Bosch DRC99PS20 User Manual And Assembly Instructions page 9

Ceiling-mounted ventilation system
Hide thumbs Also See for DRC99PS20:
Table of Contents

Advertisement

The Home Connect services are not available in every
country. The availability of the Home Connect function
depends on the availability of Home Connect services
in your country. You can find information about this at:
www.home-connect.com.
To be able to use Home Connect, you must first set up
the connection to the WLAN home network (Wi-Fi
to the Home Connect app.
¡ Automatically connecting appliance to WLAN home
network (Wi-Fi) → Page 9
¡ Connecting appliance to WLAN home network (Wi-
Fi) manually → Page 9
The Home Connect app guides you through the entire
login process. Follow the instructions in the Home Con-
nect app to configure the settings.
If the appliance is not connected to your home net-
work, it functions as an appliance with no network con-
nection and can still be operated via the display.
Tips
¡ Please consult the documents supplied by
Home Connect.
¡ Please also follow the instructions in the Home Con-
nect app.
Notes
¡ Please note the safety precautions in this instruction
manual and make sure that they are also observed
when operating the appliance via the Home Con-
nect app.
→ "Safety", Page 2
¡ Operating the appliance on the appliance itself al-
ways takes priority. During this time it is not possible
to operate the appliance using the Home Connect
app.
¡ In networked standby mode, the appliance requires
a maximum of 2 W.
¡ If you need your device's MAC address to connect
to your home network, you can find this next to the
rating plate → Page 14 inside the appliance. To do
this, Remove the filter → Page 11.
Automatically connecting the
appliance to the WLAN home network
(Wi-Fi)
If your router has a WPS function, you can connect the
appliance to your WLAN home network (Wi-Fi) automat-
ically.
Note: The appliance cannot be switched on during the
connection process. Press ⁠
Requirements
¡ Wi-Fi on the router is activated.
¡ The appliance receives signals from the WLAN home
network (Wi-Fi) at its installation location.
¡ The Home Connect app is installed on your mobile
device.
¡ The appliance and the light are switched off.
Press and hold the ⁠  button until LED 7 flashes in
1.
the LED display.
Press ⁠ .
2.
a LED 1 and LED 7 flash in the LED display.
1
Wi-Fi is a registered trademark of the Wi-Fi Alliance.
1
) and
to cancel the process.
Press the WPS button on the router within the next
3.
2 minutes.
a If the connection has been established, the appli-
ance automatically connects to the Home Connect
app. LED 3 and LED 7 flash in the LED display.
If no connection can be established, the appliance
4.
automatically switches to the manual connection to
the home network, LED 2 and LED 7 flash in the
LED display. Log the appliance manually into the
home network or press ⁠
gin.
On your mobile device, follow the instructions for
5.
automatic network login.
a The login process is complete when LED 7 stops
flashing and remains continuously lit.
Manually connecting the appliance to
the WLAN home network (Wi-Fi)
Note: The appliance cannot be switched on during the
connection process. Press ⁠
Requirement: The appliance and the light are switched
off.
Press and hold the ⁠  button until LED 7 flashes in
1.
the LED display.
Press ⁠
twice to start logging into your home net-
2.
work manually.
a LED 2 and LED 7 flash in the LED display.
Follow the instructions in the app.
3.
a If the connection has been established, the appli-
ance automatically connects to the Home Connect
app. LED 3 and LED 7 light up in the LED display.
On your mobile device, follow the instructions for
4.
manually logging into your network.
a The login process is complete when LED 7 stops
flashing and remains continuously lit.
Connecting the appliance to the
Home Connect app
Requirements
¡ The Home Connect app is installed on your mobile
device.
¡ The Home Connect app is opened.
Press and hold the ⁠
1.
flash in the LED display.
Follow the instructions for the Home Connect app
2.
on the mobile device.
a The login process is complete when LED 7 stops
flashing and remains continuously lit.
Software update
Your appliance's software can be updated using the
software update function, e.g. for the purposes of op-
timisation, troubleshooting or security updates.
To do this, you must be a registered Home Con-
nect user, have installed the app on your mobile device
and be connected to the Home Connect server.
Home Connect  en
in order to restart the lo-
to cancel the process.
button until LED 3 and LED 7
9

Advertisement

Table of Contents
loading

This manual is also suitable for:

Drc99ps25

Table of Contents