Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LG 32WFC
Summary of Contents for LG 32WFC
- Page 1 OWNER’S MANUAL LG Digital Signage (MONITOR SIGNAGE) Please read this manual carefully before operating your set and retain it for future reference. 32WFC CD P/No: SAC37113603 (1608-REV00) WEB P/No: SAC37113601 (1608-REV00) Printed in Korea www.lg.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS SAFETY PRECAUTION ....3 - Precautions In Installing the Product .....3 - Precautions to the AC Adapter and Electrical Power ..................5 - Precautions In Moving the Product ......7 - Precautions In Using the Product ......7 ASSEMBLY AND PREPARATION ..9 - Mounting Holes ..............10 - Portrait Layout ..............11 - Storage Method for Panel Protection ....12... -
Page 3: Safety Precaution
WARNING - This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. SAFETY PRECAUTION Please read these safety precautions carefully before using the product. WARNING If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death. - Page 4 If you install the product in a place that does not meet the recommended conditions, this may cause serious damage to the product’s picture quality, life cycle, and appearance. Please check with LG or a qualified installer before installing. This caution applies to a place where there is an abundance of fine dust or oil mist, chemical substances are used, the temperature is very high or low, the humidity is very high, or the product is likely to remain turned on for a long period of time (airport and train station), failure to do so will invalidate the warranty.
-
Page 5: Precautions To The Ac Adapter And Electrical Power
- If loosely connected, the poor connection may cause a fire or electric shock. • Be sure to use power cords and AC adapters provided or approved by LG Electronics, Inc. - The use of non-approved products may cause a fire or electric shock. - Page 6 • Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered with dust, dry the power plug completely or wipe dust off. - You may be electrocuted due to excess moisture. • If you don’t intend to use the product for a long time, unplug the power cable from the product.
-
Page 7: Precautions In Moving The Product
Precautions In Moving the Product WARNING • Make sure to turn off the product. - You may be electrocuted or the product can be damaged. • Make sure to remove all cables before moving the product. - You may be electrocuted or the product can be damaged. •... - Page 8 CAUTION • Do not put or store inflammable substances near the product. - There is a danger of explosion or fire due to careless handling of the inflammable substances. • When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product.
-
Page 9: Assembly And Preparation
ASSEMBLY AND PREPARATION CAUTION • Always use genuine components to ensure safety and product performance. • The product warranty will not cover damage or injury caused by the use of counterfeit components. NOTE • The accessories provided with your product may vary depending on the model or region. •... -
Page 10: Mounting Holes
Mounting Holes Use M3 screws to mount the monitor. The holes for the screws are on the rear of the product. < Front of the product > < Rear of the product > CAUTION • This product has the front and back sides. Make sure the product is installed with the front side facing forward. •... -
Page 11: Portrait Layout
Portrait Layout To install in portrait mode, rotate the set clockwise 90 degrees when looking at from the front. The portrait mode is only available on the scaler board. (The scaler board should support portrait mode.) CAUTION • You can make a scaler board or purchase AD Box (TSP500-A, TSP300). •... -
Page 12: Storage Method For Panel Protection
Storage Method for Panel Protection Correct Method Panel Cushion When laying the product on a flat floor, pit it face down on a cushion or blanket to prevent scratching and damage. Panel If there is no a cushion or a soft cloth available, ensure the floor is clean. Then lay the product down carefully with the panel facing either upward or downward. -
Page 13: Incorrect Method
Incorrect Method Panel If the product is tilted onto the bezel, the bottom of the panel may be damaged. Panel If the product is tilted onto the edge of the panel, the panel may be damaged. -
Page 14: Product Installation
PRODUCT INSTALLATION Installing an LVDS Cable The LVDS cable port is located as shown in the figure below. When installing the product, make sure there is enough space to install the LVDS cable. 30 mm 45 mm LVDS Cable (Not included) NOTE •... -
Page 15: Lighting Installation
Lighting Installation This product must be installed with backlighting. Lighting must be installed behind the product so that the display can be seen clearly. 600 lux or more Lighting (When the Full Screen is White.) If something obstructs the backlighting, additional lighting may be required. Additional lighting 600 lux or more Lighting... -
Page 16: Installation In Enclosure
Installation in Enclosure Install the product in the enclosure. Wear work gloves when installing the product. Do not use bare hands. Otherwise, it may cause personal injury. Place the product in the enclosure. Attach the product using the prepared screw holes and an additional enclosure guide frame. NOTE •... - Page 17 <Example of the product in the enclosure> <Example of the lighting installation> Lighting must be installed in the enclosure.
-
Page 18: Precaution
Precaution Correct Method Do not hold the screen area when holding the product. Use a soft cloth moistened with n-hexane to remove dust or stains on the screen. CAUTION • If a fixed image displays on the screen for a long period of time, it will be imprinted and become a permanent disfigurement on the screen. -
Page 19: Incorrect Method
Incorrect Method Do not lift up the product by holding a corner. CAUTION • Make sure the power is disconnected before moving or installing the product. Otherwise electric shock may occur. • Wear working gloves when installing the product. Do not use bare hands. Otherwise, it may cause personal injury. •... -
Page 20: Troubleshooting
TROUBLESHOOTING After-image appears on the product. Problem Action After-image appears when the product is • If you use a fixed image for a long time, the pixels may be damaged. turned off. Use the screen-saver function. • When a dark image is displayed on the screen after an image with high contrast (black and white or gray), this may cause image sticking. -
Page 21: Product Specifications
PRODUCT SPECIFICATIONS The product specifications below may be changed without prior notice due to upgrade of product functions. Active Screen Size 80 cm diagonal Dimensions (Width x Height x Depth) / 743.2 mm x 504.2 mm x 11.2 mm / 2.7 kg Weight Pixel Pitch 0.36375 mm x 0.36375 mm... - Page 22 (Unit : mm) 16-Mounting Ready Hole (M3 Tap) 743.2 51.6 51.6 46.6 46.6...
-
Page 23: Lvds Pin Map Guide
LVDS PIN MAP GUIDE • LCD Connector (CN1) : FI-RE51S-HF or Equivalent, refer to below table. • Mating Connector : FI-RE51HL • Cable length: 1 m of coaxial cable or less Pin No. Symbol Description Note NC or GND No Connection or Ground No Connection No Connection No Connection... - Page 24 Pin No. Symbol Description Note R2DN SECOND LVDS Receiver Signal(D-) R2DP SECOND LVDS Receiver Signal(D+) No Connection No Connection NC or GND No Connection or Ground NC or GND No Connection or Ground Ground Ground Ground No Connection VLCD Power Supply+12.0V VLCD Power Supply+12.0V VLCD...
- Page 25 Make sure to read the Safety Precautions before using the product. The model and serial numbers of the SET are located on the back and one side of the SET. Record it below should you ever need service. MODEL Temporary noise is normal when powering ON or OFF this device.