Advertisement
3. Using the correct bit for the type of wall, drill
sufficiently large holes to accommodate the 5/16"
all-thread rod.
4. Insert a lock washer and a nut on three of the four
all-thread rods. On the fourth, install a lock washer,
the chain mounting bracket, and then the nut.
Note: It is important that the end of the all-thread
rod is flush with the nut.
5. Put the vault up to the wall (drain hole down) and
insert two all-thread rods through the top two
mounting holes. Insert the all-thread rod that you
have attached the chain mounting bracket to through
the lower left hole. Insert the last all-thread rod into
the bottom right hole. (See Figure 5.)
6. On the other side of the wall, mount the interior
cover plate (optional) onto the all-thread rods. Put
a 5/16" fender washer, and a 5/16" lock washer on
each of the all-thread rods. Last, put a 5/16" nut on
each rod and hand tighten without letting the rod
rotate. (See Figure 5.)
7. With one hand, grip the end of the all-thread rod with
either a plier, or vice grip. Then, with the other hand,
tighten the nut with a 1/2" wrench while making sure
the Vault stays level. Repeat this procedure for all
four rods, and tighten to approximately 50-75in-lb or
until firmly snug.
8. Cut off the excess all-thread rod using an
appropriate tool.
Tamper Switch (Optional)
The tamper switch is required for commercial burglar
alarm applications. The tamper switch should be tested
annually.
If you are using the optional tamper switch, attach the
tamper switch to the wiring in the wall (see Figure 3).
Note: Tamper switch wiring must conform to NEC class
2 or 3; or UL class 634 standards. Electrical range
should be 30 VDC at 50 MA. Use AMP FDVH 187C
(14/16 AWG) crimp connectors, or equivalent and 14/16
AWG wire.
Install TRAC-Lid BT
To place the TRAC-Lid BT in the TRAC-Vault BT, the
lock blades on the side of the TRAC-Lid BT must be
retracted. Refer to the user instructions provided with
your DisplayKEY or eKEY for step by step operation.
Important: When installing a TRAC-Lid BT you MUST
record the serial number of the TRAC-Lid BT installed at
each location. This important information is necessary
for the integrity of the TRACcess database.
Retract the Blades:
1. Push the chrome button until the red LED blinks to
turn on the TRAC-Lid.
2. While it blinks, use a DisplayKEY or eKEY to
perform the Open Device function.
Note: For DisplayKEY, point the top of the key at the
blinking LED.
3. When the communication is complete and access is
allowed, the LED of the TRAC-Lid will flash green.
Note: The lock can only be opened when the LED
flashes green.
4. Rotate the thumb lever counterclockwise until it
stops.
5. Remove the TRAC-Lid from the vault. Leave the
lever in the open position until relocking the device.
Note: If the lever is turned clockwise after the lock
LED stops flashing green then another open device
procedure will need to be performed to replace the
TRAC-Lid.
6. To lock the device, return the TRAC-Lid to the vault
and turn the lever clockwise until it stops.
7. Check to insure that the TRAC-Lid is secured to the
vault before leaving the site.
Install the TRAC-Lid BT into the TRAC-Vault BT:
1. Attach the provided chain to the TRAC-Lid BT.
2. Insert the loose end of the chain through the eyehole
on the back of the TRAC-Lid BT.
3. Using pliers, crimp the end of the chain to the
bracket inside the TRAC-Vault BT.
Regulatory Compliance
United States (FCC)
This device complies with part 15 of the FCC rules. Operation is subject to the
following conditions:
1.
This device may not cause harmful interference.
2.
This device must accept any interference received, including interference
that may cause undesired operation
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Canada (IC)
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
Cet équipement est conforme à la (aux) norme(s) canadienne(s) d'exemption
de licence RSS Industry Canada. Son opération est sujette aux deux conditions
suivantes: (1) cet équipement ne provoquera aucune interférence et (2) cet
équipement doit tolérer toute interférence pouvant provoquer une opération
indésirable de l'équipement.
European Union (CE)
This Class B digital apparatus conforms to the requirements of the following EU
directives:
1.
R&TTTE Directive (1999/5/EC)
2.
WEEE Directive (2002/96/EC)
Warranty
UTC Fire & Security (UTCFS) warrants that this product will be free
of defects in material and workmanship for one year from the date of
purchase. This warranty is limited to repair or replacement at the option
of UTCFS. Damages caused by modification, abuse or misuse, wear and
tear, improper installation, application, storage, or fault or negligence of
a party other than UTCFS are not covered. UTCFS will be responsible
for labor costs of removal or reinstallation of products. The repaired or
replaced product is then warranted under the terms of this limited warranty
for the balance of the term of the warranty or for 90 days, whichever
is longer. UTCFS MAKES NO OTHER WARRANTY, EXPRESS OR
IMPLIED, OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. IN NO EVENT SHALL UTCFS BE LIABLE FOR LOSS OF
USE; LOST PROFITS; THEFT; PROPERTY DAMAGE; OR SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES. To obtain repair or
replacement information under the terms of this warranty, please contact
your local supplier.
3
Advertisement
