Related Manuals for LITTLE BEAVER Kwik-Trench KT1200B
Summary of Contents for LITTLE BEAVER Kwik-Trench KT1200B
- Page 1 Kwik-Trench Mini-Trencher KT1200B OPERATORS MANUAL WITH MAINTENANCE AND PARTS INFORMATION 1.800.227.7515 LITTLEBEAVER.COM P.O. Box 840, Livingston, TX 77351 Phone: 936.327.3121 Fax: 936.327.4025 MFG BY: Little Beaver, Inc. 0418 sales@littlebeaver.com...
- Page 2 10 days after receipt of replacement parts. Be sure to prepay the shipping charges, we will not accept collect or COD packages. Our mailing address... LITTLE BEAVER, Inc. 2009 South Houston P. O. Box 840 Livingston, Texas 77351...
- Page 3 SAFETY ALERT SYMBOL The symbol shown above is used to call your attention to instructions concerning your personal safety. WATCH THIS SYMBOL — It points out important safety precautions. It means — ATTENTION! BECOME ALERT! YOUR PERSONAL SAFETY IS INVOLVED! Read the message that follows and be alert to the possibility of Personal Injury or Death! WARNING: The Engine Exhaust from this product contains chemicals known to...
- Page 4 TABLE OF CONTENTS OPERATORS MANUAL Page # Customer Service Information Safety Alert, Warranty and Machine Information Table of Contents Safety Instructions Maintenance and Lubrication, Clutch Maintenance and Lubrication, V-Belt Maintenance and Lubrication, V-Belt, Cutter Hub, Bearing Assembly O-10 Trenching Instructions PARTS MANUAL Page # P-1 &...
- Page 5 SAFETY INSTRUCTIONS DANGER: Failure to observe safety instructions and reasonable safety practices can cause Property Damage, Serious Bodily Injury and/or Death. BE CAREFUL!! WATCH OUT FOR BYSTANDERS!! DANGER: NEVER dig trenches where there is a possibility of underground power cables or other hazards.
- Page 6 MAINTENANCE and LUBRICATION DANGER: NEVER run engine inside building or enclosed area. Exhaust gases contain carbon monoxide, an odorless and deadly poison. Engines are shipped without oil or gasoline. Refer to MANUFACTURER'S INSTRUCTIONS for proper procedures and recommended fluids. IMPORTANT DO NOT drop the machine off the back of a vehicle, this may cause damage to the body and frame.
- Page 7 MAINTENANCE CONT... V-BELT CARE: V-belts may be the item most overlooked during equipment maintenance, but proper care and maintenance of V-belts and their sheaves (pulleys) can yield great rewards. The nature of V- belts makes preventive maintenance relatively easy. V-belts and sheaves wear gradually and usually give advance warning of failure.
- Page 8 V-BELT CARE CONT... Check the alignment of the sheaves. The drive and driven shafts should be parallel both horizon- tally and vertically, and the centers of both sheaves should be in a straight line. Although V-belts can tolerate minor misalignment (About 1/16 inch per 12 inches of shaft center distance), close- to-perfect alignment will prolong belt life.
- Page 9 TRENCHER ASSEMBLY INSTRUCTIONS: Remove the washers and pins that are on the front axles. Install two (2) front tires with valve stem facing out. Re-install washers & pins. Install rear tire by inserting axle bolt through wheel bearings and swivel. Install and tighten lock nut, leaving a small amount of play in wheel bear- ings.
- Page 10 TRENCHER OPERATING INSTRUCTIONS: Put trencher in position. Turn fuel on. Use choke when starting engine if necessary. Allow engine to warm up for 2-3 minutes, then bring engine speed up with the throttle. Stand behind the push handle and lower trencher by turning the crank handle counter-clock- wise to required depth.
- Page 11 PARTS INFORMATION NOTES:...
- Page 12 FRAME ASSEMBLY - KT1200B 15--- ---37 --- 45 ---13 44--- ---35 43 --- --- 46 \----39 --- 43 --- 41 37 --- 45 --- 19--- ---40 27--- ---32 33--- ---4 ---16 ---36 6--- 15--- ---7 ---3 15--- --17 ---15 31--- --22 ---1 37---...
- Page 13 FRAME ASSEMBLY KT1200B ITEM # PART # DESCRIPTION KT286 Push Handle Assy. (w/ handle grips) KT010 Handle Grips KT1264 Crank Handle Assy. (w/ handle grip) KT006 Swivel, U-Joint KT045 Actuator Complete, 8" KTAH812 Gear Head, Actuator KT045C Cylinder, Actuator, 8" KTAB812 Bevel Housing, Actuator KT009...
- Page 14 BELT DRIVE ASSEMBLY 1 4--- KT1200B 13--- ---21 17--- ---20 7--- ---8 ---15 ---16 B--- G--- ---F 1--- ---C ---D A--- 23-- D--- 22--- E--- 25--- ---22 ---24 Page P-3 1000...
- Page 15 BELT DRIVE ASSEMBLY KT1200B ITEM # PART # DESCRIPTION KT290 Top Hat Assy. KT242 Base, Top Hat KT249 Plate, Upper, Top Hat 30151 Nut, Hex, 1/2" NC 30153 Washer, Flat, 1/2" SAE 30158 Nut, Hex, 1/2 NC Nylon Lock KT248 Pin, Hinge 30163 Cotter Pin, 1/8"...
- Page 16 CLUTCH/CUTTER HUB ASSEMBLY Cutter Wheel collar should face the engine. See pages following for cutter wheel information. ITEM # PART # DESCRIPTION KT4-1032 Bolt, Socket Head Shoulder, 1/2 x 1 3/4 KT4-1031 Spring, Die KT4-1017 Friction Plate KT4-1029 Clutch Facing KT4-1026 Nylon Bearing KT4-1040...
- Page 17 KT1200B SUPER BLADE PLUS BLADE (SBP) ASSEMBLY SBSR 2" digging width SBSL SBSL ROTATION: Counter-Clockwise SBCIR PART # DESCRIPTION SBSR KT23S2 Cutter Wheel-2" width KT23S1 Cutter Wheel-1" width SBCIL SBCIL KTSBP-SR Tooth, Straight Right KTSBP-SL Tooth, Straight Left KTSBP-CIL Tooth, Curved in Left KTSBP-CIR Tooth, Curved in Right SBCIR SBSR...
- Page 18 KT1200B SUPER XTRA ROCK BLADE (SXRT) ASSEMBLY SXSR 2" digging width ROTATION: Counter-Clockwise SXCIL SXSL PART # DESCRIPTION KT23R2 Cutter Wheel-2" width KTSXRT-SR - Tooth, Straight Right KTSXRT-SL - Tooth, Straight Left KTSXRT-CIL - Tooth, Curved in Left KTSXRT-CIR - Tooth, Curved in Right SXCIR SXSL KTR122...
- Page 20 THINK SAFETY FIRST P.O. BOX 840 LIVINGSTON, TEXAS 77351 PH# 409/327-3121 FAX# 409/327-4025 Web: www.littlebeaver.com E-Mail: sales@littlebeaver.com...