Advertisement

EasyTouch
352 and 352C
Operating Manual
Revision 1.4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EasyTouch 352 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for MICRO-AIR EasyTouch 352

  • Page 1 EasyTouch 352 and 352C Operating Manual Revision 1.4...
  • Page 2: Table Of Contents

    Check for updates ........................... 14 Notifications ............................14 Installation Troubleshooting ........................15 Testing an output ............................ 15 WIFI Troubleshooting ..........................15 Appendix: First connection steps ........................ 16 Adding a control ............................16 ©2021 Micro-Air Corp May 20, 2021, revision 1.4...
  • Page 3 Connecting to a new WIFI network ......................16 Updating the thermostat ........................16 ©2021 Micro-Air Corp May 20, 2021, revision 1.4...
  • Page 4: Installing The Thermostat

    The EasyTouch 352 model thermostats were designed to directly replace Coleman™, Airxcel™ and RVP™ single zone DC thermostats. The thermostats can be used in other applications with certain electrical limitations as explained later in this document. Installing the thermostat There are three steps to installing the thermostat. First remove your old thermostat. Next disconnect and reconnect the wiring.
  • Page 5: Wiring The Thermostat

    RV DC power circuit powering the thermostat. We also recommend taking a picture of the original Figure 2 thermostat wiring order so you can verify the connection order on the new thermostat. ©2021 Micro-Air Corp May 20, 2021, revision 1.4...
  • Page 6: Direct Wired Models

    Sensor Green/White stripe Sensor Figure 3 Note: The sensor wires (green with white stripe) may be connected either way as long as one wire is connected to each of the SEN terminals. ©2021 Micro-Air Corp May 20, 2021, revision 1.4...
  • Page 7: Using This Thermostat On Other Applications

    It is possible to use this thermostat for custom installations. The outputs are all +12-volt active and open collector (high impedance) inactive outputs. Maximum drive current is 200mA per output. This thermostat cannot be used for 24 VAC applications. Contact Micro-Air if you are not certain this device will work in your intended application.
  • Page 8: Mounting The Thermostat

    Press the display against the wall and gently slide the display down to lock it in place. Step 3: Screw in second screw making sure the two buttons remain level. ©2021 Micro-Air Corp May 20, 2021, revision 1.4...
  • Page 9: Initial Setup Instructions

    If a second user is going to use the thermostat remotely, they can use the same account and password as the first user. Each thermostat can only be assigned to a single account. ©2021 Micro-Air Corp May 20, 2021, revision 1.4...
  • Page 10: Operating The Thermostat

    A white icon indicates no cycle is in process The hourglass symbol indicates that a delay is in process and operation will resume once the delay is complete. It is an indication that the display is handling the requested operation. ©2021 Micro-Air Corp May 20, 2021, revision 1.4...
  • Page 11: Away Screen (Heat And Cool Set Points)

    The upper value changes the cooling set point and the lower value changes the heating set point. 2. Use the up and down arrows to change the selected temperature value. ©2021 Micro-Air Corp May 20, 2021, revision 1.4...
  • Page 12: Schedule Screen

    The button will only select between home and away if the schedule is disabled. Away mode is not configurable on a schedule. 5. Press the round arrow to return to the regular settings screen. ©2021 Micro-Air Corp May 20, 2021, revision 1.4...
  • Page 13: Settings Screen

    9. The back icon will return the display to the operating screen. 10. The QR code will bring you to the Micro-Air EasyTouch page when selected using a QR compatible phone app. Below the QR code is the serial number for the thermostat and the firmware revision for the thermostat.
  • Page 14: Gas Heat Override

    WIFI must be connected and active on the thermostat for the notification to function. Notifications will be sent for each degree of temperature change. ©2021 Micro-Air Corp May 20, 2021, revision 1.4...
  • Page 15: Installation Troubleshooting

    If you are in a metal enclosure, try moving the router or thermostat a few inches (even if temporary) and trying again. • If using MAC filtering, add the thermostat to the allowed devices list. ©2021 Micro-Air Corp May 20, 2021, revision 1.4...
  • Page 16: Appendix: First Connection Steps

    2. Connect to the thermostat and press the settings gear, then tap Check for Updates. 3. Follow the prompts to update the thermostat or ensure that you already have the latest software. ©2021 Micro-Air Corp May 20, 2021, revision 1.4...

Table of Contents