Table of Contents
Advertisement
65BDL3051T
6.2.4. PIP menu
Sub mode
Picture
PIP size
PIP position
Screen
PIP change
PIP source
Audio
PIP audio
PIP reset
PIP
P
P
Con guration 1
Sub mode
Select the sub mode.
Choose from: {Off} / {PIP} / {POP} / {Quick swap} / {PBP}.
Off
Quick swap
PIP size
Select the size of the sub picture in the PIP (Picture-in-Picture) mode.
Choose from: {Small} / {Medium} / {Large}.
PIP position
Select the position of the sub picture in the PIP (Picture-in-Picture)
mode.
Choose from: {Bottom-Right} / {Bottom -Left} / {Top-Right} / {Top-
Left}.
PIP change
Exchange Main and PIP / PBP / Quick swap input signal.
PIP source
Select the input signal for the sub picture.
PIP audio
Select the audio source in the Sub mode.
• {Main} - Select audio from the main picture
• {Sub} - Select audio from the sub picture.
PIP reset
Reset all settings in the PIP menu to factory preset values.
O
Small
Bottom-Right
Action
VGA
Main
Action
PIP
PBP 2Win
Sub Win1
Input
Switch main on top or
sub on top.
•
The PIP function is available only for certain signal source
combinations as shown in the table below.
HDMI1 HDMI2
DVI
DisplayPort VGA MediaPlayer Browser SmartCMS
O
X
X
HDMI1
X
O
X
HDMI2
X
X
O
DVI
O
O
O
DisplayPort
O
O
O*
VGA
Media
X
X
X
Player
X
X
X
Browser
X
X
X
SmartCMS
PDF
X
X
X
Reader
X
X
X
Custom
X
X
X
CardOPS
(O: PIP function available, X: PIP function unavailable)
•
The availability of the PIP function will also depend on the resolution
of the input signal being used.
Note: Touch function is only for single full screen. Multiple screen touch
event will be incorrect corresponding.
6.2.5. Configuration1 menu
Switch on state
Picture
Panel Saving
RS232 routing
Screen
Boot on source
WOL
Audio
DDC/CI
Light sensor
PIP
P
Human sensor
Power LED light
Con guration 1
Con guration1 reset
Switch on state
Select the display status used for the next time you connect the power
cord.
•
{Power off} - The display will remain off when the power cord is
connected to a wall outlet.
{Forced on} - The display will turn on when the power cord is
•
connected to a wall outlet.
{Last status} - The display will return to the previous power status
•
(on/off/standby) when removing and replacing the power cord.
Panel saving
Choose to enable the panel saving functions and thus reduce the risk of
"image persistence" or "ghost-imaging".
•
{Brightness} - Select {On} and the image brightness will be reduced
to an appropriate level. The Brightness setting in the Picture menu
will be unavailable when selected.
{Pixel shift} - Select the time interval ({Auto} / {10 ~ 900} Seconds
•
/ {Off}) for the display to slightly expand the image size and shift the
position of pixels in four directions (up, down, left, or right).
RS232 routing
Select the network control port.
Choose from: {RS232} / {CardOPSRS232 (OPS model only)} / {LAN
-> RS232}.
40
PDF
Reader
O
O
X
X
X
X
O
O
X
X
X
X
O
O*
X
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
X
X
O
O
X
O
X
X
O
O
X
X
O
X
O
O
X
X
X
O
O
O
X
X
X
X
O
O
X
X
X
X
Last status
Action
RS232
Action
O
On
O
O
On
Action
Custom CardOPS
X
X
X
X
X
X
O
O
O
O
X
X
X
X
X
X
X
X
O
X
X
O
Advertisement
Table of Contents
Troubleshooting
