Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Norma HS-IPA1
Summary of Contents for Norma HS-IPA1
- Page 1 E L E C T I C S HS-IPA1 SAFETY MANUAL USER MANUAL ORMA UDIO LECTRONICS TAKES NO RESPONSIBILITY FOR EVENTUAL ERRORS THAT MAY APPEAR IN THIS PRE PRODUCTION MANUAL N O R M A A U D I O E L E C T R O N I C S H S - I P A 1 S a f e t y &...
- Page 2 N O R M A A U D I O E L E C T R O N I C S H S - I P A 1 S a f e t y & U s e r M p a g A N U A L...
- Page 3 INDEX SAFETY MANUAL 1 PRELIMINARY INDICATIONS 2 PACKING & UNPCKINGA 3 TRANSPORT AND POSITIONING 4 CONNECTIONS 5 MAINTENANCE AND SUPPORT 6 USAGE 7 REMOTE CONTROL 8 GENERAL 9 RECYCLING, 10 LIMITATION of USE in USA-CANADA-MEXICO USER MANUAL 1 CONTROLS AND CONNECTION 2 USE 3 MAINTENANCE 4 SPECIFICATION...
-
Page 4: Packing & Unpacking
NORMA is not responsible for any damage resulting from wrong system grounding or inefficient directives and regulations. Also check that the mains voltage is the same as that which must be fed the equipment. -
Page 5: Maintenance And Support
7 - WARNING USB INPUT The optional USB input provided on the Norma REVO IPA-70B is designed to work with PCM signals of up to 192 KHz and DSD64 signal. The DSD signal MUST BE transmitted ONLY with “DSD OVER PCM” codification. Any other use of DSD signal might not be recognized from the USB receiver and could result in unexpected behaviours, which could seriously damage any equipment connected to the Norma REVO IPA-70B. - Page 6 11 - LIMITATION of USE in USA-CANADA-MEXICO The use of any NORMA AUDIO, OPAL ELECTRONICS product in USA, CANADA, MEXICO is authorized ONLY if the product has been imported and sold by NORMA’s official distributor, as indicated on NORMA AUDIO website (www.normaudio.com).
- Page 7 User Manual Congratulations! The product you have purchased and you are going to use is the result of a long process of research and development, to bring you the best that current technology allows us to express in electronic intended for audio playback, both in terms of construction quality that listening quality.
-
Page 8: Controls And Connection
1 - CONTROLS AND CONNECTION Refer to the attached drawing in the last pages of the manual 1.1 – Front Panel 1 - Multi-function display The display show the controls and functional states. 2 - Indicator POWER STAND-BY In the state of STAND-BY indicator is illuminated. In the state of POWER ON indicator is off. - Page 9 - The electrical safety is due to its connection to safety ground. Before connecting and use the device, make sure that the grounding system is efficient. . NORMA is not responsible for any damage resulting from wrong system grounding or inefficient directives and regulations or a disconnection in any way made, ground security equipment.
- Page 10 30 seconds. 2.3 PROTECTION CIRCUIT Inside the amplifier HS-IPA1 are present some sophisticated protection circuits that control the temperature of the heatsinks, the presence of any offset current exceeding the limit value and the abnormal supply of output current (short circuit).
-
Page 11: Connecting The Speakers
2.7 CONNECTING THE SPEAKERS The speakers should be connected by wires to the SPEAKERS OUTPUT of adequate quality and diameter [at least 4 mm ｲ]. In addition: - The connection cables must have the same length for both channels even if the distance between the speakers and the amplifier should be different;... - Page 12 2.8.2 – Analog Settings This sections lets you set the volume levels for every set of inputs (digital if present, analog 1-4). If you leave the setting in OFF, when selecting an input it will keep the current volume. If you define a specific value, when selecting the input, the unit will automatically turn the volume control in that position.
- Page 13 2.11 – Remote Control (16 buttons) 1 - ON/OFF Turns the device on or puts it in stand-by. 2 - MUTE Mutes the outputs. The device will not accept other commands until mutes is pressed again. 3 - VOL +/- Adjusts the volume.
- Page 14 2.12 – Headphones (Optional) The optional headphone output of the HS-IPA1 is a very high quality one, able to gracefully drive even the most demanding headphones. It is possible to set it in 4 different positions via internal jumpers, to best fit it for each kind of headphone.
- Page 15 POSITION 2 – 32-60 Ohm (default) --||---- --||---- POSITION 3 – 200-600 Ohm ----||-- ----||-- POSITION 3 – Direct Connection - ATTENTION In this position the headphone is connected directly to the power output, the same that drives the speakers. This position is to be used only with very particular headphones taht need high power to drive.
-
Page 16: Maintenance
The manufacturer is available to clients for any problem. NORMA is not responsible for any errors, omissions or incompleteness of this manual, as it is not responsible for accidents or damages of any kind that may result from non-compliance, even partial, of the information provided in this manual. -
Page 17: Specifications
Dimensions (HxWxD) 126 x 215 x 350 mm Note Integrated amplifier with full remote control by NORMA IR In order to improve its products, NORMA reserves the right to vary all the technical specifications and appearance without notice. N O R M A A U D I O E L E C T R O N I C S . - Page 18 5 TESTING HS-IPA1 Model __________________________________________________________ Version __________________________________________________________ Accessories __________________________________________________________ Serial Number __________________________________________________________ First Tester __________________________________________________________ Second Tester __________________________________________________________ Third Tester __________________________________________________________ Date N O R M A A U D I O E L E C T R O N I C S .
- Page 19 N O R M A A U D I O E L E C T R O N I C S . 1 9 H S - I P A 1 S a f e t y & U s e r M p a g A N U A L...