Subscribe to Our Youtube Channel
Related Manuals for Renogy MTS-WM
Summary of Contents for Renogy MTS-WM
- Page 1 MTS-WM RENOGY Wall Mount System 2775 E Philadelphia St, Ontario, CA 91761 1-800-330-8678...
- Page 2 Important Safety Instructions Please save these instructions. This manual contains important safety, installation, and operating instructions for the Renogy Wall Mount System. The following symbols are used throughout the manual to indicate potentially dangerous conditions or important safety information. WARNING: Indicates a potentially dangerous condition. Use extreme caution when performing this task.
-
Page 3: Table Of Contents
Table of Contents General Information ............................4 Identification of Parts ............................. 5 Installation ................................7 Attach the Fixed Bracket and Tilt Arm ....................8 Attach the Panel to the Wall Mount ....................10 Install the Wall Mount on Wall ......................11 Install the Wall Mount on Pole ...................... -
Page 4: General Information
General Information The Renogy Wall Mount System is designed for off-grid applications, when mounting on a roof is not applicable. It supports Renogy solar panels up to 50W. The system comes complete with all fasteners to secure the system to the installation surface. This system makes the installation of small solar systems easy, affordable and quick. -
Page 5: Identification Of Parts
Identification of Parts Image Component Quantity Tilt Arm (A) Fixed Bracket (B) M8 T-Bolt (C) M8 Washer (D) M8 Spring Washer... - Page 6 End Clamp (F1) End Clamp (F2) M8 Nut (G) Hose Clamp (H1) 2.6 to 3.5 in.
-
Page 7: Installation
Hose Clamp (H2) 3.3 to 4.3 in. Hose Clamp (H3) 4.1 to 5.0 in. Expansion Bolt (I) Table 1 Installation Recommended tools to have before installation (Not provided): • Socket wrench • Torque extension • Box-Leveler • Tape Measure • 18mm wrench or socket for larger hex nut •... -
Page 8: Attach The Fixed Bracket And Tilt Arm
Attach the Fixed Bracket and Tilt Arm Figure 1 Figure 2... - Page 9 Figure 3 Note: M8 Washer (D) and M8 Spring Washer (E) are essential parts when tightening M8 Nut (G), over tightening may damage parts Note: Adjust tilt arm (A) and fixed bracket (B) to desired angle prior to tightening M8 Nut Figure 4...
-
Page 10: Attach The Panel To The Wall Mount
Attach the Panel to the Wall Mount Figure 5 Figure 6 WARNING! Keep hands clear of pinch points! -
Page 11: Install The Wall Mount On Wall
Figure 7 NOTE: This is what the clamp should look like when it is fastened to the panel. Install the Wall Mount on Wall Figure 8 NOTE: Please check the direction of Fixed Bracket (B) prior to installation. - Page 12 Figure 9 NOTE: Please use proper tool for this installation. Installation process may require assistance.
-
Page 13: Install The Wall Mount On Pole
Install the Wall Mount on Pole Figure 10 NOTE: Please check the direction of Fixed Bracket (B) prior to installation. Choose appropriate Hose Clamp (H) size for installation. NOTE: Please use proper tool for this installation. Installation process may require assistance. -
Page 14: Wall Mount Dimensions
Wall Mount Dimensions Tilt Arm (A) Fixed Bracket (B) NOTE: Dimensions in inches. -
Page 15: Compatibility
RNG-80D-SS INCOMPATIBLE RNG-100D INCOMPATIBLE RNG-100D-S INCOMPATIBLE RNG-100D-SS INCOMPATIBLE RNG-100D-SSP INCOMPATIBLE RNG-100MB INCOMPATIBLE RNG-100D-R INCOMPATIBLE RNG-160D-SS INCOMPATIBLE RNG-300D COMPATIBLE RNG-50P INCOMPATIBLE RNG-100P INCOMPATIBLE RNG-160P INCOMPATIBLE RNG-270P INCOMPATIBLE RNG-320P Renogy reserves the right to change the contents of this manual without notice.
Need help?
Do you have a question about the MTS-WM and is the answer not in the manual?
Questions and answers