Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Acer S200HL
Summary of Contents for Acer S200HL
- Page 1 Acer LCD Monitor User Guide...
- Page 2 Serial number: ___________________________________ Date of purchase: ________________________________ Place of purchase: ________________________________ Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies’ product names or trademarks are used herein for identification purposes only and belong to their respective companies.
-
Page 3: Information For Your Safety And Comfort
Information for your safety and comfort Safety instructions Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. Special notes on LCD monitors The following are normal with the LCD monitor and do not indicate a problem. •... -
Page 4: Safe Listening
• Your device uses one of the following power supplies: Manufacture : Hipro Electronics Co.,Ltd. Model:HP-A0301R3 (S200HL Model) Manufacture : Delta Electronics Inc., Model: ADP-30MH B (S200HL Model) Using electrical power • This product should be operated from the type of power indicated on the marking label. -
Page 5: Product Servicing
• Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord. • If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. -
Page 6: Additional Safety Information
We at Acer are very conscious of the environmental effects of our business and strive to identify and provide the best working procedures to reduce the environmental impact of our products. -
Page 7: Lcd Pixel Statement
LCD pixel statement The LCD unit is produced with high-precision manufacturing techniques. Nevertheless, some pixels may occasionally misfire or appear as black or red dots. This has no effect on the recorded image and does not constitute a malfunction. This product has been shipped enabled for power management: •... -
Page 8: Taking Care Of Your Vision
Taking care of your vision Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly focused screens, very small typefaces and low-contrast displays could stress your eyes. The following sections provide suggestions on how to reduce eyestrain. Eyes •... -
Page 9: Declaration Of Conformity
Declaration of Conformity Acer Incorporated 8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan Contact Person: Mr. Easy Lai, E-mail: easy_lai@acer.com.tw And, Acer Italy s.r.l Via Lepetit, 40, 20020 Lainate (MI) Italy Tel: +39-02-939-921 ,Fax: +39-02 9399-2913 www.acer.it... -
Page 10: Federal Communications Commission Declaration Of Conformity
Name of Responsible Party: Address of Responsible Party: Contact Person: Phone No.: Fax No.: Acer America Corporation 333 West San Carlos St., San Jose LCD Monitor S200HL S200HL xxxxxx (“x” = 0~9, a ~ z, A ~ Z or Blank) Acer America Corporation 333 West San Carlos St. - Page 11 15-pin color display signal cable 24-pin color display signal cable Standard timing table Installation Users controls Panel controls Using the Shortcut Menu Acer eColor Management Operation instructions Features and benefits Using the OSD Menus Picture Menu OSD Menu Setting Menu...
- Page 12 Troubleshooting VGA Mode DVI Mode (Optional)
- Page 13 Unpacking Please check that the following items are present when you unpack the box, and save the packing materials in case you need to ship or transport the monitor in the future. LCD monitor User guide Quick start guide DVI cable D-sub cable AC Power cord (Optional)
-
Page 14: Attaching The Base (For Selected Models)
Attaching the base (for selected models) Note: Remove the monitor and monitor base from its packaging. Carefully place the monitor face-down on a stable surface -- use a cloth to avoid scratching the screen. Attach the monitor stand arm to the base. Ensure that the base is locked onto the monitor stand arm. -
Page 15: Screen Position Adjustment
Screen position adjustment To optimize the viewing position, you can adjust the monitor tilt, using both of your hands to hold the edges of the monitor. The monitor can be adjusted to 15 degrees up or 5 degrees down. Connecting the adapter and AC Power cord •... -
Page 16: Display Data Channel (Ddc)
Display Data Channel (DDC) To make installation easier, so long as your system supports the DDC protocol, the monitor is able to plug-and-play. The DDC is a communication protocol through which the monitor automatically informs the host system about its capabilities; for example, supported resolutions and corresponding timing. - Page 17 24-pin color display signal cable PIN No. Description TMDS data 2- TMDS data 2+ TMDS data 2/4 shield DDC clock DDC data TMDS data 1- TMDS data 1+ TMDS data 1/3 shield PIN No. Description +5 V power DVI detect Hot-plug detection TMDS data 0- TMDS data 0+...
-
Page 18: Standard Timing Table
Standard timing table Mode VESA SVGA VESA VESA WXGA WXGA+ Resolution@Refresh Rate 640x480@60Hz 640x480@72Hz 640x480@75Hz 640x480@66.66Hz 720x400@70Hz 800x600@56Hz 800x600@60Hz 800x600@72Hz 800x600@75Hz 832x624@74.55Hz 1024x768@60Hz 1024x768@70Hz 1024x768@75Hz 1152x870@75Hz 1152x864@75Hz 1280x720@60Hz 1280x800@60Hz 1600x900@60Hz... -
Page 19: Installation
Installation To install the monitor on your host system, please follow the steps below: Steps Connect the video cable a Make sure both the monitor and computer are switched off. b Connect the VGA video cable to the computer. c Connect the digital cable (1) Make sure both the monitor and computer are switched off. -
Page 20: Panel Controls
OSD menu. Auto/Exit button • • Empowering Key Press this button to open the Acer eColor Management OSD and access the scenario modes. < > button to navigate to the desired function, > button to change the settings of the current function. -
Page 21: Acer Ecolor Management
Input sources that may be connected to your monitor. (Optional, only Dual-Input Model) Acer eColor Management Operation instructions 1 Press the Empowering Key to open the Acer eColor Management OSD menu and access the scenario modes. mpowering Technology User <... -
Page 22: Using The Osd Menus
Features and benefits Icon Mode type User mode ECO mode Standard mode Graphics mode Movie mode Using the OSD Menus Note: The following content is for general reference only. Actual product specifications may vary. Your LCD monitor is equipped with an on-screen display (OSD) menu for making various adjustments and settings. -
Page 23: Picture Menu
< > 2 Press the button to select Picture menu. The following options are available in the Picture menu: Acer ecolor Management, Brightness, Contrast, H. Position, V. Position, Focus, Clock, Colour Temp, and Auto Config. < > 3 Press the button to scroll through the Picture options, and press the Menu button to enter its sub-menu. -
Page 24: Setting Menu
OSD Menu The OSD menu is used for adjusting the OSD timeout setting. OSD Timeout 1 Press the Menu button to bring up the OSD menu. < > 2 Press the button to select OSD menu. 3 To adjust the OSD Timeout setting, press the Menu button to enter its sub-menu. <... -
Page 25: Information Menu
1 Press the Menu button to bring up the OSD menu. < > 2 Press the button to select Setting menu. The following options are available in the Setting menu: Wide Mode, DDC/CI, ACM, Input, Language, and Reset. < > button to scroll through the Setting options, and press the Menu 3 Press the button to enter its sub-menu. -
Page 26: Troubleshooting
Troubleshooting Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem. VGA Mode Problem LED status No picture visible Blue Blinking Blue Unstable picture Blue Abnormal picture Blue (Image is missing, off-center, too large or too small on the screen.) -
Page 27: Dvi Mode (Optional)
DVI Mode (Optional) Problem LED status No picture visible Blue Blinking Blue Remedy Using the OSD menu, adjust brightness and contrast to maximum or reset to their default settings. Check the power switch. Check if the AC power cord is properly connected to the monitor.