Advertisement
Quick Links
COSMOS SINGLE OTTOMAN BEDSTEAD
2020127
IMPORTANT – READ CAREFULLY – RETAIN FOR FUTURE REFERENCE
Dimensions
Width -96.5cm
Depth - 203cm
Height - 108cm
Need Help? Contact X Rocker at :
www.xrockeruk.com/pages/support
IMPORTANT: You must keep your original retail receipt as proof of purchase.
1
KT-10/30/2020
Advertisement
Related Manuals for X Rocker COSMOS 2020127
Summary of Contents for X Rocker COSMOS 2020127
- Page 1 2020127 IMPORTANT – READ CAREFULLY – RETAIN FOR FUTURE REFERENCE Dimensions Width -96.5cm Depth - 203cm Height - 108cm Need Help? Contact X Rocker at : www.xrockeruk.com/pages/support IMPORTANT: You must keep your original retail receipt as proof of purchase. KT-10/30/2020...
- Page 2 Safety and Care Advice Important Please read these instructions fully before starting assembly Check you have all the Make sure you have enough Assemble on a soft level components and tools listed on space to layout the parts before surface to avoid damaging the the following pages.
- Page 3 Components - Panels Please check you have all the panels listed below Headboard x1 Footboard x1 Side Panel x1 Side Panel x1 Gas Lift x2 Leg x4 Mattress Support x2 Short Support Leg x1 Hinge x2 Back Tube x1 Front Tube x1 Center Rail x1 Wooden Slats x22 Bracket x1...
- Page 4 Components - Panels Please check you have all the panels listed below Support Rail x1 Cross Rail x1 Support Rail x2 Base Boards x2 Base Support x2 Single Slat Cap x22 Double Slat Cap x11 Strap x1 Side Rail x2 Bed Frame Support Bar x2 Buckle x1 Buckle x1...
- Page 5 Components - Fittings Please check you have all the panels listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied are required. 20mm M6 Bolt x 50 15mm M6 Bolt x 6 30mm M6 Bolt x 12 35mm M6 Bolt x 5 40mm M6 Bolt x 9...
- Page 6 Assembly Instructions Step 1 Step 1 Attach with 100% E x8 J x1 40mm M6 Bolt...
- Page 7 Assembly Instructions Step 1 Step 2 B x4 J x1 C x4 20mm M6 Bolt 30mm M6 Bolt...
- Page 8 Assembly Instructions Step 1 Step 3 Attach with Attach Attach with 100% B x4 J x1 20mm M6 Bolt...
- Page 9 Assembly Instructions Step 1 Step 4 Attach with Attach with 100% F x4 J x1 C x8 65mm M8 Bolt 30mm M6 Bolt...
- Page 10 Assembly Instructions Step 5 Attach with Attach with 100% B x12 J x1 20mm M6 Bolt...
- Page 11 Assembly Instructions Step 1 Step 6 Hang sub-assembly as illustrated, don't completely tighten the bolts until STEP 8 is complete.
- Page 12 Assembly Instructions Step 1 Step 7 Attach with B x4 J x1 20mm M6 Bolt...
- Page 13 Assembly Instructions Step 1 Step 8 Attach with Attach with D x1 A x6 J x1 35mm M6 Bolt 15mm M6 Bolt...
- Page 14 Assembly Instructions Step 1 Step 9 Gently place base boards inside the assembled bed base.
- Page 15 Assembly Instructions Step 1 Step 10 Attach...
- Page 16 Assembly Instructions Step 1 Step 11...
- Page 17 Assembly Instructions Step 1 Step 12 Attach with Attach with 100% K x1 G x4 D x4 B x4 J x1 35mm M6 Bolt 20mm M6 Bolt...
- Page 18 Assembly Instructions Step 1 Step 13 Attach with 100% B x4 J x1 20mm M6 Bolt...
- Page 19 Assembly Instructions Step 1 Step 14 Attach with 100% E x1 J x1 40mm M6 Bolt...
- Page 20 Assembly Instructions Step 1 Step 15 Attach with 100% B x4 J x1 20mm M6 Bolt...
- Page 21 Assembly Instructions Step 1 Step 16 Attach with 100% H x4 K x1...
- Page 22 Assembly Instructions Step 1 Step 17 Attach with 100% I x8 B x8 J x1 20mm M6 Bolt...
- Page 23 Assembly Instructions Step 1 Step 18 Attach with 100% B x6 J x1 20mm M6 Bolt...
- Page 24 Assembly Instructions Step 1 Step 19 19.1 Insert into 19.2 Press into , repeat the same procedure for the opposite side of the bed with a new 19.3 Insert ends of both slats into , then press into as illustrated. Repeat the same procedures going backwards for every row of slats.
- Page 25 Assembly Instructions Step 1 Step 20...
- Page 26 Assembly Instructions Step 1 Step 21 120° When using LED: 1. Point to the signal receiver with remote controller. 2. Get a good singal within 2 meters. FLASH STROBE FADE SMOOTH...
- Page 27 Assembly Instructions Step 1 Step 22...
- Page 28 Assembly Instructions Step 1 Step 23...
- Page 29 Contact a specialist. Risk of damage to the eyes! Never look directly into the LED. If you can’t fix the fault yourself, contact X Rocker support. Please be aware that any improper repairs will also invalidate the warranty and The light can only be used in dry indoor areas.
- Page 30 The packaging consists of cardboard and marked plastics that can be recycled. – Take these materials to a recycling centre. Technical data Article number LS8837-3.75M Dimensions 1250x10mm(x3) LEDs 225xLED 5050 Capacity Protection class Degree of protection IP20 -20 to +60 ℃ Operating temperature LED controller Rated voltage...
- Page 31 1. The bed can only be used with the supplied adapter. The external flexible cable of this transformer cannot be replaced. If the cord is damaged, the transformer should be discarded. 2. Do not expose the adapter to rain or moisture. Use the adapter indoors only to avoid the risk of electric shock or fire.