Related Manuals for Toro Wheel Horse 78200
Summary of Contents for Toro Wheel Horse 78200
- Page 1 Form No. 3327–580 Rev A Quiet Collector Wheel Horse Lawn and Garden Tractor Attachment Model No. 78200—Serial No. 220000001 and Up Operator’s Manual English (GB)
-
Page 2: Table Of Contents
Toro products and other safety information you must know. additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 illustrates the location of the model and serial numbers on the product. -
Page 3: Safety
Safety The following list contains safety information specific to Toro products and other safety information you must know. Become familiar with the safe operation of the equipment ant with the operator controls, and safety signs. Use extra care with grass catchers or other attachments. -
Page 4: Safety And Instruction Decals
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 106-2655 1. Warning—do not touch or approach moving belts; remove the ignition key and read the instructions before servicing or performing maintenance. -
Page 5: Setup
Setup Note: Determine the left and right sides of the machine from the normal operating position. Loose Parts Note: Use the chart below to verify all parts have been shipped. DESCRIPTION QTY. Quick hitch Tow hitch extension Locknut, 1/2 in. Installing the quick hitch Locknut, 3/8 in. -
Page 6: Installing The Quick Hitch
DESCRIPTION QTY. Upper tube Middle tube Boot Carriage bolt, 1/4 x 3/4 in. Installing the discharge tubes Flange nut, 1/4 in. Hairpin cotter pin Decal Installing the decal Operator’s manual Read before operation Installing the Quick Hitch 1. Raise the rear of the tractor and support with jack stands. -
Page 7: Installing The Collector Drive
m-5950 m–5966 Figure 5 Figure 3 1. Bolt, 1/4 x 1 in. 4. Locknut, 5/16 in. 1. Carriage bolt, 3/8 x 1 in. 4. Lock nut, 1/2 in. 2. Carriage Bolt, 5/16 x 1 in. 5. Jack shaft 2. Lock nut, 3/8 in. 5. -
Page 8: Installing The Collector
Installing the Collector 1. Align the hinges on both halves of the collector. The halves must be positioned in the closed position (Fig. 9). 2. Push the dumping arm through the hinges and secure with a cotter pin (3/16 x 1 in.) (Fig. 9). m-5959 Figure 7 1. -
Page 9: Installing The Mower
8. Secure left side hitch hook with a clevis pin (3/8 x 4. Center punch the 2 holes that are to be drilled and 1–1/2 in.) and a hairpin cotter (Fig. 11). remove the template (Fig. 12). 9. Install the collector belt onto the the jack shaft pulley 5. -
Page 10: Installing The Discharge Tubes
Note: Install the bolt heads on top of the mower. 7. Install the belt guard (Fig. 13). m-5962 Figure 14 1. Boot 5. Boot bracket 2. Boot Pin 6. Bolt, 1/4 x 1/2 in. and flange nut, 1/2 in. 3. Hairpin cotter pin 7. -
Page 11: Installing The Decal
Operation Note: Determine the left and right side of the machine from the normal operating position. Warning To avoid personal injury, follow these procedures: Become familiar with all operating and safety m-5957 instructions in the operator’s manual for your Figure 16 mower before using this attachment. -
Page 12: Holding The Collector Door Open
4. Raise the collector arm to the highest position and 3. Stop the engine, remove the key, and wait for all release the collector lever (Fig. 18). The locking pin moving parts to stop before leaving the operating will drop into a hole in the highest position. position. -
Page 13: Clearing Obstructions From The Collector
A. Raise the gauge arm frequently (Fig. 21). If you feel resistance, it indicates the collector is full and needs to be emptied. B. If grass is seen building up in the slots, on top of the boot (Fig. 14), the collector is full and needs to be emptied. -
Page 14: Removing The Collector
Cutting Technique Also, grass may be seen building up inside the slot on top of the boot. For best lawn appearance, be sure to slightly overlap the mower into the previously cut area. This helps reduce the Removing the Collector load on the engine and reduces the chance of plugging the blower and discharge tube. -
Page 15: Maintenance
Maintenance Note: Determine the left and right side of the machine from the normal operating position. Recommended Maintenance Schedule Maintenance Service Maintenance Procedure Interval Each Use Screen—clean 10 Hours Collector—clean Collector—check belt tension Collector—inspect 40 Hours Collector idler arms—oil/lubricate Collector idler arms—oil/lubricate Belts—check for wear/cracks Storage Service Collector—belt tension... -
Page 16: Troubleshooting
5. Store the machine in a clean, dry place, out of direct sunlight. This protects the plastic parts and extends the life of the machine. If you must store the machine outside, cover it with a weatherproof cover. Troubleshooting Problem Possible Causes Corrective Action Abnormal vibration. - Page 18 Cut out template here Template No. 1 Existing Hole 42 in. (107 cm) mower Existing Hole template Drill a 9/32 in. hole here. Towards Side Discharge Drill a 9/32 in. hole here. Cut out template here Scale Template No. 1 1 inch 26 mm...
- Page 20 Align this edge with the re– Cut out template here enforcing plate on top of the mower Drill a 9/32 in. hole here. Drill a 9/32 in. hole here. Existing Hole Towards Side Discharge Template No. 2 48 in. (122 cm) mower template Cut out template here Scale...