Advertisement
5. Maintenance instruction
Caution
Do not use damaged/deformed product. If abnormal noise or vibration occurs, stop use immediately, then inspect and ask
manufacturer for help.It is recommended that this inspection be made by a manufacturer's or supplier's authorized repair facility.
Caution
The greatest single cause of failure in hydraulic units is dirt.
• Keep the service jack clean and well lubricated to prevent foreign matter from entering the system. If the jack has been exposed to rain,
snow, sand, or grit, it must be cleaned before it is used.
• Store the jack, with pistons completely retracted, in a well-protected area where it will not be exposed to corrosive vapors, abrasive dust, or
Scale: 1:1
Document Ref: 8940169914_REV: 01 _ 05-2012
any other harmful elements.
• Periodically check the condition of the product.
• Store the product in dry and non-corrosion environment.
• Owners and/or operators should be aware that repair of this equipment may require specialized knowledge and facilities. It is recommended
Scale: 1:1
Document Ref: 8940169914_REV: 01 _ 05-2012
that an annual inspection of the product be made by a manufacturer's or supplier's authorized repair facility and that any defective parts,
decals, or safety labels or signs be replaced with manufacturer's or supplier's specified parts. A list of authorized repair facilities is available
from the manufacturer or supplier, please call them for help.
• Any product that appears to be damaged in any way, is found to be worn, or operates abnormally SHALL BE REMOVED FROM SERVICE
UNTIL REPAIRED. It is recommended that necessary repairs be made by a manufacturer's or supplier's authorized repair facility if repairs are
permitted by the manufacturer or supplier.
• Only attachments and/or adapters supplied by the manufacturer shall be used.
6. Trouble Shooting
Fault
Cause
Trolley Jack does not lift
1) The descent valve was not closed properly
the load
2) Not enough oil
3) Too much oil in the reservoir
Trolley Jack does not hold
4) Same reason like in 1)
the load
5) The hydraulic oil is contaminated with particles or dirt
Trolley Jack does not lift
6) Same reason like in 2)
the load up to the indicated
7) are air bubbles in the hydraulic system for instance from
maximum height
transport
Saddle can not be lowered
8) Same reason like in 5)
entirely
9) The spring /spring position 2 ,is /are not attached properly
or worn out
Trolley Jack lifts with
10) Same reason like in 7)
difficulties
11) Same reason like in 3)
The design has been validated according: ASME PALD-2009
CP80021/CP80030/CP80031:
7. Declaration of conformity
We : CHICAGO PNEUMATIC Tool Co.
Declare that the product(s): CP80015/CP80020/CP80021/CP80030/CP80031
Machine type(s): Trolley jack Origin of the product: China
is in conformity with the requirements of the council Directives on the approximation of the laws of the Member States relating : to
"Machinery" 2006/42/EC (17/05/2006)
applicable harmonised standard(s) : EN 1494:2000 + A1:2008
Name and position of issuer: Nicolas Lebreton ( R&D Manager)
Place & Date: Saint-Herblain,
Technical file available from EU headquarter.
Original Instructions are in English. Other languages are a translation of the original instructions.
Copyright 2014, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks,
model denominations, part numbers and drawings. Use only authorized parts. Any damage or malfunction caused by the use of unauthorized
parts is not covered by Warranty or Product Liability.
CP80015/CP80020/CP80021/CP80030/CP80031
Remedy
please colse the valve by turning the pump rod clock-wise
Low the saddle entirely and top up the hydraulic oil,unitl 4 mm under rim of the
oil plug on the cylinder
Please lower rhe lifting arm entirely and check the oil level. If the oil level is
higher than 4mm underneath the oil plug ,please remove some oil from tank.
The oil level should not be higher than 4mm underneath the rim of the oil plug.
Please proceed as described in 1)
As a quick cure ,please turn the pump rod clockwise adn step on the front
wheel, pull up the lifting arm on the saddle entirely, release the saddle and
lower the lifting arm entirely bu turning the pump rod anti-clockwise. Close
the descent valve again by turning the pump rod clockwise and try to use the
tool again
Please proceed as described in 2)
Please proceed as described in 5)
Please proceed as described in 5)
Clean and lubricate all moving part regular and exchange all damaged and
worn part with new original parts
Please proceed as described in 5)
Please proceed as described in 3)
Serial Number: From 00001 to 99999
Learn more about car jacks we have.
Trolley jack
Advertisement
