Table of Contents
Advertisement
Available languages
Available languages
ENGlIsh
•
An extension cord must have adequate wire size
for safety. The smaller the gauge number of the wire,
the greater the capacity of the cable, that is, 16 gauge
has more capacity than 18 gauge. An undersized cord
will cause a drop in line voltage resulting in loss of power
and overheating. When using more than one extension
to make up the total length, be sure each individual
extension contains at least the minimum wire size. The
following table shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt, use
the next heavier gauge. The lower the gauge number, the
heavier the cord.
Voltage
Total length of cord in meters (m)
(Volts)
120–127V
0–7
220–240V
0–15
Rated
Minimal cross-sectional area of the
ampere
cord in meters (mm
Range
0–6A
1.0
6–10A
1.0
10–12A
1.5
12–16A
2.5
WARNING: If the plug or power cord is damaged,
it must be replaced by the manufacturer or its
representative or by an equally qualified person to
avoid danger.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. D
if this tool does not operate, check power supply.
20
7–15
15–30
30–50
15–30
30–60
60–100
)
2
1.5
1.5
2.5
1.5
2.5
4.0
1.5
2.5
4.0
4.0
Not Recommended
or AC ........... alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n
........................ no load speed
o
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
WALT tools are factory tested;
e
spECIFICaTIoNs
Tool Holder
Amps
Impact Energy in Joules (EPTA)
No-Load BPM
Weight
Length
Width
Height
Vibration Control
Variable Speed Dial
Variable Speed Dial Positions
Dust Extraction Model #
Noise Values [dB(A)]
L
(Emission Sound Pressure Level)
pA
L
(Sound Power Level)
WA
K (Uncertainty of Given Sound Level)
Vibration Values (m/s
2
)
Chipping/Chiselling (Value a
h,Cheq
Uncertainty K
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Bail/Loop Style Auxiliary Handle (Fig. B)
WARNING: To reduce the risk of personal injury,
ALWAYS operate the tool with the bail/loop style
auxiliary handle properly installed. Failure to do so
may result in the bail/loop style auxiliary handle
slipping during tool operation and subsequent
loss of control. Hold tool with both hands to
maximize control.
The bail/loop style auxiliary handle
the gear case and may be rotated 360˚ to permit right- or
left-hand use.
Mounting the Bail/Loop Style Auxiliary
Handle (Fig. B)
1. Widen the ring opening
auxiliary handle
2
by rotating the screw for handle
mounting
12
counterclockwise.
2. Slide the assembly onto the nose of the tool, through
the steel ring
and onto the collar
11
holder and sleeve.
D25832
SDS MAX
14 A
7,7 ft/lbs (10,5 J)
1450–2900
16.2 lbs.
(7.4 kg)
20.5" (52.1 cm)
4.4" (11.2 cm)
11.5" (29.3 cm)
®
SHOCKS
Yes
7
DWH053
95
106
3
)
8.7
1.5
clamps to the front of
2
11
of the bail/loop style
, past the chisel
3
Advertisement
Table of Contents
