Comtrend Corporation AR-5319 User Manual
  1. Manuals
  2. Brands
  3. Comtrend Corporation Manuals
  4. Network Router
  5. AR-5319
  6. User manual
Comtrend Corporation AR-5319 User Manual

Comtrend Corporation AR-5319 User Manual

Adsl2+ wlan router
Hide thumbs
Table of Contents

Advertisement

Quick Links

AR-5319
ADSL2+ WLAN Router
User Manual
261056-079
Version A1.1, March 6, 2017

Advertisement

Table of Contents
loading

Related Manuals for Comtrend Corporation AR-5319

Summary of Contents for Comtrend Corporation AR-5319

  • Page 1 AR-5319 ADSL2+ WLAN Router User Manual 261056-079 Version A1.1, March 6, 2017...
  • Page 2 Preface This manual provides information related to the installation and operation of this device. The individual reading this manual is presumed to have a basic understanding of telecommunications terminology and concepts. If you find the product to be inoperable or malfunctioning, please contact technical support for immediate service by email at INT-support@comtrend.com For product update, new product release, manual revision, or software upgrades,...
  • Page 3 FCC & ISED User Information Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout changement ou modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur.
  • Page 4 Radiation Exposure 1. This Transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
  • Page 5 Copyright Copyright©2017 Comtrend Corporation. All rights reserved. The information contained herein is proprietary to Comtrend Corporation. No part of this document may be translated, transcribed, reproduced, in any form, or by any means without prior written consent of Comtrend Corporation.

  • Page 6: Table Of Contents

    Table of Contents CHAPTER 1 INTRODUCTION ......................8 CHAPTER 2 INSTALLATION ......................9 2.1 H ........................... 9 ARDWARE ETUP 2.2 F ..........................11 RONT ANEL CHAPTER 3 WEB USER INTERFACE .................... 13 3.1 D ........................13 EFAULT ETTINGS 3.2 IP C ........................
  • Page 7 6.1 A ....................... 65 DETECTION SETUP 6.2 S ............................70 ECURITY 6.2.1 IP Filtering ..........................70 6.2.2 MAC Filtering ........................73 6.3 Q S) ......................75 UALITY OF ERVICE 6.3.1 QoS Queue Setup ........................76 6.3.1.1 QoS Queue Configuration ....................76 6.3.2 Wlan Queue ...........................
  • Page 8 CHAPTER 9 LOGOUT ........................137 APPENDIX A - FIREWALL ......................138 APPENDIX B - PIN ASSIGNMENTS ....................141 APPENDIX C – SPECIFICATIONS ....................142 APPENDIX D - SSH CLIENT ......................144 APPENDIX E - CONNECTION SETUP ..................145 APPENDIX F - PRINTER SERVER ....................201...

  • Page 9: Chapter 1 Introduction

    USB Host, and is backward compatible with existing 802.11b (11Mbps) and 11g (54bps) equipment. The AR-5319 ADSL2+ router provides state of the art security features such as 64/128 bit WEP encryption and WPA2 encryption, Firewall, and VPN pass through.

  • Page 10: Chapter 2 Installation

    2.2 Front Panel for details). NOTE: If pressed down for more than 60 seconds, the AR-5319 will go into a firmware update state (CFE boot mode). The firmware can then be updated using an Internet browser pointed to the default IP address.
  • Page 11 Power ON Press the power button to the OFF position (OUT). Connect the power adapter to the power port. Attach the power adapter to a wall outlet or other AC source. Press the power button to the ON position (IN). If the Power LED displays as expected then the device is ready for setup (see section –...

  • Page 12: Front Panel

    2.2 Front Panel The front panel LED indicators are shown below and explained in the following table. This information can be used to check the status of the device and its connections. Color Mode Function The device is powered up. Green The device is powered down.
  • Page 13 Note: A malfunction is any error of internal sequence or state that will prevent the device from connecting to the DSLAM or passing customer data. This may be identified at various times such after power on or during operation through the use of self testing or in operations which result in a unit state that is not expected or should not occur.

  • Page 14: Chapter 3 Web User Interface

    3.2 IP Configuration DHCP MODE When the AR-5319 powers up, the onboard DHCP server will switch on. Basically, the DHCP server issues and reserves IP addresses for LAN devices, such as your PC. To obtain an IP address from the DCHP server, follow the steps provided below.
  • Page 15 STEP 4: Click OK to submit these settings. If you experience difficulty with DHCP mode, you can try static IP mode instead.
  • Page 16 STATIC IP MODE In static IP mode, you assign IP settings to your PC manually. Follow these steps to configure your PC IP address to use subnet 192.168.1.x. NOTE: The following procedure assumes you are running Windows. However, the general steps involved are similar for most operating systems (OS). Check your OS support documentation for further details.

  • Page 17: Login Procedure

    3.3 Login Procedure Perform the following steps to login to the web user interface. NOTE: The default settings can be found in 3.1 Default Settings. STEP 1: Start the Internet browser and enter the default IP address for the device in the Web address field.
  • Page 18 STEP 3: After successfully logging in for the first time, you will reach this screen. You can also reach this page by clicking on the following icon located at the top of the screen.

  • Page 19: Chapter 4 Device Information

    Chapter 4 Device Information You can reach this page by clicking on the following icon located at the top of the screen. The web user interface window is divided into two frames, the main menu (at left) and the display screen (on the right). The main menu has several options and selecting each of these options opens a submenu with more selections.

  • Page 20: Wan

    4.1 WAN Select WAN from the Device Info submenu to display the configured PVC(s). Heading Description Interface Name of the interface for WAN Description Name of the WAN connection Type Shows the connection type VlanMuxId Shows 802.1Q VLAN ID IPv6 Shows WAN IPv6 status Igmp Pxy Shows Internet Group Management Protocol (IGMP)

  • Page 21: Statistics

    4.2 Statistics This selection provides LAN, WAN, ATM and xDSL statistics. NOTE: These screens are updated automatically every 15 seconds. Click Reset Statistics to perform a manual update. 4.2.1 LAN Statistics This screen shows data traffic statistics for each LAN interface. Heading Description Interface...

  • Page 22: Wan Service

    4.2.2 WAN Service This screen shows data traffic statistics for each WAN interface. Heading Description Interface WAN interfaces Description WAN service label Received/Transmitted - Bytes Number of Bytes - Pkts Number of Packets - Errs Number of packets with errors - Drops Number of dropped packets...

  • Page 23: Xtm Statistics

    4.2.3 XTM Statistics The following figure shows ATM (Asynchronous Transfer Mode)/PTM (Packet Transfer Mode) statistics. XTM Interface Statistics Heading Description Port Number ATM PORT (0-3) In Octets Number of octets received over the interface Out Octets Number of octets transmitted over the interface In Packets Number of packets received over the interface Out Packets...

