Advertisement
Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2020 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
20g
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for WARRIOR 57342
Summary of Contents for WARRIOR 57342
- Page 1 Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
-
Page 2: Table Of Contents
Cluttered or dark areas invite accidents. create sparks which may ignite the dust or fumes. c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. Page 2 For technical questions, please call 1-888-866-5797. Item 57342... -
Page 3: Safety
The correct power tool will do the job better and safer at the rate for which it was designed. Item 57342 For technical questions, please call 1-888-866-5797. Page 3... - Page 4 Page 4 For technical questions, please call 1-888-866-5797. Item 57342...
- Page 5 The saw blade could pick up one or more pieces and cause kickback. Item 57342 For technical questions, please call 1-888-866-5797. Page 5...
- Page 6 Association, and the National Electrical Code. 2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-prong plug.) Outlets for 2-prong plug Page 6 For technical questions, please call 1-888-866-5797. Item 57342...
- Page 7 Do not cover ventilation ducts. Keep flammable objects away. WARNING marking concerning n 0 xxxx/min. No Load Revolutions per Minute (RPM) Risk of Electric Shock. Properly connect power cord to appropriate outlet. Item 57342 For technical questions, please call 1-888-866-5797. Page 7...
-
Page 8: Specifications
4. Put the Table Saw in place and mount using the hardware mentioned above. Tighten all hardware securely before use. power Supply requirements 1. Connect to grounded 120VAC, 20A receptacle. Page 8 For technical questions, please call 1-888-866-5797. Item 57342... - Page 9 Gauge Guard insert Fence Dust port Fence Scale push Stick Storage Wrench Storage Miter Gauge Storage (on back) rip Fence Storage Blade power Height Lock Bevel Switch Handle Knob Scale Item 57342 For technical questions, please call 1-888-866-5797. Page 9...
- Page 10 1. Remove Table Insert, pull up by using hole. table insert b. Non-Through Cut 2. Raise Riving Knife Lock. riving Knife Lock 4. Lower Riving Knife Lock and replace Table Insert. Page 10 For technical questions, please call 1-888-866-5797. Item 57342...
- Page 11 2. Place Rip Fence on Work Table, then side to desired location using Scale if necessary. 3. Lower Rip Fence Lock. Fence Lock Dust Extraction Setup Attach dust collection system to Dust Port on back of Table Saw. Item 57342 For technical questions, please call 1-888-866-5797. Page 11...
- Page 12 30°-40° of the stick to keep hands out of the line of the blade. • The lower lip of the notch must be no longer than the workpiece is thick. Page 12 For technical questions, please call 1-888-866-5797. Item 57342...
-
Page 13: Operation
Replace Outer Flange and Blade Nut, then, tighten Blade Nut. DO NOT overtighten. 10. Move Blade Height Handle to 0°. Lower Saw blade completely, then replace Table Insert and Blade Guard. Item 57342 For technical questions, please call 1-888-866-5797. Page 13... - Page 14 Clamp smaller pieces to a piece of scrap wood that can reach beyond the Miter Gauge and hold the scrap against the Gauge while making the cut. Keep the clamp clear of the Saw Blade. Page 14 For technical questions, please call 1-888-866-5797. Item 57342...
- Page 15 1. Use a piece of wood that is 3/4″ thick, 3. Secure wood piece to the fence 3-1/2″ wide, and 18-1/2″ long. using 1-1/2″ wood screws. Item 57342 For technical questions, please call 1-888-866-5797. Page 15...
-
Page 16: Maintenance
With a brush, soft cloth, or vacuum, remove all sawdust from the Table Saw. allowing sawdust, scraps, or other debris to accumulate can cause a fire, resulting in severe personal injury or property damage. Page 16 For technical questions, please call 1-888-866-5797. Item 57342... - Page 17 See Extension Cords in Grounding section on page 6. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. Item 57342 For technical questions, please call 1-888-866-5797. Page 17...
- Page 18 LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Page 18 For technical questions, please call 1-888-866-5797. Item 57342...
- Page 19 Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 57342 For technical questions, please call 1-888-866-5797. Page 19...
-
Page 20: Parts List And Diagram
Pin 8x16 Spring Washer Riving Knife Plate Spring Nut M6 Pin 5x32 Hex Bolt M6x25, Spring Washer, Washer Cylindrical Pin 8x16 Rotating Base Riving Knife Handle Rotating Friction Plate Spring Page 20 For technical questions, please call 1-888-866-5797. Item 57342... - Page 21 Aluminium Profile Carbon Brush Backer Cover 2 Wool Washer Bolt M6×25 Washer Ø5x10x1 Knob Screw M5x12 Miter Gauge Screw Rod Miter Gauge Guide Bevel Gear Push Stick Screw M4x20, Washer Wrench Item 57342 For technical questions, please call 1-888-866-5797. Page 21...
- Page 22 Diagram Page 22 For technical questions, please call 1-888-866-5797. Item 57342...
-
Page 23: Warranty
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Item 57342 For technical questions, please call 1-888-866-5797. - Page 24 26541 agoura road • calabasas, ca 91302 • 1-888-866-5797...
Need help?
Do you have a question about the 57342 and is the answer not in the manual?
Questions and answers
how to adjust blade to 90 degrees on a warrior 10" table saw?
To adjust the blade to 90 degrees on a WARRIOR 10" table saw:
1. Turn off the power switch and unplug the saw from the outlet.
2. Loosen the Lock Knob.
3. Move the Blade Height Handle to the 0° position.
4. Tighten the Lock Lever.
This positions the blade at 90 degrees (perpendicular to the table).
This answer is automatically generated