Table of Contents
Summary of Contents for Wel-Bilt 193024
- Page 1 4-BIKE HITCH RACK OWNER’S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item # 193024...
-
Page 2: Intended Use
Thank you very much for choosing a Wel-Bilt™ product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. -
Page 3: Work Area
WORK AREA When assembling, installing, or removing the bike hitch rack • Keep work area clean, free of clutter and well lit. Cluttered and dark work areas can cause accidents. • Keep children and bystanders away while assembling, installing or removing the bike hitch rack. - Page 4 Qty 1: Pin (Part #16) Qty 1: “R” Pin (Part #17) See figure#1 below. Attach turn elbow plate (Part #22) onto hitch base (Part #23) using M16X75 bolt, M16 nut and washer (see specific hole location below). Next, insert Pin (Part #16) to the second hole (see below) using “R”...
- Page 5 Step 3: Attach Top Support Plate Hardware Needed: Qty 1: Elbow Support Part #24) Qty 1: Bolt M10 (Part #1) Qty 1: Ф10 spring washer (Part #2) Qty 3: Ф10 washer (Part #3) Qty 1: Bolt M10X60 (Part #4) Qty 4: Plastic (Part #5) Qty 1: Nut M10 (Part #8) Qty 1: “W”...
- Page 6 Step 4 Connect assembled Join tube Hardware Needed: Qty 1:Bike holder Tube (Part #20) Qty 1:Bolt M10 (Part #1) Qty 1: Ф10 spring washer (Part #2) Qty 1: Ф10 washer (Part #3) Qty 4: Plastic (Part #5) Qty 1: Ф12 pin (Part #6) Qty 1: Bolt M10 (Part #7) Qty 1: Bike Holder Plate (Part #18) Note the bike holder plate (Part #18)and plastic (Part #5) are pre-assembled onto the bike holder...
- Page 7 Step 5. Assembly Completed IMPORTANT! Check that all connections are tight. Attach bike hitch rack to vehicle receiver hitch, securing it with a hitch pin (not included). Page of 11...
-
Page 8: Operation
OPERATION WARNING: RISK OF FIRE/FIRE HAZARD • Never allow loads or items on the bike hitch rack to block or impede exhaust from vehicle. • This can cause a fire or damage to personal property or vehicle. Step 1: Two person installation is recommended to lift the bike hitch rack into place. Step 2: Lift the bike hitch rack and insert receiver mounting bar into the hitch receiver on the vehicle. -
Page 9: Maintenance
MAINTENANCE • Maintain your bike hitch rack. It is recommended that the general condition of the rack be examined before it is used. Keep the rack in good repair by adopting a program of conscientious repair and maintenance in accordance with the recommended procedures found in this manual. •... -
Page 10: Diagram & Parts List
DIAGRAM & PARTS LIST Part# Description Qty. Part# Description Qty. Bolt M10 Bolt M16X75 Ф10 Spring Washer Ф16 Washer Ф10 Washer Nut M16 Bolt M10X60 Plastic “R” Pin Ф12 Pin Bike Holder Plate Bolt M10 “W” Plate Nut M10 Bike Holder Tube Bolt M12X75 Center Support Ф12 Washer... -
Page 11: Warranty
WARRANTY One-Year Limited Warranty Distributed by Northern Tool + Equipment Co., 2800 Southcross Drive West P.O. Box 1499 Burnsville, MN 55337-0499 Made in China Page of 11...