Table of Contents
Advertisement
5
5
•
With a 7.1-channel surround system, audio signals that
have undergone matrix decoding processing through
surround back channel processing to which the Up Mix
function is added are output from the surround back
speakers.
CLR
SB CH
SB CH
CH SEL
BASS
BASS
TRE
TRE
SHIFT
SP-A/B
RECEIVER
SB CH
Press
repeatedly to cycle the surround back
channel options.
Each press cycles through the options as follows:
•
SB ON – Matrix decoding processing for generating
the surround back component from the surround
component is turned on.
•
SB AUTO – Matrix decoding processing for generating
the surround back component from the surround
component is switched automatically. Matrix
decoding processing is only performed when surround
back channel signals are detected in the input signals.
•
SB OFF – Matrix decoding processing for generating
the surround back component from the surround
component is turned off.
Setting the Up Mix function (VSX-1024 only)
In a 7.1-channel surround system with surround speakers
placed directly at the sides of the listening position, the
surround sound of 5.1-channel sources is heard from the side.
The Up Mix function mixes the sound of the surround
speakers with the surround back speakers so that the
surround sound is heard from diagonally to the rear as it
should be.
•
Using the Up Mix function is effective when the speakers in
the 7.1-channel surround system are set up as
recommended in the example on
page
•
Depending on the positions of the speakers and the sound
source, in some cases it may not be possible to achieve
good results. In this case, set the setting to OFF.
UP MIX OFF
SW
L
SL
SBL
1
Switch the receiver into standby.
2
While holding down
STANDBY/ON
hold the
UP MIX: OFF appears and the Up Mix function turns off.
If you want to turn this function on, perform steps 1 and
2 again.
•
When set to ON, the
panel lights.
Note
•
Set to ON regardless of this setting when playing DTS-HD
signals.
•
May automatically be set to OFF even when set to ON,
depending on the input signal and listening mode.
•
If the Network Standby is set to ON or Standby Through
is not set to OFF, you may not be able to set the Up Mix
function.
•
HDMI Control should also be set to OFF, not ON.
14.
UP MIX ON
C
SW
C
R
L
R
SR
SL
SR
SBR
SBL
SBR
PRESET
on the front panel, and
for about two seconds.
(Up Mix) indicator on the front
39
Listening to your system
Setting the Audio options
There are a number of additional sound settings you can
make using the AUDIO PARAMETER menu. The defaults, if
not stated, are listed in bold.
Important
•
Note that if a setting doesn't appear in the AUDIO
PARAMETER menu, it is unavailable due to the current
source, settings and status of the receiver.
AUTO
AUDIO P.
AUDIO P.
STANDBY/ON
SLEEP
SOURCE
TOP
TOP
MENU
MENU
RECEIVER
RECEIVER SIGNAL SEL
CTRL
CTRL
S.SEL
ECO
INPUT
BD
GAME
HDMI
DVD
SAT
MHL
HOME
MENU
iPod
CD
BT
1
Press RECEIVER, then press
AUDIO
2
/
Use
to select the setting you want to adjust.
Depending on the current status/mode of the receiver,
certain options may not be able to be selected. Check the
table below for notes on this.
3
/
Use
to set it as necessary.
See the table below for the options available for each
setting.
4
RETURN
Press
to confirm and exit the menu.
4
9
61
MUTE
SURR
ADV
TOOLS
MENU
ENTER
ENTER
RETURN
RETURN
BAND
PTY
Fav
P..
Advertisement
Table of Contents
Troubleshooting
