- Optional Accessories ..........11 - Terminal Buttons and Status Display .... 12 - Rack Installation (Optional) ........ 13 - Connecting LPLG001 to LAN Hub ....14 - Power Supply to LPLG001 ......... 15 - Power Redundancy Feature ....... 17 - Hot Swap Feature and Sequence ....
WARNING - This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference. SAFETY PRECAUTION Please read these safety precautions carefully before using the product. WARNING • If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death. CAUTION •...
Page 4
If you install the product in a place that does not meet the recommended conditions, this may cause serious damage to the product’s picture quality, life cycle, and appearance. Please check with LG or a qualified installer before installing. This caution applies to a place where there is an abundance of fine dust or oil mist, chemical substances are used, the temperature is very high or low, the humidity is very high, or the product is likely to remain turned on for a long period of time (airport and train station).
- If loosely connected, the poor connection may cause a fire or electric shock. • Be sure to use power cords and AC adapters provided or approved by LG Electronics, Inc. - The use of non-approved products may cause a fire or electric shock.
Page 6
• If you don’t intend to use the product for a long time, unplug the power cable from the product. - Covering dust can cause a fire, or insulation deterioration can cause electric leakage, electric shock or fire. • Fix the power cable completely. - If the power cable is not fixed completely, a fire can break out.
Precautions In Moving the Product WARNING • Make sure to turn off the product. - You may be electrocuted or the product can be damaged. • Make sure to remove all cables before moving the product. - You may be electrocuted or the product can be damaged. •...
Precautions In Using the Product WARNING • Do not disassemble, repair or modify the product at your own discretion. - Fire or electric shock accident can occur. - Contact the service center for check, calibration or repair. • When the display is to be left unattended for an extended period of time, unplug it from the wall outlet. •...
• Set the appropriate resolution and clock by referring to the User’s Guide. - Your vision can be impaired. • Use authorized detergent only when cleaning the product. (Do not use benzene, thinner, or alcohol.) - Product can be deformed. •...
ASSEMBLING AND PREPARING CAUTION • Always use genuine components to ensure safety and durability of the product. • The product warranty will not cover damage or injury caused by the use of unauthorised components. • Replacing the batteries with the wrong type may result in explosion. •...
Optional Accessories Without prior notice, optional accessories are subject to change to improve the performance of the product, and new accessories may be added. The images in this user manual may differ from the actual product and optional accessories. System Controller LED Controller LCLG003* LLLG003*...
Supplies the AC power. • Updates the SVC firmware. • Enables the user to control the LPLG001 via the connection with the LAN hub. • Checks when a problem occurs in the operation of a set for SVC. • Power output terminal.
Check if the System Controller is connected to the LAN hub that has been already connected. Only when the System Controller is connected to the LAN hub, the LPLG001 can be controlled, and the function to monitor the operational status becomes available.
Power Supply to LPLG001 The main purpose of LPLG001 is to supply power to the LED Display module and the LED Controller. There are three power output terminals ( terminal), through which power is supplied.
Page 16
Check the direction so that the cable is not damaged. • When connecting the power output terminal ( terminal) of the LPLG001 to the interface board, always use the 4-pin power cable that came with the product. • When connecting the interface board to the LED Display Module, power gender, and LED Controller, make sure to use the provided 24-pin power cable.
Power Redundancy Feature The user can turn the feature of the LPLG001 model on or off via the switch on the rear side. Feature ON - Even if a problem occurs in one of the four power boards, the set will not be off, and the power will be supplied to the LED screen.
Hot Swap Feature and Sequence Even if the set is not off (when the power is supplied to the LED screen), you can replace the power boards that need to be repaired one by one. While you are replacing the power boards, the LED screen will not be off.
Page 19
CAUTION • Always replace them in the same sequence as described in the figure.
TROUBLESHOOTING There is no power output. Problem Solution Is the power cord connected to the • Check if all four power cords are properly plugged into the power product? outlet. Is the power cord terminal switched off? • Check if all switches of the power cord terminal are on. Are you using the product properly •...
PRODUCT SPECIFICATIONS Without prior notice, all product information and specifications contained in this manual are subject to change to improve the performance of the product. If you want to use the product with less noise, please contact the service center. symbol means alternating current, and the symbol means direct current.
Page 23
The model and serial number of the product are located on the back and on one side of the product. Record them below in case you ever need service. MODEL Temporary noise is normal when powering ON or OFF this device.
Need help?
Do you have a question about the LPLG001 and is the answer not in the manual?
Questions and answers