  • Page 24: Xdsl Statistics

    4.2.4 xDSL Statistics The xDSL Statistics screen displays information corresponding to the xDSL type. The two examples below (ADSL2 & ADSL2+) show this variation. ADSL2...
  • Page 25 ADSL2+ Click the Reset Statistics button to refresh this screen. Field Description Mode ADSL2, ADSL2+ Traffic Type ATM, PTM Status Lists the status of the DSL link Link Power State Link output power state. phyR Status Shows the status of PhyR™ (Physical Layer Re-Transmission) impulse noise protection Line Coding (Trellis) Trellis On/Off...
  • Page 26 In ADSL2 mode, the following section is inserted. MSGc Number of bytes in overhead channel message Number of bytes in Mux Data Frame Number of Mux Data Frames in FEC Data Frame Mux Data Frames over sync bytes Number of check bytes in FEC Data Frame Ratio of FEC over PMD Data Frame length Number of bits in PMD Data Frame The interleaver depth...
  • Page 27 Click Start to start the test or click Close to cancel the test. After the BER testing is complete, the pop-up window will display as follows.
  • Page 28 xDSL TONE GRAPH Click Draw Graph on the xDSL Statistics screen and a pop-up window will display the xDSL bits per tone status, as shown below.

  • Page 29: Route

    4.3 Route Choose Route to display the routes that the AR-5319 has found. Field Description Destination Destination network or destination host Gateway Next hop IP address Subnet Mask Subnet Mask of Destination Flag U: route is up !: reject route...

  • Page 30: Arp

    4.4 ARP Click ARP to display the ARP information. Field Description IP address Shows IP address of host pc Flags Complete, Incomplete, Permanent, or Publish HW Address Shows the MAC address of host pc Device Shows the connection interface 4.5 DHCP Click DHCP to display all DHCP Leases.
  • Page 31 Field Description IPv6 Address Shows IP address of device/host/PC MAC Address Shows the Ethernet MAC address of the device/host/PC Duration Shows leased time in hours Expires In Shows how much time is left for each DHCP Lease...

  • Page 32: Nat Session

    4.6 NAT Session This page displays all NAT connection session including both UPD/TCP protocols passing through the device. Click the “Show All” button to display the following. Field Description Source IP The source IP from which the NAT session is established Source Port The source port from which the NAT session is established Destination IP...

  • Page 33: Igmp Info

    4.7 IGMP Info Click IGMP Info to display the list of IGMP entries broadcasting through the IGMP proxy enabled WAN connection. Field Description Interface The Source interface from which the IGMP report was received The WAN interface from which the multicast traffic is received Groups The destination IGMP group address Member...

  • Page 34: Ipv6

    4.8 IPv6 4.8.1 IPv6 Info Click IPv6 Info to display the IPv6 WAN connection info. Field Description Interface WAN interface with IPv6 enabled Status Connection status of the WAN interface Address IPv6 Address of the WAN interface Prefix Prefix received/configured on the WAN interface Device Link-local Address The CPE's LAN Address Default IPv6 Gateway...

  • Page 35: Ipv6 Neighbor

    4.8.2 IPv6 Neighbor Click IPv6 Neighbor to display the list of IPv6 nodes discovered. Field Description IPv6 Address Ipv6 address of the device(s) found Flags Status of the neighbor device HW Address MAC address of the neighbor device Device Interface from which the device is located...

  • Page 36: Ipv6 Route

    4.8.3 IPv6 Route Click IPv6 Route to display the IPv6 route info. Field Description Destination Destination IP Address Gateway Gateway address used for destination IP Metric Metric specified for gateway Interface Interface used for destination IP...

  • Page 37: Cpu & Memory

    4.9 CPU & Memory Displays the system performance graphs. Shows the current loading of the CPU and memory usage with dynamic updates. Note: This graph is unavailable for Internet Explorer users.

  • Page 38: Network Map

    4.10 Network Map The network map is a graphical representation of router’s wan status and LAN devices. The feature is only available using a non-IE browser.

  • Page 39: Wireless

    4.11 Wireless 4.11.1 Station Info This page shows authenticated wireless stations and their status. Click the Refresh button to update the list of stations in the WLAN. Consult the table below for descriptions of each column heading. Field Description Lists the MAC address of all the stations. Associated Lists all the stations that are associated with the Access Point, along with the amount of time since packets were...

  • Page 40: Site Survey

    4.11.2 Site Survey The graph displays wireless APs found in your neighborhood by channel.

  • Page 41: Chapter 5 Basic Setup

    Chapter 5 Basic Setup You can reach this page by clicking on the following icon located at the top of the screen. 5.1 Layer 2 Interface Add or remove ATM, PTM and ETH WAN interface connections here. Click Add to create a new ATM interface (see Appendix E - Connection Setup).

  • Page 42: Wan Service Setup

    5.1.1 WAN Service Setup This screen allows for the configuration of WAN interfaces. Click the Add button to create a new connection. For connections on ATM or ETH WAN interfaces see Appendix E - Connection Setup. To remove a connection, select its Remove column radio button and click Remove. Heading Description Interface...

  • Page 43: Nat

    5.2 NAT To display this option, NAT must be enabled in at least one PVC. NAT is not an available option in Bridge mode. 5.2.1 Virtual Servers Virtual Servers allow you to direct incoming traffic from the WAN side (identified by Protocol and External port) to the internal server with private IP addresses on the LAN side.

  • Page 44: Port Triggering

    Field/Header Description Choose All Interface Virtual server rules will be created for all WAN interfaces. Choose One Interface Select a WAN interface from the drop-down menu. Use Interface Select a Service User should select the service from the list. Custom Service User can enter the name of their choice.
  • Page 45 Click Save/Apply to save and apply the settings. Consult the table below for field and header descriptions. Field/Header Description Use Interface Select a WAN interface from the drop-down box. Select an Application User should select the application from the list. Custom Application User can enter the name of their choice.

  • Page 46: Dmz Host

    5.2.3 DMZ Host The DSL router will forward IP packets from the WAN that do not belong to any of the applications configured in the Virtual Servers table to the DMZ host computer. To Activate the DMZ host, enter the DMZ host IP address and click Save/Apply. To Deactivate the DMZ host, clear the IP address field and click Save/Apply.

  • Page 47: Ip Address Map

    5.2.4 IP Address Map Mapping Local IP (LAN IP) to some specified Public IP (WAN IP). Field/Header Description Rule The number of the rule Type Mapping type from local to public Local Start IP The beginning of the local IP Local End IP The ending of the local IP Public Start IP...

  • Page 48: Alg/Pass Through

    5.2.5 ALG/Pass Through Supports ALG Pass-through for the listed protocols. To allow/deny the corresponding ALG protocol, select Enable / Disable and then click the Save button. After reboot, the protocol will be added/removed from the system module.

