Superior VRL4543ZEN Installation And Operation Instructions Manual page 18

o LIGHT Zone: LIGHT and light setting level is displayed
o FAN Zone: FAN and fan setting level is displayed
o TIME/PROG Zone: Current day indicator and current time is
displayed
o AUX Zone: Blank (AUX function is omitted on this control)
o FLAME Zone: A&B Flame Icons and flame setting level numbers
are displayed
Thermostat Disable Feature
• The Thermostat Mode (described above) may be enabled if de-
sired, but is disabled for applications where a thermostat is not
allowed or undesirable. THE FACTORY DEFAULT IS DISABLED.
• When Thermostat Mode is Disabled:
o The Modes of operation will cycle between MANUAL ON and
MANUAL OFF (omitting THERMO).
o Program Operation (described below) is also disabled.
o The SET TEMP zone will be blank.
o The room temperature will still be measured & displayed in the
ROOM TEMP Zone.
o The TIME/PROG zone will continue to display the Clock and Day
of week, but none of the icons associated with Program Mode
will be displayed.
• To disable or re-enable the Thermostat, the transmitter must be
in MANUAL OFF Mode, then press and hold the SET TEMP Zone
and the DOWN Button simultaneously for 10-seconds. The LCD
screen will go blank except either THERMO and OFF or THERMO
and ON will flash 3-times (0.5-seconds OFF, 0.5-seconds ON)
to indicate the change has been made
FLAME - A (OR MAIN) ADJUSTMENT
• Transmits a flame height setting command to the control module
to adjust the Flame-A height.
• Available settings are 1-7 with a factory default of 7. If the
Flame-A setting is changed during operation (either manu-
ally or automatically), the control will remember and use the
adjusted setting on subsequent manual ON cycles (Flame-A
setting memory).
• While in MANUAL ON, or PROGRAM ON modes, press the
FLAME Zone to enter Flame-A Adjustment, then press the UP or
DOWN buttons to raise and lower the flame; press the MODE/
SET Button or wait for 15 seconds to accept the new setting.
• LCD Display: When setting the Flame-A height, the Flame-A
icon, and Flame-A setting number will flash in the FLAME Zone.
18
REMOTE CONTROL OPERATION
LIGHT ADJUSTMENT
•
•
•
•
CONTINUOUS PILOT OPERATION
•
•
CHILD-LOCK OPERATION
•
•
•
SENSOR SAFETY OVERRIDE
•
•
•
•
•
COMMUNICATION SAFETY
•
SuperiorFireplaces.us.com
Continued
Transmits a light setting command to the control module to
adjust the light output level.
Available settings are 0 (off) – 6 with a factory default of 0 (off).
While in any mode of operation, press the LIGHT Zone to enter
Light Adjustment, then press the UP or DOWN buttons to raise
or lower the light output; press the MODE/SET Button or wait
for 15 seconds to accept the new setting.
LCD Displays:
• When raising or lowering the light output level with the UP
or DOWN buttons, the light icon and light setting number
will flash in the LIGHT Zone.
To activate or deactivate the Continuous Pilot Feature, press
and hold the MODE/SET and UP Buttons simultaneously for 5
seconds.
LCD Display: When activated, CONT. PILOT will be displayed in
the MODE Zone.
Child-Lock operation prevents any user input to the transmitter.
No mode of operation or feature may be adjusted when Child-
Lock is activated. All automatic functions will continue normally.
To activate or deactivate the Child-Lock feature, press and
hold the MODE/SET and DOWN Buttons simultaneously for 5
seconds.
LCD Displays:
• When activated, the LOCK icon will appear in the MODE
Zone.
• If any touch-zone or button is pressed when activated, the
LCD backlight will illuminate and the LOCK icon will flash
for 5 seconds in the MODE Zone.
Will only operate if the control is in MANUAL OFF mode.
Press and hold the FLAME Zone and the UP Button simultane-
ously activate the sensor safety override feature.
The module will ignore any sensor faults, continually emit an
igniter spark, and energize the PILOT operator output.
When the buttons are released, the control will immediately
return to MANUAL OFF mode.
LCD Display:
• When the Sensor Safety Override feature is activated, CONT.
PILOT will flash on the LCD screen.
In manual ON and program modes of operation, the transmitter
will send a communication safety transmission every 15 - min-
utes. This signal is further processed by the ignition control
module to verify the transmitter is communicating properly.
126861-01L