Related Manuals for Olympus IPLEX GAir
Summary of Contents for Olympus IPLEX GAir
- Page 1 Instruction for Remote Operation IPLEX GAir INDUSTRIAL ENDOSCOPE Industrial Endoscope MM4081 01...
-
Page 2: Table Of Contents
1-2-2 Setting the wired LAN port ................3 1-2-3 Connecting the units ..................4 1-2-4 Setting the repeater ..................4 1-3 Turning ON the power of the IPLEX GAir system ........9 1-4 Remote operation ..................9 1-5 Turning OFF the power of the IPLEX GAir system .........9 2 Operation with controling the power remotely .........10... - Page 3 IPLEX GAir This instrument can be operated away from the base unit using the repeater (T) and the repeater (R) (recommended products). Connecting units as follows allows you to operate this instrument remotely using the remote control unit while looking at the external monitor. ( “1 Operation without controling the...
-
Page 4: Operation Without Controling The Power Remotely
To check that the remote control unit is connected to the system properly, it is recommended to set the <REMOTE CONTROLLER VIBRATION> menu to <ON> in advance. (See “5.2 Using the live screen or freeze screen” in the instruction manual for IPLEX GAir.) Necessary items:... -
Page 5: Setting The Network Environment
IPLEX GAir 1-2 Setting the network environment The network environment described in this section must be configured for the first time only. It is not necessary to configure it for the second time and after. 1-2-1 Preparing IPInstaller Install IPInstaller. -
Page 6: Connecting The Units
1-2-3 Connecting the units Connect the base unit, repeater (T), repeater (R), external monitor, remote control unit, and setting PC as follows. NOTE: • Turn OFF the power of each unit. • Connect the repeater (T) to the HDMI terminal and the USB connector of the base unit. •... - Page 7 IPLEX GAir Press the [+] or [-] button to set the numerical characters in the ID Number field to “001”. Start IP Installer on the setting PC and check that the repeater is recognized properly. If the repeater is not recognized, check the connection of cables, etc.
- Page 8 Disconnect the LAN cable for setting the Network environment connected to the setting PC from the repeater (T), and connect it to the repeater (R). Remote side Operation side Repeater (T) Repeater (R) (recommended) (recommended) Wired LAN cable HDMI (Maximum 100 m) HDMI External monitor commercially-available...
- Page 9 IPLEX GAir Start IP Installer on the setting PC and check that the repeater is recognized properly. If the repeater is not recognized, check the connection of cables, etc. On the IP Installer screen, change the network settings of the repeater (R) as follows.
- Page 10 Click ▼ that appears when you place the mouse pointer on the VE8900R or the VE8950R, and click <Configuration>. The setting screen of the repeater (R) is displayed. Set as follows. Connected TX T001 Manual T001 Click <Save>. The setting screen is closed and the screen is returned to the system setting screen. Disconnect the LAN cable for setting the Network environment connected to the setting PC from the repeater (R).
-
Page 11: Turning On The Power Of The Iplex Gair System
IPLEX GAir 1-3 Turning ON the power of the IPLEX GAir system Turn ON the main switch of the drum unit. The [POWER] LED of the drum unit turns ON in orange. Press the [POWER] button of the base unit for approx. 1.5 to 2 seconds. -
Page 12: Operation With Controling The Power Remotely
To check that the remote control unit is connected to the system properly, it is recommended to set the <REMOTE CONTROLLER VIBRATION> menu to <ON> in advance. (See “5.2 Using the live screen or freeze screen” in the instruction manual for IPLEX GAir.) Necessary items:... -
Page 13: Setting The Network Environment
TIP: To return the power control to the initial setting, the SDHC card containing the program to return the power control to the initial setting is necessary. Contact Olympus for details. 2-2-2 Preparing IPInstaller Install IPInstaller. -
Page 14: Setting The Wired Lan Port
2-2-3 Setting the wired LAN port Start the setting PC, and set TCP/IP of the setting PC as follows. IP assignment Manual IP address setting (v4) 192.168.1.200 Subnet mask 255.255.0.0 Default gateway 192.168.1.254 TIP: The procedures to set ICP/IP are described below. 1. -
Page 15: Connecting The Units
IPLEX GAir 2-2-4 Connecting the units Connect the base unit, drum unit, repeater (T), repeater (R), external monitor, remote control unit, remote power control unit, and setting PC as follows. NOTE: • Turn OFF the power of each unit. • Connect the repeater (T) to the HDMI terminal and the USB connector of the base unit. -
Page 16: Setting The Repeater
On the IP Installer screen, change the network setting of the remote power con- trol unit as follows: IP address setting (v4) 192.168.1.100 Subnet mask 255.255.0.0 Default gateway 192.168.1.254 Check that the LEDs of Port1 and Port2 of the remote power control unit are turned ON in orange. - Page 17 IPLEX GAir Connect the power cord of the repeater (T) to the outlet. The numerical characters are displayed in the ID Number field . (It takes approximately one minute to display the numerical characters.) Tx/Rx Press the [+] or [-] button...
- Page 18 Close IPInstaller. Disconnect the LAN cable for setting the Network environment connected to the setting PC from the repeater (T), and connect it to the repeater (R). Operation side Remote side Continuous power supply Repeater (T) Repeater (R) (recommended) Wired LAN cable (recommended) HDMI (Maximum 100 m)
- Page 19 IPLEX GAir Press the [+] or [-] button to set the numerical characters in the ID Number field to “001”. TIP: The repeater (R) can be changed to the transmitter. Check that LED(Rx) of the repeater (R) is turned ON. If LED(Tx) of the transmitter is turned ON, press the Tx/Rx switch button to select Tx or Rx.
- Page 20 On the VE Manager screen of the repeater (R), check that the VE89x0T and the VE89x0R are displayed individually. Check that the repeater (T) and the repeater (R) are recognized individually. If the repeater is not recognized, check the network setting or the connection configuration of the devices.
- Page 21 IPLEX GAir Click <Save>. The setting screen is closed and the screen is returned to the system setting screen. Turn ON the power of the drum unit. Check that the system screen is displayed on the external monitor. Check that the system can be operated using the remote control unit.
-
Page 22: Remote Operation
2-3 Remote operation The system can be operated remotely using the remote control unit. TIP: The buttons are displayed on the external monitor, but the system cannot be operated by touching the external monitor. 2-4 Turning OFF the power remotely Press the [THUMBNAIL] button and the [CENT] button of the remote control unit for 2 seconds or more at the same time. -
Page 23: Turning On The Power Remotely
IPLEX GAir 2-5 Turning ON the power remotely Start the Web browser on the setting PC and access to the following address. http://192.168.1.100/ Even if the message telling you that the Website is not safe is displayed, continue the operation. - Page 24 Manufactured by Shinjuku Monolith, 2-3-1 Nishi-Shinjuku, Shinjuku-ku, Tokyo 163-0914, Japan Distributed by...