  • Page 49: Lan

    5.3 LAN Configure the LAN interface settings and then click Apply/Save. Consult the field descriptions below for more details. GroupName: Select an Interface Group. LAN INTERFACE IP Address: Enter the IP address for the LAN port. Subnet Mask: Enter the subnet mask for the LAN port. Enable IGMP Snooping: Enable by ticking the checkbox .
  • Page 50 Standard Mode: In standard mode, multicast traffic will flood to all bridge ports when no client subscribes to a multicast group – even if IGMP snooping is enabled. Blocking Mode: In blocking mode, the multicast data traffic will be blocked and not flood to all bridge ports when there are no client subscriptions to any multicast group.
  • Page 51 Select Enable DHCP Server Relay (not available if NAT enabled), and enter the DHCP Server IP Address. This allows the Router to relay the DHCP packets to the remote DHCP server. The remote DHCP server will provide the IP address. LAN INTERFACE To configure a secondary IP address, tick the checkbox ...

  • Page 52: Lan Ipv6 Autoconfig

    5.3.1 LAN IPv6 Autoconfig Configure the LAN interface settings and then click Save/Apply. Consult the field descriptions below for more details.
  • Page 53 LAN IPv6 Link-Local Address Configuration Heading Description EUI-64 Use EUI-64 algorithm to calculate link-local address from MAC address User Setting Use the Interface Identifier field to define a link-local address Static LAN IPv6 Address Configuration Heading Description Interface Address Configure static LAN IPv6 address and subnet prefix (prefix length is length required):...
  • Page 54 To remove an entry, tick the corresponding checkbox  in the Remove column and then click the Remove Entries button, as shown below. Heading Description Enable RADVD Enable use of router advertisement daemon RA interval Min(sec): Minimum time to send router advertisement RA interval Max(sec): Maximum time to send router advertisement Reachable Time(ms):...

  • Page 55: Static Ip Neighbor

    5.3.2 Static IP Neighbor Click the Add button to display the following. Click Apply/Save to apply and save the settings. Heading Description IP Version The IP version used for the neighbor device IP Address Define the IP Address for the neighbor device MAC Address The MAC Address of the neighbor device Associated Interface...

  • Page 56: Upnp

    5.3.3 UPnP Select the checkbox  provided and click Apply/Save to enable UPnP protocol.

  • Page 57: Wireless

    5.4 Wireless 5.4.1 Basic The Basic option allows you to configure basic features of the wireless LAN interface. Among other things, you can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements.
  • Page 58 Option Description Hide Access Select Hide Access Point to protect the access point from detection Point by wireless active scans. To view and connect to available wireless networks in Windows, open Connect to a Network by clicking the network icon ( ) in the notification area.

  • Page 59: Security

    5.4.2 Security The following screen appears when Wireless Security is selected. The options shown here allow you to configure security features of the wireless LAN interface. Click Apply/Save to implement new configuration settings. WIRELESS SECURITY Setup requires that the user configure these settings using the Web User Interface (see the table below).
  • Page 60 The settings for WPA2-PSK authentication are shown next. WEP Encryption This option specifies whether data sent over the network is encrypted. The same network key is used for data encryption and network authentication. Four network keys can be defined although only one can be used at any one time. Use the Current Network Key list box to select the appropriate network key.

  • Page 61: Parental Control

    5.5 Parental Control This selection provides WAN access control functionality. 5.5.1 Time Restriction This feature restricts access from a LAN device to an outside network through the device on selected days at certain times. Make sure to activate the Internet Time server synchronization as described in section 8.5 Internet Time, so that the...

  • Page 62: Url Filter

    5.5.2 URL Filter This screen allows for the creation of a filter rule for access rights to websites based on their URL address and port number. Select URL List Type: Exclude or Include. Tick the Exclude radio button to deny access to the websites listed. Tick the Include radio button to restrict access to only those listed websites.

  • Page 63: Home Networking

    5.6 Home Networking 5.6.1 Print Server This page allows you to enable or disable printer support. Please reference Appendix F to see the procedure for enabling the Printer Server.

  • Page 64: Dlna

    5.6.2 DLNA Enabling DLNA allows users to share digital media, like pictures, music and video, to other LAN devices from the digital media server. Insert USB drive to the USB host port on the back of router. Modify media library path to the corresponding path of the USB drive and click Apply/Save to enable the DLNA media server.

  • Page 65: Storage Service

    5.6.3 Storage Service This page displays storage devices attached to USB host. Display after storage device attached (for your reference).

  • Page 66: Chapter 6 Advanced Setup

    Chapter 6 Advanced Setup You can reach this page by clicking on the following icon located at the top of the screen. 6.1 Auto-detection setup The auto-detection function is used for CPE to detect WAN service for either ETHWAN or xDSL interface. The feature is designed for the scenario that requires only one WAN service in different applications.
  • Page 67 Enter the PPP username/password given by your service provider for PPP service detection.
  • Page 68 Select a LAN-as-WAN Ethernet port for auto-detect: Select the Ethernet Port that will be used as ETHWAN during auto-detection. WAN services list for ATM mode: A maximum of 7 WAN services with corresponding PVC are required to be configured for ADSL ATM mode. The services will be detected in order.
  • Page 69 Click "Apply/Save" to activate the auto-detect function. Options for each WAN service: These options are selectable for each WAN service. Users can pre-configure both WAN services and other provided settings to meet their deployed requirements. Auto Detection status and Restart The Auto-detection status is used to display the real time status of the Auto-detection feature.
  • Page 70 Auto Detection notice Note: The following description concerning ETHWAN is for multiple LAN port devices only. 1) This feature will automatically detect one WAN service only. If customers require multiple WAN services, manual configuration is required. 2) If a physical ETHWAN port is detected, the Auto Detection for ETHWAN will be fixed on the physical ETHWAN port and cannot be configured for any LAN port;...

  • Page 71: Security

    6.2 Security To display this function, you must enable the firewall feature in WAN Setup. For detailed descriptions, with examples, please consult Appendix A - Firewall. 6.2.1 IP Filtering This screen sets filter rules that limit IP traffic (Outgoing/Incoming). Multiple filter rules can be set and each applies at least one limiting condition.
  • Page 72 Field Description Filter Name The filter rule label IP Version Select from the drop down menu. Protocol TCP, TCP/UDP, UDP, or ICMP. Source IP address Enter source IP address. Source Port (port or port:port) Enter source port number or range. Destination IP address Enter destination IP address.
  • Page 73 Field Description Filter Name The filter rule label. IP Version Select from the drop down menu. Protocol TCP, TCP/UDP, UDP, or ICMP. Policy Permit/Drop packets specified by the firewall rule. Source IP address Enter source IP address. Source Port (port or port:port) Enter source port number or range.

  • Page 74: Mac Filtering

    Each network device has a unique 48-bit MAC address. This can be used to filter (block or forward) packets based on the originating device. MAC filtering policy and rules for the AR-5319 can be set according to the following procedure. The MAC Filtering Global Policy is defined as follows. FORWARDED means that all MAC layer frames will be FORWARDED except those matching the MAC filter rules.
  • Page 75 Click Save/Apply to save and activate the filter rule. Consult the table below for detailed field descriptions. Field Description Protocol Type PPPoE, IPv4, IPv6, AppleTalk, IPX, NetBEUI, IGMP Destination MAC Address Defines the destination MAC address Source MAC Address Defines the source MAC address Frame Direction Select the incoming/outgoing packet interface WAN Interfaces...

