Remote Operation For All Models Except Chfpv-20 - Caesar Fireplace CHFP-002 Installation And Operating Instructions Manual

F. To change brightness, press the DIMMER
will show "L1" to "L5" when pressing this button.
G . To change flame speed, press the SPEED
show "V1" to "V5" when pressing this button.
H. Under the unlock mode
(
set for low heat 750W ,
indicator will show
indicator will show OF
I. Press "TIMER"
ranges from 1 to 8 hours, which will be shown on the indicator from "1H" to "8H". Timer is turned off when the
indicator shows "0H". If the appliance is restarted, timer also needs to be reset again.
J. When you turn on the appliance, all the backlight will be lighted up. Do not press any button for 20 seconds, all
the backlight will be off.
K. Press the "ON/OFF"

7.2.2.2 REMOTE OPERATION FOR ALL MODELS EXCEPT CHFPV-20

A . Plug in your electric appliance.
B . Press POWER " "
C . The ON/OFF" "
button activates the power to the appliance. Long press this button for 6 seconds, then
after a beep, heating function will be locked. Also long-press for 6 seconds again to unlock
heating function.
D-1 To change flame color, press the "FLAME .
red, yellow, blue, white, red & yellow, red & blue, red & white, yellow & blue, yellow & white,
blue & white, red & yellow & blue, multicolor
changing colors. When you press the button for 3 seconds until you hear a beep the indicator will show digital
"0" the flame color and brightness will be changed automatically. (For CHFP-002, CHFP-××B, CHFP-74BS,
,
SCI, and CHFPN series)
D-2 To change flame color, press the "FLAME .
white, and multicolor.
for 3 seconds until you hear a beep the indicator will show digital "0" the flame color and brightness will be
changed automatically. (For SCW series)
E-1 . To change flame bed color, press the "FLAME BED
green, blue, purple, cyan, yellow, orange, saffron, golden, verdant, and lavender.
"1" to "9" and "A" to "C" when changing colors. When you press the button for 3 second until you hear a
beep the indicator will show digital "0" the flame bed color and brightness will be changed automatically.
,
(For CHFP-002, CHFP-××B, CHFP-74BS, SCI, and CHFPN series)
E-2 To change flame bed color, press the "FLAME BED .
white, and multicolor.
for 3 seconds until you hear a beep the indicator will show digital "0" the flame bed color and brightness will be
changed automatically. (For SCW series)
19
"
"
, to activate the heater press the HEAT
) the indicator will show
"--". Press it for the third time, then the mechanism will stop function. After 10 seconds,
" ".
button, this sets the timing for switching the fireplace off automatically. The timer
buttom to turn off the appliance.
button at " " side, the appliance is on standby mode.
button can be used to power up or down the appliance. Pressing this
Under the locked mode "HEAT"
,
The indicator will show digital "1" to "5" when changing colors. When you press the button
,
,
The indicator will show digital "1" to "5" when changing colors. When you press the button
,
" button. There are
" button. There are 5 speeds to choose from
, " "
"-". To adjust the heat level press again for high heat (1500W ,
-
button is not available.
" button. There are 12 colors to choose from,
. The indicator will show digital "1" to "9" and "A" to "C" when
" button. There are 5 colors to choose from red, yellow, blue,
" button. There are 12 colors to choose from, red, white,
" button. There are 5 colors to choose from,
5 adjustments to choose from
.
button. The initial set-up heat level will be
,
,
,
The indicator will show digital
,
. The indicator
The indicator will
) the
the
red, yellow, blue,