Subscribe to Our Youtube Channel
Related Manuals for MICRO-AIR EasyTouch 357
Summary of Contents for MICRO-AIR EasyTouch 357
- Page 1 EasyTouch Operating Manual Revision 1.7 ©2021 Micro-Air Corp October 13, 2021; revision 1.7...
-
Page 2: Table Of Contents
Appendix B: WIFI Troubleshooting ......................12 No WIFI Icon ............................12 Red WIFI Icon ............................12 Appendix C: Connecting remotely ......................13 First connection steps ..........................13 Adding a control ............................13 ©2021 Micro-Air Corp October 13, 2021; revision 1.7... -
Page 3: Special Note On Temperature Sensors Used In The System
The thermostat should be mounted in a location that gives it a good chance of reading accurate room temperature. ©2021 Micro-Air Corp October 13, 2021; revision 1.7... -
Page 4: Installing The Thermostat
The EasyTouch 357 model thermostat was designed to replace certain Dometic™ multi-zone capable thermostats. Original thermostats replaced by this model are a five-button configuration with a display alongside the buttons. If your thermostat is not of this style, please contact Micro-Air https://www.micro-air.com/SupportRequest to verify the thermostat you received is correct for your application. -
Page 5: Mounting The Thermostat
Press the display against the wall and gently slide the display down to lock it in place. Step 3: Screw in second screw making sure the two buttons remain level. ©2021 Micro-Air Corp October 13, 2021; revision 1.7... -
Page 6: Initial Setup Instructions
All control boards in the system would need to be changed and EasyTouch would need to be re-flashed to new firmware. Re-flashing can be done by sending the thermostat to Micro-Air for an upgrade to our 350-thermostat firmware. ©2021 Micro-Air Corp... -
Page 7: Operating The Thermostat
See table 2 for a list of all possible modes. Table 1 Fan only Zone off Heat pump Zone on Cool Only Furnace ©2021 Micro-Air Corp October 13, 2021; revision 1.7... -
Page 8: Additional Indications On Main Screen
If the system is a staged system with more than one compressor per zone, a staging message will appear on the screen. Press the stage message to turn on or off the second stage for this zone. ©2021 Micro-Air Corp October 13, 2021; revision 1.7... -
Page 9: Schedule Screen
The Home/Schedule icon on the main screen will show if you are in Home mode or Schedule mode 5. Press the round arrow to return to the regular settings screen. ©2021 Micro-Air Corp October 13, 2021; revision 1.7... -
Page 10: Settings Screen
10. Reset all will reset the thermostat to factory settings including all set points, schedule events, and other settings. 11. The QR code will bring you to the Micro-Air EasyTouch page when selected using a QR compatible phone app. Below the QR code is the serial number for the thermostat and the firmware revision for the thermostat. -
Page 11: Gas Heat Override
This behavior helps avoids nuisance notifications to your smart device. Table 3 Temperature °F Action Send first notification Send another notification Send another notification 81…79 Temperature drops, no notification Max temp resets ©2021 Micro-Air Corp October 13, 2021; revision 1.7... -
Page 12: Appendix A: Installation Troubleshooting
The router must have an internet connection • Server may be down, check back at a later time • Be sure there is no firewall in the router blocking the incoming messages (port 443, HTTPS). ©2021 Micro-Air Corp October 13, 2021; revision 1.7... -
Page 13: Appendix C: Connecting Remotely
2. Connect to the thermostat and press the settings gear, then tap Check for Updates. 3. Follow the prompts to update the thermostat or ensure that you already have the latest software. ©2021 Micro-Air Corp October 13, 2021; revision 1.7...
Need help?
Do you have a question about the EasyTouch 357 and is the answer not in the manual?
Questions and answers