  • Page 76: Quality Of Service (Qos)

    6.3 Quality of Service (QoS) NOTE: QoS must be enabled in at least one PVC to display this option. (See Appendix E - Connection Setup for detailed PVC setup instructions). To Enable QoS tick the checkbox and select a Default DSCP Mark. Click Apply/Save to activate QoS.

  • Page 77: Qos Queue Setup

    6.3.1 QoS Queue Setup 6.3.1.1 QoS Queue Configuration Configure queues with different priorities to be used for QoS setup. In ATM mode, maximum 16 queues can be configured. In PTM mode, maximum 8 queues can be configured. For each Ethernet WAN interface, maximum 4 queues can be configured. To remove queues, check their remove-checkboxes (for user created queues), then click the Remove button.
  • Page 78 Name: Identifier for this Queue entry. Enable: Enable/Disable the Queue entry. Interface: Assign the entry to a specific network interface (QoS enabled). After selecting an Interface the following will be displayed. The precedence list shows the scheduler algorithm for each precedence level. Queues of equal precedence will be scheduled based on the algorithm.

  • Page 79: Wlan Queue

    6.3.2 Wlan Queue Displays the list of available wireless queues for WMM and wireless data transmit priority.

  • Page 80: Qos Classification

    6.3.3 QoS Classification The network traffic classes are listed in the following table. Click Add to configure a network traffic class rule and Enable to activate it. To delete an entry from the list, click Remove. This screen creates a traffic class rule to classify the upstream traffic, assign queuing priority and optionally overwrite the IP header DSCP byte.
  • Page 81 Field Description Traffic Class Name Enter a name for the traffic class. Rule Order Last is the only option. Rule Status Disable or enable the rule. Classification Criteria Ingress Interface Select an interface: (i.e. LAN, WAN, local, ETH1, ETH2, ETH3, wl0) Ether Type Set the Ethernet type (e.g.

  • Page 82: Routing

    6.4 Routing The following routing functions are accessed from this menu: Default Gateway, Static Route, Policy Routing and RIP. NOTE: In bridge mode, the RIP menu option is hidden while the other menu options are shown but ineffective. 6.4.1 Default Gateway Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is...

  • Page 83: Static Route

    6.4.2 Static Route This option allows for the configuration of static routes by destination IP. Click Add to create a static route or click Remove to delete a static route. After clicking Add the following will display. IP Version: Select the IP version to be IPv4. ...

  • Page 84: Policy Routing

    6.4.3 Policy Routing This option allows for the configuration of static routes by policy. Click Add to create a routing policy or Remove to delete one. On the following screen, complete the form and click Apply/Save to create a policy. Field Description Policy Name...

  • Page 85: Rip

    6.4.4 RIP To activate RIP, configure the RIP version/operation mode and select the Enabled checkbox  for at least one WAN interface before clicking Save/Apply.

  • Page 86: Dns

    6.5 DNS 6.5.1 DNS Server Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered. DNS Server Interfaces can have multiple WAN interfaces served as system dns servers but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected.

  • Page 87: Dynamic Dns

    Dynamic DNS The Dynamic DNS service allows you to map a dynamic IP address to a static hostname in any of many domains, allowing the AR-5319 to be more easily accessed from various locations on the Internet. To add a dynamic DNS service, click Add. The following screen will display.

  • Page 88: Dns Entries

    6.5.3 DNS Entries The DNS Entry page allows you to add domain names and IP address desired to be resolved by the DSL router. Choose Add or Remove to configure DNS Entry. The entries will become active after save/reboot. Enter the domain name and IP address that needs to be resolved locally, and click the Add Entry button.

  • Page 89: Dns Proxy/Relay

    6.5.4 DNS Proxy/Relay DNS proxy receives DNS queries and forwards DNS queries to the Internet. After the CPE gets answers from the DNS server, it replies to the LAN clients. Configure DNS proxy with the default setting, when the PC gets an IP via DHCP, the domain name, Home, will be added to PC’s DNS Suffix Search List, and the PC can access route with “Comtrend.Home”.

  • Page 90: Dsl

    6.6 DSL The DSL Settings screen allows for the selection of DSL modulation modes. For optimum performance, the modes selected should match those of your ISP. DSL Mode Data Transmission Rate - Mbps (Megabits per second) G.Dmt Downstream: 12 Mbps Upstream: 1.3 Mbps G.lite Downstream: 4 Mbps...

  • Page 91: Interface Grouping

    6.7 Interface Grouping Interface Grouping supports multiple ports to PVC and bridging groups. Each group performs as an independent network. To use this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button removes mapping groups, returning the ungrouped interfaces to the Default group.
  • Page 92 Automatically Add Clients With Following DHCP Vendor IDs: Add support to automatically map LAN interfaces to PVC's using DHCP vendor ID (option 60). The local DHCP server will decline and send the requests to a remote DHCP server by mapping the appropriate LAN interface. This will be turned on when Interface Grouping is enabled.
  • Page 93 If the onboard DHCP server is running on "Default" and the remote DHCP server is running on PVC 0/36 (i.e. for set-top box use only). LAN side clients can get IP addresses from the CPE's DHCP server and access the Internet via PPPoE (0/33). If a set-top box is connected to ETH1 and sends a DHCP request with vendor ID "Video", the local DHCP server will forward this request to the remote DHCP server.

  • Page 94: Ip Tunnel

    6.8 IP Tunnel 6.8.1 IPv6inIPv4 Configure 6in4 tunneling to encapsulate IPv6 traffic over explicitly-configured IPv4 links. Click the Add button to display the following. Options Description Tunnel Name Input a name for the tunnel Mechanism Mechanism used by the tunnel deployment Associated WAN Interface Select the WAN interface to be used by the tunnel Associated LAN Interface...

  • Page 95: Ipv4Inipv6

    6.8.2 IPv4inIPv6 Configure 4in6 tunneling to encapsulate IPv4 traffic over an IPv6-only environment. Click the Add button to display the following. Options Description Tunnel Name Input a name for the tunnel Mechanism Mechanism used by the tunnel deployment Associated WAN Interface Select the WAN interface to be used by the tunnel Associated LAN Interface Select the LAN interface to be included in the tunnel...

  • Page 96: Certificate

    6.9 Certificate A certificate is a public key, attached with its owner’s information (company name, server name, personal real name, contact e-mail, postal address, etc) and digital signatures. There will be one or more digital signatures attached to the certificate, indicating that these entities have verified that this certificate is valid.
  • Page 97 Field Description Certificate Name A user-defined name for the certificate. Common Name Usually, the fully qualified domain name for the machine. Organization Name The exact legal name of your organization. Do not abbreviate. State/Province Name The state or province where your organization is located. It cannot be abbreviated.

