Related Manuals for Haklift AC50-A
Summary of Contents for Haklift AC50-A
- Page 1 Operate manual & Parts manual Hand Pallet Truck with AC Pump AC50-A WH10L-35-A WH20L-51-A WH25L-51-A Note: Owner and operator MUST read and understand this operating instructions before use this pallet truck.
-
Page 2: General Specifications
All of the information reported herein is based on data available at the time of printing. The factory reserves the right to modify its own products at any time without notice or incurring in any sanction. Please verify with the factory for possible updates. 1. GENERAL SPECIFICATIONS AC50-A WH10L-35-A WH20L-51-A WH25L-51-A Model No. - Page 3 . Draw-bar 2. Pin 3. Axle with hole 4. Elastic pin 5. Fork frame (Fig. 1) When attaching the handle, you had better squat just behind the pallet truck. Then you: 2.1. Insert the draw-bar onto the pump piston (A), then use a hammer to insert the axle with hole (K) into the hydraulic pump and draw-bar from the right to left.
-
Page 4: To Adjust Release Device
3. TO ADJUST RELEASE DEVICE On the draw-bar of this pallet truck, you can find the control handle which can be regulated in three positions : Raise - handle down Drive position - handle in center position Lower - handle up, the lever moves back the drive position when released. If however they have been changed, you can adjust according to following step: 3.1 If the forks elevate while pumping in the DRIVE position, turn the adjusting nut on the adjusting bolt or adjusting screw clockwise until pumping action does not raise the forks and the DRIVE... -
Page 5: Troubles Shooting
4.4 LUBRICATION Use motor oil or grease to lubricate all moveable parts. 5. GUIDE TO SAFETY OPERATION For safe operation of the Hand Pallet Truck, please read all warning signs and instructions here and on the pallet truck prior to use. 5.1 Do not operate the pallet truck unless you are familiar with it and have been trained or authorized to do so. - Page 6 - The impurities in the oil cause the release valve to be unable to close - Replace with new oil. fork tight. - Inspect and replace the waste descends - Some parts of hydraulic system is parts. without cracked or bored. - Banish the air.
- Page 7 AC50-A General parts Item Parts No. Parts details Qty. Item Parts No. Parts details Qty. 17050101 Steel Ø78*66 17050119 Shaft for loading wheel Ø20*94 Loading wheel 17050101-1 NylonØ80*66 17050120 Bearing 6204# 17050102 Truck frame 17050121 Wheel cradle 17050103 Axle for joint Ø25*64 17050122 Spring pin Ø5*35...
- Page 8 AC50-A Pump & handle parts details Item Parts No. Parts name Qty. Item Parts No. Parts details Qty. 17050201 AC pump body 17050301 Draw-bar 17050202 Composite gasket Ф10*2 17050302 Rubber pad 17050203 Plug screw M10*1*10 17050303 Spring Pin 17050204 Piston rod Ф45*290 17050304 Blade Spring 17050205 Seal washer UHSФ45*55*6...
- Page 9 WH20L-51-A/WH25L-51-A Frame parts details Item Parts No. Parts details Qty. Item. Parts No. Parts details Qty. 17070101 AC Oil pump 17070124 Shaft for double load wheel Ø17*94 17070102 Fork Frame for WH20L-51-A 17070125 Tandem Mounting Plate 17070102-1 Fork Frame for WH25L-51-A 17070126 Washer 17070103 Screw M6*14 17070127 Bearing...
- Page 10 WH20L-51-A/WH25L-51-A Pump & handle parts details Item Parts No. Parts name Qty. Item Parts No. Parts details Qty. 17070201 AC pump body 17070301 Draw-bar 17070202 Small pump core Ø18*107 17070302 Rubber pad 17070203 Spring cover Ø49*2*15 17070303 Spring Pin 17070204 Big spring Ø5.5*48*115 17070304 Blade Spring 17070205 Dust ring Ø18*26*4.5/6 17070305 Torsional Spring...
- Page 11 WH10L-35-A Frame parts details Item Parts No. Parts details Qty. Item. Parts No. Parts details Qty. 17060101 AC Oil pump (Special) 17060121 Shaft for handle Ø20*103 17060102 Fork Frame 17060122 Connected socket 17060103 Screw M8*16 17060123 Bolt M10*20 17060104 17060124 Shaft for double load wheel Ø12*78 Rocker arm 17060104-1 17060125 Spring pin Ø8*45...
- Page 12 WH10L-35-A Pump & handle parts details Item Parts No. Parts name Qty. Item Parts No. Parts details Qty. 17060201 AC pump body 17060301 Draw-bar 17060202 Small pump core Ø18*107 17060302 Rubber pad 17060203 Spring cover Ø49*2*15 17060303 Spring Pin 17060204 Big spring Ø5.5*48*115 17060304 Blade Spring 17060205 Dust ring Ø18*26*4.5/6...