Table of Contents
Advertisement
19MXR
left side of the mixer. Samples 4-6 are stored under Cue buttons 1-3 located on the right side of the board. The
Controller Mode Button LED will blink when the Sampler is active.
10. MASTER VOLUME LEVEL INDICATORS - The dual MASTER LEVEL LED indicators are used to detail the
master output level. The meters will detail the output level of both the left and right channels.
11. CUE MIXING CONTROL - This functions allows you to monitor the Cue level as well as the Program (main
output) level in your headphones. A channels Cue Level may only be monitored if the channels CUE (4) func-
tion is selected. To select a channels cue function press the CUE BUTTON (4) that is directly associated with
the specific channel you wish to monitor. You may use the mixing function to blend both the Cue level and the
Program level together. You can vary the output level to either hear more or less of either of the two levels.
Turning the Cue Mixing knob to the CUE position (left) will allow you to hear more of the Cue level. Turning the
knob to the PGM position (right) will allow you to hear more of the Program level (main output). You may also
use the Cue Mixing Control to hear either the Cue level or the Program level exclusively. If the knob is in the
full CUE position you will only hear the cue level, if the knob is in the full PGM position you will only hear the
main output. This function is especially useful when mixing without an monitor.
12. HEADPHONE JACK - This jack is used to connect your headphones to the mixer allowing you to monitor
the cue source. Use headphones only rated at 8 ohms to 32 ohms. Most DJ headphones are rated at 16 ohm,
these are highly recommended. Always be sure the CUE LEVEL VOLUME (6) is set to minimum before you put
the headphones on.
13. CHANNEL VOLUME FADER - These faders are used to control the output signal of any source assigned
to its particular channel. However, master volume is controlled by the MASTER VOLUME CONTROL (7).
14. FEATHER FADER PLUS CROSSFADER - This fader is used to blend the output signals of channels one
and two together. When the fader is in the full left position (channel 1), the output signal of channel one will be
controlled by the master volume level. The same fundamentals will apply for channel two. Sliding the fader from
one position to another will vary the output signals of channels one and two respectively. When the crossfader
is set in the center position, the output signals of both the channels one and channels two will be even.
15. FADER ASSIGN KNOB - This knob assigns a channel to the CROSSFADER (14). When a channel is
assigned to the left side of the CROSSFADER (14) that channels output level is routed to and controlled by the
CROSSFADER (14). Sliding the CROSSFADER (14) to left position will send the volume output of the assigned
channel to the MASTER VOLUME LEVEL (7), siding the CROSSFADER (14) to right position will cut that chan-
nels volume to MASTER VOLUME LEVEL (7). The reverse is true for the right channel fader assign switch. When
the assign switch is set to the "OFF" position the crossfader will have no function.
16. CROSSFADER CURVE ADJUSTMENT - This rotary knob is used to change the way the crossfader will
operate. The crossfader can operate in different modes, "NORMAL CURVE", "QUICK CURVE" or any variation
of the two. (Quick Curve usually used for scratching).
17. CUE, SYNC, PITCH BEND, & PLAY/PAUSE -
CUE 1, 2, & 3 - These buttons will set or trigger hot cue 1, 2, or 3.
DELETING HOT CUE POINTS - If a hot cue point is set, it is indicated by a lit Cue button LED. If you wish
to delete a hot cue point, press the Shift button. The shift button LED will flash along with the Cue LEDs.
Press the Cue button that contains the hot cue you wish to delete. After, press the Shift button again to
disable the soft shift..
PITCH BEND - To perform temporary pitch bends in Virtual DJ, hold the Shift button and Cue 1 to slow the
track. To speed up the track hold the Shift button and press the Cue 3 button. To reset the pitch, hold the
Shift button and press Cue 2.
SYNC - Will sync the selected deck to the opposite deck or master deck/tempo.
CUE - When the deck is playing, pressing this button will return to the 1st cue point. If the deck is
paused, pressing Cue will set a new cue point.
American Audio
- www.americanaudio.us - 19MXR Instruction Manual Page 11
©
®
CONTROLS AND FUNCTIONS cont.
Advertisement
Table of Contents