  • Page 98: Trusted Ca

    6.9.2 Trusted CA CA is an abbreviation for Certificate Authority, which is a part of the X.509 system. It is itself a certificate, attached with the owner information of this certificate authority; but its purpose is not encryption/decryption. Its purpose is to sign and issue certificates, in order to prove that these certificates are valid.

  • Page 99: Power Management

    6.10 Power Management This screen allows for control of hardware modules to evaluate power consumption. Use the buttons to select the desired option, click Apply and check the response.

  • Page 100: Multicast

    6.11 Multicast Input new IGMP or MLD protocol configuration fields if you want modify default values shown. Then click Apply/Save. Multicast Precedence: Select precedence of multicast packets. Multicast Strict Grouping Enforcement: Enable/Disable multicast strict grouping. Field Description Default Version Define IGMP using version with video server. Query Interval The query interval is the amount of time in seconds between IGMP General Query messages sent by the...
  • Page 101 Field Description Query Response Interval The query response interval is the maximum amount of time in seconds that the IGMP router waits to receive a response to a General Query message. The query response interval is the Maximum Response Time field in the IGMP v2 Host Membership Query message header.

  • Page 102: Wireless

    6.12 Wireless 6.12.1 Basic The Basic option allows you to configure basic features of the wireless LAN interface. Among other things, you can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements.
  • Page 103 Option Description Hide Access Select Hide Access Point to protect the access point from detection Point by wireless active scans. To view and connect to available wireless networks in Windows, open Connect to a Network by clicking the network icon ( ) in the notification area.

  • Page 104: Security

    6.12.2 Security The following screen appears when Wireless Security is selected. The options shown here allow you to configure security features of the wireless LAN interface. Click Apply/Save to implement new configuration settings. WIRELESS SECURITY Setup requires that the user configure these settings using the Web User Interface (see the table below).
  • Page 105 Select the Current Network Key and enter 13 ASCII characters or 26 hexadecimal digits for 128-bit encryption keys and enter 5 ASCII characters or 10 hexadecimal digits for 64-bit encryption keys. Choosing WPA2-PSK, you must enter WPA/WAPI passphrase and Group Rekey Interval.
  • Page 106 Encryption Strength This drop-down list box will display when WEP Encryption is enabled. The key strength is proportional to the number of binary bits comprising the key. This means that keys with a greater number of bits have a greater degree of security and are considerably more difficult to crack.

  • Page 107: Wps

    Apply/Save button. NOTES: Your client may or may not have the ability to provide security settings to the AR-5319. If it does not, then you must set the WPS AP mode to Configured. Consult the device documentation to check its capabilities.
  • Page 108 IIa. PUSH-BUTTON CONFIGURATION The WPS push-button configuration provides a semi-automated configuration method. The WiFi/WPS button on the front panel of the router can be used for this purpose. The WPS push-button configuration is described in the procedure below. It is assumed that the Wireless function is Enabled and that the router is configured as the Wireless Access Point (AP) of your WLAN.
  • Page 109 B - For Unconfigured mode, select Unconfigured from the Set WPS AP mode drop-down menu and click the Apply/Save button. Input the Device PIN displayed to your wireless client to initiate the PIN connection. Step 4: Activate the PIN function on the wireless client. For Configured mode, the client must be configured as an Enrollee.

  • Page 110: Mac Filter

    6.12.4 MAC Filter This option allows access to the router to be restricted based upon MAC addresses. To add a MAC Address filter, click the Add button shown below. To delete a filter, select it from the MAC Address table below and click the Remove button. Option Description Select...
  • Page 111 Enter the MAC address in the box provided and click Apply/Save.

  • Page 112: Wireless Bridge

    6.12.5 Wireless Bridge This screen allows for the configuration of wireless bridge features of the WIFI interface. See the table beneath for detailed explanations of the various options. Click Apply/Save to implement new configuration settings. Feature Description Bridge Restrict Selecting Disabled disables wireless bridge restriction, which means that any wireless bridge will be granted access.

  • Page 113: Advanced

    6.12.6 Advanced The Advanced screen allows you to configure advanced features of the wireless LAN interface. You can select a particular channel on which to operate, force the transmission rate to a particular speed, set the fragmentation threshold, set the RTS threshold, set the wakeup interval for clients in power-save mode, set the beacon interval for the access point, set XPress mode and set whether short or long preambles are used.
  • Page 114 Field Description Channel Drop-down menu that allows selection of a specific channel. Auto Channel Timer Auto channel scan timer in minutes (0 to disable) (min) 802.11n/EWC An equipment interoperability standard setting based on IEEE 802.11n Draft 2.0 and Enhanced Wireless Consortium (EWC) Bandwidth Select 20MHz or 20MHz/40MHz Mixed.
  • Page 115 Field Description RTS Threshold Request to Send, when set in bytes, specifies the packet size beyond which the WLAN Card invokes its RTS/CTS mechanism. Packets that exceed the specified RTS threshold trigger the RTS/CTS mechanism. The NIC transmits smaller packet without using RTS/CTS. The default setting of 2347 (maximum length) disables RTS Threshold.

  • Page 116: Chapter 7 Diagnostics

    Chapter 7 Diagnostics You can reach this page by clicking on the following icon located at the top of the screen. 7.1 Diagnostics – Individual Tests The first Diagnostics screen is a dashboard that shows overall connection status. Click the Diagnostics Menu item on the left side of the screen to display the individual connections.

  • Page 117: Ethernet Oam

    7.2 Ethernet OAM The Ethernet OAM (Operations, Administration, Management) page provides settings to enable/disable 802.3ah, 802.1ag/Y1.731 OAM protocols. To enable Ethernet Link OAM (802.3 ah), click Enabled to display the full configuration list. At least one option must be enabled for 802.1ah. WAN Interface Select layer 2 WAN interface for outgoing OAM packets OAM ID...
  • Page 118 To enable Ethernet Service OAM (802.1ag/Y1731), click Enabled to display the full configuration list. Click Apply/Save to implement new configuration settings. WAN Interface Select from the list of WAN Interfaces to send OAM packets MD Level Maintenance Domain Level MD Name Maintenance Domain name MA ID Maintenance Association Identifier...

  • Page 119: Uptime Status

    7.3 Uptime Status This page shows System, DSL, ETH and Layer 3 uptime. If the DSL line, ETH or Layer 3 connection is down, the uptime will stop incrementing. If the service is restored, the counter will reset and start from 0. A Bridge interface will follow the DSL or ETH timer.

  • Page 120: Ping

    7.4 Ping Input the IP address/hostname and click the Ping button to execute ping diagnostic test to send the ICMP request to the specified host.

  • Page 121: Trace Route

    7.5 Trace Route Input the IP address/hostname and click the TraceRoute button to execute the trace route diagnostic test to send the ICMP packets to the specified host.

