shown below to access DFC. See Diagram 2 below. 6th screw located at back Diagram 2 Sparker Wire 5. -
Page 44: Gas Maintenance
maintenance Gas Maintenance GAS MAINTENANCE - RECOMMENDED ANNUAL ROUTINE Recommended Annual Routine Maintenance for Gas Fireplaces, Stoves and Inserts In order for your Regency appliance to continue to provide comfort to your home periodic maintenance must be performed to ensure it is operating at peak efficiency. The items in the list should be checked by a licensed gas service technician during the annual service check. Your unit may require more frequent maintenance checks if you notice any changes in how it operates. Operational changes to look for can include, but are not limited to, extended start up time, increased fan noise, residue/carbon build up, white build up on the glass/firebox, increased operating noise etc. Should any of these or other conditions arise, discontinue use and schedule a service check with your local licensed gas technician. The list below shows items your licensed service technician will need to check and service at least annually. Clean Inspect Check • Glass • Pilot assembly • Voltage on thermocouple/thermopile (mil- • Interior bricks / panels • Burner livolt models) • Burner ports & burner air shutter •... -
Page 45: Main Assembly
parts list MAIN ASSEMBLY Part # Description Part # Description 326-036 Top nailing strip 326-552 2" Faceplate assembly 326-037/F Side nailing strip 326-009 Heat Deflector 910-533/P Glass Windshield (Each) 326-066 Filler Trim 948-223 Regency Logo Plate 911-265 (DFC) Digital Fireplace Control 326-038 Clip Glass (Brushed SS) (Each) 910-363... -
Page 46: Burner Assembly
parts list BURNER ASSEMBLY Part # Description Part # Description 326-525 Burner Assembly NG-LP 14) 904-777 Burner Orifice #29 NG 904-434 Burner Orifice #47 LP 10) 327-574/P Valve Assembly - NG 10) 327-576/P Valve Assembly - LP 326-028 Pilot Shield N/S 910-036 Pilot Orifice - NG N/S 910-101... -
Page 47: Accessories
parts list ACCESSORIES Part # Description 326-021 Panel Rear (Brushed Stainless) Part # Description 326-022 Panel Left (Brushed Stainless) 326-023 Panel Right (Brushed Stainless) 946-675 Black Glass Crystals (1 Pound) 326-552 Faceplate Brushed Stainless 946-676 Copper Glass Crystals (1 Pound) 946-677 Starfire Glass Crystals (1 Pound) 326-034... -
Page 48: Warranty
warranty Limited Warranty FPI Fireplace Products International Ltd. (for Canadian customers) and Fireplace Products U.S., Inc. (for U.S. customers) (collectively referred to herein as “FPI”) extends this Limited Warranty to the original purchaser of this appliance provided the product remains in the original place of installation. The items covered by this limited warranty and the period of such coverage is set forth in the table below. - Page 49 warranty Replacement units are limited to one per warranty term. Unit must be installed according to all manufacturers’ instructions as per the manual. All Local and National required codes must be met. The installer is responsible to ensure the unit is operating as designed at the time of installation. The original purchaser is responsible for annual maintenance of the unit, as outlined in the owner’s manual.
- Page 50 warranty Limitations of Liability: The original purchaser’s exclusive remedy under this warranty, and FPI’s sole obligation under this warranty, express or implied, in contract or in tort, shall be limited to replacement, repair, or refund, as outlined above. IN NO EVENT WILL FPI BE LIABLE UNDER THIS WARRANTY FOR ANY INCIDENTAL OR CONSEQUENTIAL COMMERCIAL DAMAGES OR DAMAGES TO PROPERTY.
- Page 51 warranty Product Registration and Customer Support: Thank you for choosing a Regency Fireplace. Regency strives to be a world leader in the design, manufacture, and marketing of hearth products. To provide the best support for your product, we request that you complete a product registration form found on our Web Site under Customer Care within ninety (90) days of purchase.
- Page 53 notes Regency Horizon® HZO42 Gas Fireplace...
- Page 54 notes 54 | Regency Horizon® HZO42 Gas Fireplace...
- Page 56 ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial #: ____________________________________________________________ Horizon HZO42 Product Video Printed in Canada Regency Horizon is a trademark of FPI Fireplace Products International Ltd. ® © Copyright 2021, FPI Fireplace Products International Ltd. All rights reserved.