Advertisement
6.6.
iMPORtANt WARNiNG - Air contaminants taken into the compressor will affect optimum performance. example: Body filler dust or
paint overspray will clog the pump intake filter and may cause internal damage to pump/motor components. Please note that any parts
damaged by any type of contamination will not be covered by warranty.
7. tROUBLESHOOtiNG
FAULt
1A) Pressure drop in the tank
1B) Pressure drop in the tank
1c) Pressure drop in the tank
2) Pressure switch valve leaks when
compressor is idle
3) Air leaks from tank body or tank welds
4A) motor stops and will not restart
4B) motor stops and will not restart
5) compressor stops and does not restart
6A) compressor does not stop at max. pressure
6B) compressor does not stop at max. pressure
7) compressor noisy with metallic knock
8) excessive moisture in discharged air
Parts support is available for this product. to obtain a parts listing and/or diagram, please log on to www.sealey.co.uk,
Environmental Protection.
recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a manner which
is compatible with the environment.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMPORtANt: no liability is accepted for incorrect use of this product.
WARRANtY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
iNFORMAtiON: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
© Jack sealey limited
CAUSE
Air leaks at connections
Air leaks from safety valve
Air leaks from cylinder head gasket
non-return valve seal defective
Internal corrosion caused by infrequent tank
draining or non permitted modifications to tank
thermal cut out has operated
supply fuse has tripped
motor failure
Pressure switch fault
filter clogged
Head gasket or valve fault
Bearing or piston damage
High humidity environment
email sales@sealey.co.uk or phone 01284 757500.
Sole UK distributor, Sealey Group,
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk,
IP32 7Ar
Original Language Version
run compressor to max. pressure, switch off
Brush soap solution over connections and look for
bubbles. tighten connections showing leaks
If problem persists contact Authorised service Agent
operate the safety valve manually by pulling on the
ring. If valve continues to leak when in the closed
position it should be replaced
check tightness of head bolts. If leak continues
contact authorised service agent
empty the air tank. referring to fig.6, remove the
non-return valve cap (3), spring (2) and seal (1)
clean the seal and its seat, or if necessary replace
tank could rupture or explode. Beyond repair
diSCONtiNUE USE iMMEdiAtELY
Allow unit to cool for 30 minutes before restarting
reset fuse and restart unit. If repeated tripping
occurs replace the check valve or contact
authorised service agent
contact Authorised service Agent
contact Authorised service Agent
replace filter element.
contact Authorised service Agent
contact Authorised service Agent
drain tank after each use
WEEE Regulations.
dispose of this product at the end of its working life in compliance
with the eu directive on Waste electrical and electronic equipment.
When the product is no longer required, it must be disposed of in an
environmentally protective way. contact your local solid waste
authority for recycling information.
01284 757500
01284 703534
sAc5020e110V
REMEdY
the seal
fig.6
www.sealey.co.uk
Web
sales@sealey.co.uk
email
Issue no: 4 (I) - 15/07/13
Advertisement