  • Page 122: Chapter 8 Management

    Chapter 8 Management You can reach this page by clicking on the following icon located at the top of the screen. The Management menu has the following maintenance functions and processes: 8.1 Settings This includes Backup Settings, Update Settings, and Restore Default screens.

  • Page 123: Update Settings

    8.1.2 Update Settings This option recovers configuration files previously saved using Backup Settings. Press Browse… to search for the file, or enter the file name (including folder path) in the File Name box, and then click Update Settings to recover settings.

  • Page 124: Restore Default

    PC IP configuration to match any new settings. NOTE: This entry has the same effect as the Reset button. The AR-5319 board hardware and the boot loader support the reset to default. If the Reset button is continuously pressed for more than 10 seconds, the boot loader...

  • Page 125: System Log

    8.2 System Log This function allows a system log to be kept and viewed upon request. Follow the steps below to configure, enable, and view the system log. STEP 1: Click Configure System Log, as shown below (circled in Red). STEP 2: Select desired options and click Apply/Save.
  • Page 126 “Emergency” down to this configured level will be recorded to the log buffer on the AR-5319 SDRAM. When the log buffer is full, the newer event will wrap up to the top of the log buffer and overwrite the old event.

  • Page 127: Snmp Agent

    8.3 SNMP Agent Simple Network Management Protocol (SNMP) allows a management application to retrieve statistics and status from the SNMP agent in this device. Select the Enable radio button, configure options, and click Save/Apply to activate SNMP.

  • Page 128: Client

    8.4 TR-069 Client WAN Management Protocol (TR-069) allows an Auto-Configuration Server (ACS) to perform auto-configuration, provision, collection, and diagnostics to this device. Select desired values and click Apply/Save to configure TR-069 client options. The table below is provided for ease of reference. Option Description Enable TR-069...
  • Page 129 Option Description ACS Password Password used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This password is used only for HTTP-based authentication of the CPE. WAN Interface used Choose Any_WAN, LAN, Loopback or a configured by TR-069 client connection.

  • Page 130: Internet Time

    8.5 Internet Time This option automatically synchronizes the router time with Internet timeservers. To enable time synchronization, tick the corresponding checkbox , choose your preferred time server(s), select the correct time zone offset, and click Apply/Save. NOTE: Internet Time must be activated to use Parental Control.

  • Page 131: Access Control

    8.6 Access Control 8.6.1 Accounts This screen is used to configure the user account access passwords for the device. Access to the AR-5319 is controlled through the following user accounts:  The root account has unrestricted access to view and change the configuration of your Broadband router.
  • Page 132 Note: Passwords may be as long as 16 characters but must not contain a space. Click Save/Apply to continue.

  • Page 133: Services

    8.6.2 Services The Services option limits or opens the access services over the LAN or WAN. These access services available are: FTP, HTTP, ICMP, SNMP, TELNET and TFTP. Enable a service by selecting its dropdown listbox. Click Apply/Save to activate.

  • Page 134: Ip Address

    8.6.3 IP Address The IP Address Access Control mode, if enabled, permits access to local management services from IP addresses contained in the Access Control List. If the Access Control mode is disabled, the system will not validate IP addresses for incoming packets.

  • Page 135: Wake-On-Lan

    8.7 Wake-on-LAN This tool allows you to wake up (power on) computers connected to the Broadband Router LAN interface by sending special "magic packets". The network interface card in the computer or device that is going to be woken up must support Wake-on-LAN.

  • Page 136: Update Software

    8.8 Update Software This option allows for firmware upgrades from a locally stored file. STEP 1: Obtain an updated software image file from your ISP. STEP 2: Select the configuration from the drop-down menu. Configuration options: No change – upgrade software directly. Erase current config –...

  • Page 137: Reboot

    8.9 Reboot To save the current configuration and reboot the router, click Reboot. NOTE: You may need to close the browser window and wait for 2 minutes before reopening it. It may also be necessary, to reset your PC IP configuration.

  • Page 138: Chapter 9 Logout

    Chapter 9 Logout To log out from the device simply click the following icon located at the top of your screen. When the following window pops up, click the OK button to exit the router. Upon successful exit, the following message will be displayed.

  • Page 139: Appendix A - Firewall

    Appendix A - Firewall STATEFUL PACKET INSPECTION Refers to an architecture, where the firewall keeps track of packets on each connection traversing all its interfaces and makes sure they are valid. This is in contrast to static packet filtering which only examines a packet based on the information in the packet header.
  • Page 140 Example 1: Filter Name : In_Filter1 Protocol : TCP Policy : Allow Source IP Address : 210.168.219.45 Source Subnet Mask : 255.255.0.0 Source Port : 80 Dest. IP Address : NA Dest. Subnet Mask : NA Dest. Port : NA Selected WAN interface : br0 This filter will ACCEPT all TCP packets coming from WAN interface “br0”...
  • Page 141 00:34:12:78:90:56. All other frames on this interface are dropped. DAYTIME PARENTAL CONTROL This feature restricts access of a selected LAN device to an outside Network through the AR-5319 , as per chosen days of the week and the chosen times. Example: User Name...

  • Page 142: Appendix B - Pin Assignments

    Appendix B - Pin Assignments ETHERNET Ports (RJ45) ETHERNET LAN Ports (10/100Base-T) Table 1 Definition Definition Transmit data+ Transmit data- Receive data- Receive data+ Signals for ETHERNET WAN port (10/1001000Base-T) Table 2 Signal name Signal definition TRD+(0) Transmit/Receive data 0 (positive lead) TRD-(0) Transmit/Receive data 0 (negative lead) TRD+(1)

  • Page 143: Appendix C - Specifications

    Appendix C – Specifications Hardware Interface RJ-11 X 1 for ADSL  RJ-45 X 4 for LAN (10/100 Base-T auto-sense)  WPS/Wi-Fi Button X 1  On/Off Button X 1  Reset Button X 1  USB Host X 1 ...
  • Page 144 Operating temperature ......0 ~ 40 degrees Celsius Humidity…………………….10 ~ 90% (non-condensing, standard operating) Dimensions ........173 mm (W) x 39 mm (H) x 135.8 mm (D) Certifications........CE Kit Weight (1*AR-5319, 1*RJ11 cable, 1*RJ45 cable, 1*power adapter, 1*CD-ROM) NOTE: Specifications are subject to change without notice...

  • Page 145: Appendix D - Ssh Client

    Appendix D - SSH Client Unlike Microsoft Windows, Linux OS has a ssh client included. For Windows users, there is a public domain one called “putty” that can be downloaded from here: http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html To access the ssh client you must first enable SSH access for the LAN or WAN from the Management ...

