Table of Contents
Advertisement
R4D225-AK10-06
3.2 Nominal data
Motor
M4D094-FA
Phase
3~
Nominal voltage / VAC
400
Wiring
Y
Frequency / Hz
50
Method of obtaining
ml
data
Valid for approval/
CE
standard
Speed (rpm) / min
-1
1350
Power consumption / W
380
Current draw / A
0.75
Min. back pressure / Pa
0
Min. ambient
-40
temperature / °C
Max. ambient
90
temperature / °C
Starting current / A
2.8
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Data according to Commission Regulation (EU) 327/
2011
01 Overall efficiency η
/ %
es
02 Measurement category
03 Efficiency category
04 Efficiency grade N
05 Variable speed drive
06 Year of manufacture
07 Manufacturer
08 Type
09 Power consumption P
/ kW
e
09 Air flow q
/ m³/h
v
09 Pressure increase total p
/
sf
Pa
-1
10 Speed (rpm) n / min
11 Specific ratio
*
12 Recycling/disposal
13 Maintenance
14 Additional components
*
Specific ratio = 1 + p
/ 100 000 Pa
fs
Data obtained at optimum efficiency level. The ErP data is determined using a motor-impeller
combination in a standardized measurement setup.
Item no. 10710-5-9970 · ENU · Change 213948 · Approved 2020-03-26 · Page 6 / 12
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
3~
400
Y
60
ml
CE
1500
540
0.94
50
-40
60
2.7
Actual
Req. 2015
34.1
33
A
Static
45.1
44
No
The year of manufacture is specified on the
product's rating label.
ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart
· HRA 590344
D-74673 Mulfingen
R4D225-AK10-06
0.18
755
295
1445
1.00
Information on recycling and disposal is
provided in the operating instructions.
Information on installation, operation and
maintenance is provided in the operating
instructions.
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.
3.4 Technical description
Weight
6.1 kg
Size
225 mm
Motor size
94
Rotor surface
Painted black
Impeller material
Sheet steel, galvanized
Direction of rotation
Clockwise, viewed toward rotor
Degree of protection
IP54
Insulation class
"F"
Moisture (F) /
H1
Environmental (H)
protection class
Installation position
Any
Condensation
None
drainage holes
Mode
S1
Motor bearing
Ball bearing
Touch current
<= 3.5 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Motor protection
Thermal overload protector (TOP) with
basic insulation
with cable
Variable
Protection class
I (with customer connection of protective
earth)
Conformity with
EN 60034-1 (2010); CE
standards
Approval
EAC
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
; Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.
3.5 Mounting data
Strength class of
8.8
screws
For screw clearance, see Chapter 3.1 Product drawing
; Secure the screws against unintentional loosening (e.g. use self-
locking screws).
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
Advertisement
Table of Contents
