Advertisement
Precautions for installation
Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper
installation or operation inconsistent with this documentation.
The installation should comply with local electrical
code.
Before start the installation/connection, check and prepare
the required devices and cables. Before starting the con-
nection, turn the power of the devices including the camera
and the PC off.
Refer installation work to the dealer. Failure to
observe this may cause fire, electric shock, injury, or
damage to the product.
In order to prevent injury, the product must be
securely mounted to a wall according to installation
instruction.
Installation place
Salt damage prevention is applied to this product. However,
it is not completely anti-corrosive. Therefore, consider a
place for installation where direct splash of seawater can be
avoided. Especially when installing this product in a sea-
shore area or a place where a snow-melting agent is
applied, and also where rainwater is avoided, it is recom-
mended to regularly clean and rinse off salt with water. In
case of installing this product in a seashore area, regularly
check the status of equipment. (Replace the parts as
required.)
Power supply
Use a power supply device equipped with the ON-OFF
switch for servicing. When the power cord of the product is
connected to the power supply device, the power will be
supplied to the product. When the product is supplied, the
product will perform panning, tilting, zooming and focusing.
Before cleaning the product, make sure that the power
cable is not connected to the main power supply.
Installation area for this product
Consult the dealer about the installation area to select a
strong wall area.
• Screws used for installing this product on a wall are not
supplied. Considering the material and strength of the
area where the product is to be installed, prepare the
screws according to the total weight of the camera and
peripheral environment. Use the corrosion-resistant
screws, or apply caulking to the screws to be used for
fixing the framework and the adapter box.
Recommended screw*: M10 x 4 pcs.
Minimum pull-out strength (per 1 pc.): 823 N {185 lbf}
*When using "M8" screws, make sure to prepare 4 plain
washers and use them together.
• Do not mount the product on a plaster board or a
wooden section because they are too weak. If the prod-
uct is unavoidably mounted on such a section, the sec-
tion shall be sufficiently reinforced.
Mounting method for this product
This product is designed to be used as a pendant mount
camera. If the product is mounted on a desktop or at a
slant, it may not work correctly and its lifetime may be
shortened.
4
Protection from lightning
When cables are used outdoors, there is a chance that they
may be affected by lightning. In this case, install a lightning
arrester just before where the cables connect to the cam-
era.
Do not place this product in the following places:
• Locations where a chemical agent is used such as a
swimming pool
• Locations subject to moisture or oil smoke such as a
kitchen
• Locations that have a specific environment that is sub-
ject to an inflammable atmosphere or solvents
• Locations where radiation, x-ray, intense radio wave, or
strong magnetism is produced
• On the sea or locations where direct seawater splashes,
and where corrosive gas may be produced
• Locations subject to sulfur gas, such as a hot spring
area
• Locations where the temperature is not within the spec-
ified range (–50 °C to +55 °C {–58 °F to 131 °F})
• Locations subject to vibrations, such as on vehicles,
marine vessels, or above product lines (This product is
not designed for onvehicle use.)
• Locations subject to condensation as the result of
severe changes in temperature (In case of installing the
product in such locations, the dome cover may become
foggy or condensation may be caused on the cover.)
Screw tightening
• The screws and bolts must be tightened with an appro-
priate tightening torque according to the material and
strength of the installation area.
• Do not use an impact driver. Use of an impact driver
may damage the screws or cause tightening exces-
sively.
• When a screw is tightened, make the screw at a right
angle to the surface. After tightening the screws or
bolts, perform checks to ensure that the tightening is
sufficient enough so that there is no movement or
looseness.
The protection cover attached to the camera unit
shall be removed after completion of the installation.
(rain wash coating model)
Make sure to remove this product if it will no longer
be used.
Take notice of humidity.
Install this product when the humidity is low. If this product
is installed during rainfall or at a high humidity, the inside
may be exposed to moisture and the dome cover may
become foggy.
Matters you should know at installation work
Compatibility of devices are restricted. Before connections,
check the ratings and dimensions of the devices to be
used. Refer to the catalog or contact your dealer for further
information.
Advertisement