  • Page 146: Appendix E - Connection Setup

    LAN/WAN interfaces. E1.1 ATM Interfaces Follow these procedures to configure an ATM interface. NOTE: The AR-5319 supports up to 16 ATM interfaces. STEP 1: Go to Basic Setup  WAN Setup  Select ATM Interface from the drop-down menu.
  • Page 147 This table is provided here for ease of reference. Heading Description Interface WAN interface name. ATM VPI (0-255) ATM VCI (32-65535) DSL Latency {Path0}  portID = 0 Category ATM service category Peak Cell Rate Maximum allowed traffic rate for the ATM PCR service connection Sustainable Cell The average allowable, long-term cell transfer rate on the VBR...
  • Page 148 There are many settings here including: VPI/VCI, DSL Link Type, Encapsulation Mode, Service Category and Quality of Service. Here are the available encapsulations for each xDSL Link Type:  EoA- LLC/SNAP-BRIDGING, VC/MUX  PPPoA- VC/MUX, LLC/ENCAPSULATION  IPoA- LLC/SNAP-ROUTING, VC MUX STEP 3: Click Apply/Save to confirm your choices.
  • Page 149 To add a WAN connection go to E2 ~ WAN Connections.
  • Page 150 E1.2 PTM Interfaces Follow these procedures to configure a PTM interface. NOTE: The AR-5319 supports up to four PTM interfaces. STEP 1: Go to Basic Setup  WAN Setup  Select PTM Interface from the drop-down menu. This table is provided here for ease of reference.
  • Page 151 Default PTM interface Quality of Service can be configured here, including Scheduler, Queue Weight and Rate Limit. STEP 3: Click Apply/Save to confirm your choices. On the next screen, check that the PTM interface is added to the list. For example, an PTM interface in Default Mode is shown below. To add a WAN connection go to section E2 WAN Connections.
  • Page 152 E1.3 ETHERNET Interfaces Follow these procedures to configure a PTM interface. STEP 1: Go to Basic Setup  WAN Setup  Select ETHERNET Interface from the drop-down menu. This table is provided here for ease of reference. Heading Description Interface/ (Name) WAN interface name.
  • Page 153 STEP 3: Select an Ethernet port and Click Apply/Save to confirm your choices. On the next screen, check that the ETHERNET interface is added to the list.
  • Page 154 E2 ~ WAN Connections The AR-5319 supports one WAN connection for each interface, up to a maximum of 16 connections. To setup a WAN connection follow these instructions. STEP 1: Go to Basic Setup  WAN Setup. STEP 2: Click Add to create a WAN connection. The following screen will display.
  • Page 155 STEP 3: Choose a layer 2 interface from the drop-down box and click Next. The WAN Service Configuration screen will display as shown below. NOTE: The WAN services shown here are those supported by the layer 2 interface you selected in the previous step. If you wish to change your selection click the Back button and select a different layer 2 interface.
  • Page 156 (10) IPoA – IPv6 (Not Supported) The subsections that follow continue the WAN service setup procedure.
  • Page 157 E2.1 PPP over ETHERNET (PPPoE) – IPv4 STEP 1: Select the PPP over Ethernet radio button and click Next. You can also enable IPv6 by ticking the checkbox  at the bottom of this screen. For tagged service, enter valid 802.1P Priority and 802.1Q VLAN ID. For untagged service, set -1 to both 802.1P Priority and 802.1Q VLAN ID Select a TPID if VLAN tag Q-in-Q is used.
  • Page 158 The settings shown above are described below. PPP SETTINGS The PPP Username, PPP password and the PPPoE Service Name entries are dependent on the particular requirements of the ISP. The user name can be a maximum of 256 characters and the password a maximum of 32 characters in length.
  • Page 159 DIAL ON DEMAND The AR-5319 can be configured to disconnect if there is no activity for a period of time by selecting the Dial on demand checkbox . You must also enter an inactivity timeout period in the range of 1 to 4320 minutes.
  • Page 160 When Enabled, this creates local PPPoE connections to the WAN side. Enable this option only if all LAN-side devices are running PPPoE clients, otherwise disable it. The AR-5319 supports pass-through PPPoE sessions from the LAN side while simultaneously running a PPPoE client from non-PPPoE LAN devices.
  • Page 161 STEP 4: Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered.
  • Page 162 E2.2 IP over ETHERNET (IPoE) – IPv4 STEP 1: Select the IP over Ethernet radio button and click Next. For tagged service, enter valid 802.1P Priority and 802.1Q VLAN ID. For untagged service, set -1 to both 802.1P Priority and 802.1Q VLAN ID Select a TPID if VLAN tag Q-in-Q is used.
  • Page 163 STEP 2: The WAN IP settings screen provides access to the DHCP server settings. You can select the Obtain an IP address automatically radio button to enable DHCP (use the DHCP Options only if necessary). However, if you prefer, you can instead use the Static IP address method to assign WAN IP address, Subnet Mask and Default Gateway manually.
  • Page 164 STEP 3: This screen provides access to NAT, Firewall and IGMP Multicast settings. Enable each by selecting the appropriate checkbox . Click Next to continue or click Back to return to the previous step. ENABLE NAT If the LAN is configured with a private IP address, the user should select this checkbox .
  • Page 165 Enable WAN interface with base MAC Enable this option to use the router’s base MAC address as the MAC address for this WAN interface. STEP 4: To choose an interface to be the default gateway. Click Next to continue or click Back to return to the previous step. STEP 5: Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system.
  • Page 166 STEP 6: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen. To activate it you must reboot.
  • Page 167 E2.3 Bridging– IPv4 NOTE: This connection type is not available on the Ethernet WAN interface. STEP 1: Select the Bridging radio button and click Next. Allow as IGMP Multicast Source Click to allow use of this bridge WAN interface as IGMP multicast source. Allow as MLD Multicast Source Click to allow use of this bridge WAN interface as MLD multicast source.
  • Page 168 After clicking Apply/Save, the new service should appear on the main screen. To activate it you must reboot. Go to Management  Reboot and click Reboot. NOTE: If this bridge connection is your only WAN service, the AR-5319 will be inaccessible for remote management or technical support from the WAN.
  • Page 169 E2.4 PPP over ATM (PPPoA) – IPv4 STEP 1: Click Next to continue. STEP 2: On the next screen, enter the PPP settings as provided by your ISP. Click Next to continue or click Back to return to the previous step.
  • Page 170 PPP SETTINGS The PPP username and password are dependent on the requirements of the ISP. The user name can be a maximum of 256 characters and the password a maximum of 32 characters in length. (Authentication Method: AUTO, PAP, CHAP, or MSCHAP.)
  • Page 171 DIAL ON DEMAND The AR-5319 can be configured to disconnect if there is no activity for a period of time by selecting the Dial on demand checkbox . You must also enter an inactivity timeout period in the range of 1 to 4320 minutes.
  • Page 172 Fixed MTU Fixed Maximum Transmission Unit. The size (in bytes) of largest protocol data unit which the layer can pass onwards. This value is 1500 for PPPoA. ENABLE PPP DEBUG MODE When this option is selected, the system will put more PPP connection information into the system log.
  • Page 173 STEP 4: Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered.
  • Page 174 STEP 5: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen. To activate it you must reboot.
