Advertisement
2.3 Safety notices
Heavy weight
Danger of injury due to heavy weight of the parts! 2 men handling
•
Handle all packing units and parts carefully with both hands, especially the weight
segments, and set them down carefully. If possible, use transport aids for transport of
the stand.
•
Do not stack packing units and parts.
•
Wear sturdy shoes during transport and assembly of the stand
During transport and assembly you will have to handle heavy parts. Parts can fall or over-
turn, resulting in severe injuries due to their heavy weight.
Unexpected overturning
Danger of injury and danger of property damage due to overturning!
•
Never use the sunshade stand without first having inserted all weight segments. Use
only original weights.
•
Use the sunshade stand only with sunshades that are suitable for the weight class of
the sunshade stand. Observe the specifications of the sunshade manufacturer.
•
Do not use the sunshade in case of strong wind. During strong winds, fold up the sun-
shade or remove it from the stand.
•
Do not leave the sunshade stand unattended when the sunshade is open.
If the sunshade stand is not handled as intended it can overturn together with the sunsha-
de, resulting in injuries and property damage.
Weight segments
Danger of pinching and danger of cuts/scrapes from the weight segments!
•
Handle the weight segments carefully and wear work gloves
When inserting the weight segments, there is a danger of being cut or scraped by the
weight segments and pinching of fingers between the weight segment and the base.
6
5
Using the sunshade stand
5.1
Inserting the sunshade
mounting tube to the sunshade pole diameter.
If an unsuitable reducing sleeve for the pole diameter is used (if the sleeve is too
large) the sunshade can overturn, resulting in injuries and property damage.
The clamp must be attached as follows:
2. Open the quick-release clamp by turning the clamping lever counter-clockwise a
few turns (Fig. 15).
3. Insert the correct reducing sleeve for the sunshade into the clamp from below (Fig.
16) and push it up as far as it will go.
4. Unscrew the lower allen screw (Fig. 17/1) until the clamp opens.
5. Place the clamp on the mounting tube so that the retainer clip (Fig. 18/1) is in
position of the telescoping lever (Fig. 18/2) and press the telescoping rod into the
retainer clip.
6. Tighten the lower Allen screw (Fig.19)..
5 Using the sunshade stand
5.1
Inserting the sunshade
Danger of injury and danger of property damage due to overturning!
Use the sunshade stand only with sunshades that are suitable for the weight class
of the sunshade stand. Observe the specifications of the sunshade manufacturer.
Do not open the sunshade to put it into the stand.
Do not use the sunshade in case of strong wind. During strong winds, fold up the
sunshade or remove it from the stand.
If the sunshade stand is not used as intended it can overturn together with the
sunshade, resulting in injuries and property damage.
Modell: 220S
For model 220S, insert the sunshade as follows:
1. Make sure that the sunshade stand is in standing position, i.e. the telescoping rod
is parallel to the mounting tube and secured on the retaining clip (Fig. 20).
2. Unscrew the three knurled screws of the clamp (Fig. 20) until the pole fits into the
mounting tube.
3. Push the pole of the sunshade into the mounting tube as far as it will go.
4. Turn the three knurled screws alternately until the pole is held tightly in the center.
Modell: 220S with Quick Clamp Accessory QC-2
For model 220S with Quick Clamping Accessory QC-2, insert the sunshade as follows:
1. Make sure that the sunshade stand is in standing position, i.e. the telescoping rod
is parallel to the mounting tube and secured on the retaining clip (Fig. 21).
15
Advertisement
