Download Print this page

Sealey GSS3030G Instructions Manual

Galvanized steel shed green 3 x 3 x 2.1m

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to
when building this shed.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Keep children and unauthorised persons away from the working area.
DO NOT use the shed for any purpose other than that for which it is designed.
Use appropriate safety clothing including eye protection.
Note! The assembly of this product will require assistance.
2. INTRODUCTION
Galvanized steel panels easily assembled to form a rigid and secure gable roofed shed. Has double doors, which are secured by cross bolt and
eyelet that accepts a padlock (not included) for additional security. All models supplied with bolt-down fixing kits.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GSS3030G
Overall Size (W x D X H*). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000 x 3000 x 2100mm
Roof Type: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gable
*Minimum Wall Height
© Jack Sealey Limited
INSTRUCTIONS FOR:
GALVANIZED STEEL SHED GREEN
3 x 3 x 2.1m
GSS3030G
MODEL No:
Original Language Version
GSS3030G
Issue: 1 - 28/08/14

Advertisement

loading

Summary of Contents for Sealey GSS3030G

  • Page 1 Model No: ........
  • Page 2: Concrete Slab

    Check contents: Lay out all components with the part numbers facing upwards and check off against the parts lists on the next four pages. In the unlikely event of a missing component please contact your local Sealey dealer. Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 3 Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 4 Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 5 Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 6 Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 7: Parts Diagram

    7. PARTS DIAGRAM Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 8 (Any timber studding used will need to be the same length as the shed i.e. 3mtr). Trestles are available from your Sealey Dealer, Part No. FDT3. Attach the studding to trestles with equal overhang using nylon cable ties or similar ‘safe’ method.
  • Page 9 Ensure the panel is well supported when screwing the connector into place using four self tapping screws. The centre screw hole on the connector is not used at this stage. Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 10 35R and 35L to the panel with self tapping screws ensuring that you use a mid wall channel connector in the centre of the panel where the two channels meet. The open part of the channel should be facing downwards. Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 11 8.2.3. Assemble the other side panel in the same way. 8.3. ASSEMBLE THE ROOF PANELS. 8.3.1. Place 12R, 2 x 12m and 12L onto your work table and fix them together with self tapping screws. Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 12 8.3.4. Leave the four corners of the roof panel unfixed at this stage. Assemble the second roof panel in the same way. Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 13 13L and 13R using self tapping screws. (Note that screws are fixed to both sides of component 28, at the centre, in order to tie together the two bottom channels 27L & 27M). Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 14 28. 8.5. ASSEMBLE THE FRONT DOOR. 8.5.1. Fix barrel bolt 74 and plate 75 onto door 5L by rivetting them into place. Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 15 8.5.3. Close the doors and allow them to rest in the frame. Align the pad bolt (70) and keeper (71) with the pre-drilled holes in the doors and fix in place with the 16mm self tapping screws provided or alternatively, rivet in place. Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 16 8.6.1. Now fix the front, rear and side panels together using 4 self tapping screws at each corner. Fix a pair of gable panels 68R & 68L to both the front and rear walls of the shed using self tapping screws as shown below. Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 17 8.6.3. Take one roof panel and identify on which side of the panel the channels 27E and 27F are fixed. Slide or insert this side of the panel into one side of the ridge beam assembly that you have just created as indicated above. Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 18 (53), gable end & roof panel. At this stage, do not fix the 4 screws directly adjacent to the centre of the gable ends. Refering to the instructions in the diagram below, fix 2 roof braces inside the shed Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 19 (72) as shown above. Fix the keeper (71) to the inside of the lower door frame ensuring that it is aligned with the barrel bolt. Original Language Version © Jack Sealey Limited GSS3030G Issue: 1 - 28/08/14...
  • Page 20 Place the covers onto the ends of the screws where required and 'screw' them down until they are flush with the inside face of the shed. Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.