  • Page 175 E2.5 IP over ATM (IPoA) – IPv4 STEP 1: Click Next to continue. STEP 2: Enter the WAN IP settings provided by your ISP. Click Next to continue. STEP 3: This screen provides access to NAT, Firewall and IGMP Multicast settings. Enable each by selecting the appropriate checkbox .
  • Page 176 ENABLE NAT If the LAN is configured with a private IP address, the user should select this checkbox . The NAT submenu will appear in the Advanced Setup menu after reboot. On the other hand, if a private IP address is not used on the LAN side (i.e. the LAN side is using a public IP), this checkbox ...
  • Page 177 NOTE: If the DHCP server is not enabled on another WAN interface then the following notification will be shown before the next screen. STEP 5: Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered.
  • Page 178 STEP 6: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen. To activate it you must reboot.
  • Page 179 E2.6 PPP over ETHERNET (PPPoE) – IPv6 STEP 1: Select the PPP over Ethernet radio button. Then select IPv6 only from the drop-down box at the bottom off the screen and click Next. For tagged service, enter valid 802.1P Priority and 802.1Q VLAN ID. For untagged service, set -1 to both 802.1P Priority and 802.1Q VLAN ID.
  • Page 180 STEP 2: On the next screen, enter the PPP settings as provided by your ISP. Click Next to continue or click Back to return to the previous step. The settings shown above are described below.
  • Page 181 DIAL ON DEMAND The AR-5319 can be configured to disconnect if there is no activity for a period of time by selecting the Dial on demand checkbox . You must also enter an inactivity timeout period in the range of 1 to 4320 minutes.
  • Page 182 USE STATIC IPv6 ADDRESS Unless your service provider specially requires it, do not select this checkbox . If selected, enter the static IP address in the IPv6 Address field. Don’t forget to adjust the IP configuration to Static IP Mode as described in section 3.2 IP Configuration.
  • Page 183 When Enabled, this creates local PPPoE connections to the WAN side. Enable this option only if all LAN-side devices are running PPPoE clients, otherwise disable it. The AR-5319 supports pass-through PPPoE sessions from the LAN side while simultaneously running a PPPoE client from non-PPPoE LAN devices.
  • Page 184 STEP 3: Choose an interface to be the default gateway. Also, select a preferred WAN interface as the system default IPv6 gateway (from the drop- down box). Click Next to continue or click Back to return to the previous step. STEP 4: Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system.
  • Page 185 Click Next to continue or click Back to return to the previous step.
  • Page 186 STEP 5: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen.
  • Page 187 E2.7 IP over ETHERNET (IPoE) – IPv6 STEP 1: Select the IP over Ethernet radio button and click Next. Then select IPv6 only from the drop-down box at the bottom off the screen and click Next. For tagged service, enter valid 802.1P Priority and 802.1Q VLAN ID. For untagged service, set -1 to both 802.1P Priority and 802.1Q VLAN ID.
  • Page 188 STEP 2: The WAN IP settings screen provides access to the DHCP server settings. You can select the Obtain an IP address automatically radio button to enable DHCP (use the DHCP Options only if necessary). However, if you prefer, you can use the Static IP address method instead to assign WAN IP address, Subnet Mask and Default Gateway manually.
  • Page 189 DHCP6C FOR ADDRESS ASSIGNMENT (IANA) The Internet Assigned Numbers Authority (IANA) is a department of ICANN responsible for coordinating some of the key elements that keep the Internet running smoothly. Whilst the Internet is renowned for being a worldwide network free from central coordination, there is a technical need for some key parts of the Internet to be globally coordinated, and this coordination role is undertaken by IANA.
  • Page 190 STEP 3: This screen provides access to NAT, Firewall and IGMP Multicast settings. Enable each by selecting the appropriate checkbox . Click Next to continue or click Back to return to the previous step. ENABLE NAT If the LAN is configured with a private IP address, the user should select this checkbox .
  • Page 191 STEP 4: To choose an interface to be the default gateway. Also, select a preferred WAN interface as the system default IPv6 gateway (from the drop-down box). Click Next to continue or click Back to return to the previous step.
  • Page 192 STEP 5: Select DNS Server Interface from available WAN interfaces OR enter Static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered. Select the configured WAN interface for IPv6 DNS server information OR enter the static IPv6 DNS server Addresses.
  • Page 193 STEP 6: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen.
  • Page 194 E2.8 PPP over ATM (PPPoA) – IPv6 STEP 1: Select IPv6 Only from the drop-down box at the bottom of this screen and click Next.
  • Page 195 STEP 2: On the next screen, enter the PPP settings as provided by your ISP. Click Next to continue or click Back to return to the previous step.
  • Page 196 DIAL ON DEMAND The AR-5319 can be configured to disconnect if there is no activity for a period of time by selecting the Dial on demand checkbox . You must also enter an inactivity timeout period in the range of 1 to 4320 minutes.
  • Page 197 USE STATIC IPv6 ADDRESS Unless your service provider specially requires it, do not select this checkbox . If selected, enter the static IP address in the IPv6 Address field. Don’t forget to adjust the IP configuration to Static IP Mode as described in section 3.2 IP Configuration.
  • Page 198 LAUNCH DHCP6C FOR RAPID COMMIT Rapid-Commit; is the process (option) in which a Requesting Router (DHCP Client) obtains "configurable information" (configurable parameters) from a Delegating Router (DHCP Server) by using a rapid DHCPv6 two-message exchange. The messages that are exchanged between the two routers (RR and DR) are called the DHCPv6 "SOLICIT"...
  • Page 199 STEP 3: Choose an interface to be the default gateway. Click Next to continue or click Back to return to the previous step.
  • Page 200 STEP 4: Select DNS Server Interface from available WAN interfaces OR enter Static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered. Select the configured WAN interface for IPv6 DNS server information OR enter the static IPv6 DNS server Addresses.
  • Page 201 STEP 5: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen.

  • Page 202: Appendix F - Printer Server

    Appendix F - Printer Server These steps explain the procedure for enabling the Printer Server. NOTE: This function only applies to models with an USB host port. STEP 1: Enable Print Server from Web User Interface. Select the Enable on-board print server checkbox ...
  • Page 203 STEP 2: Click the Windows start button.  Then select Control Panel.
  • Page 204 STEP 3: Select Devices and Printers. STEP 4: Select Add a printer.
  • Page 205 STEP 5: Select Add a network, wireless or Bluetooth printer. STEP 6: Click the Stop button.  Select The printer that I want isn’t listed.
  • Page 206 STEP 7: Choose Select a shared printer by name. Then input the printer link and click Next. http://LAN IP:631/printers/the name of the printer NOTE: The printer name must be the same name inputted in the WEB UI “printer server settings” as in step 1. STEP 8: Select the manufacturer ...
  • Page 207 STEP 9: The printer has been successfully installed. Click the Next button. STEP 10: Click Finish (or print a test page if required).
  • Page 208 STEP 11: Go to  Control Panel  All Control Panel Items  Devices and Printers to confirm that the printer has been configured.

Table of Contents