Freestyle Shark Skin Diver Instructions

SKIN DIVER
INSTRUCTIONS
BUTTON FUNCTIONS
• [LIGHT] : Active backlight
• [MODE] : Change function mode
• [LAP/RST] : Enter setting state
• [ST/STOP] : Start/Stop timing
function
• [COMPASS] : Compass mode
LCD SEGMENT LAYOUT
LCD Segment Layout with all
segments turned on.
MODES
• There are seven modes: Time
of Day, World Time, Compass,
Alarm, Chrono, Recall, Timer
• TIME OF DAY (TOD) is default
mode
DEFAULT TIME OF
DAY SETTINGS
• Time: 12:00 AM; Thursday,
January 1, 2015; 12-hour
format; MM-DD format
• Hourly Chime: Off
• Beep: Off
• Leap Year: Only applicable in
years with February 29th
• Date Range: 2015 - 2099
• Time with Hour, Minute, Second,
Day of week, Month, Day/Time
displayed in 12/24 hour format
• Automatic Leap year adjustment
SET THE TIME OF DAY
• Press [LAP/RST] and hold 3
seconds to set Time/Date
• Sequence is: City Hour > Minute
> Second > Hour Format > Day >
Month > Year >
DST > Beep > Chime
• Press [MODE] to change
the setting
• Press [MODE] and hold 2
seconds (or hold for 60 seconds
to reset to default)
• Press [ST/STOP] or [LAP/RST]
and hold 3 seconds, will increase
or decrease the setting value
• Chime ON will set chime hourly
• Chime OFF will turn off
hourly chime
• Beep ON will turn on a beep
sound when active buttons are
pressed
• Beef OFF will turn off beeps
• When in any mode setting, all
alarms are temporarily disabled
and re-enabled upon exit
• Available days are aligned with
each month (ex. February will
have available days of 1 to 28
or 1 to 29 (leap year).
DEFAULT WORLD
TIME SETTINGS
• 32 cities/zones
• Time displayed in 12- or
24-hour format (same as local
time setting)
SET WORLD TIME
• Press [ST/STOP] to enter the
next city time
• Press [LAP/RST] to enter the
previous city time
• Press and hold [ST/STOP] for 2
seconds to set DST ON or OFF
• All Display Format is the same as
normal time
DEFAULT WORLD
COMPASS SETTINGS
NOTE: Compass must be calibrated
before using
• Degree: 0° - 360°
• 16 cardinal directions (N, NNW,
NW, WNW, W,WSW, SW, SSW, S,
SSE, SE, ESE, E, ENE, NE, NNE)
• Digital direction indication in
degree with 1 degree interval
(as measured from North)
• Compass calibrate and
declination
CALIBRATE THE COMPASS
• Calibrate compass before using
• Place watch on flat surface away
from large metallic objects or
electromagnetic (EM) signals
• Outer bar graph will direct user
to rotate watch clockwise for 2
complete revolutions within
60 seconds
• Press [ST/STP] for 60 seconds
to confirm and exit
• Press [LAP/RST] and hold for
3 seconds to enter calibration
mode
• Press [ST/STP] once to start
calibration process
• Press [ST/STP] again to
complete the calibration and go
back to COMPASS mode
• If no button is pressed for
60 seconds, it will return to
COMPASS mode
SET THE COMPASS
• If DIST displays, move away from
large metallic objects or strong
EM signals
• Watch will measure magnetic
North.
• To set to true north, enter a
declination value and adjust
for angle
• After 3 minutes, watch
will return to TOD mode
automatically
SET DECLINATION
• Press [LAP/RST] for 3 seconds
to enter CALIBRATION mode.
The screen will show [CAL]
• Press [MODE] for 2 seconds to
enter Declination
• The screen will show [DEC]
• You can enter between East
(E) and West (W), 0~90 degree
• Press [MODE] for 2 seconds to
confirm the value and return to
COMPASS mode
DEFAULT ALARM SETTINGS
• All alarms: 12:00 AM; OFF
• Two daily alarm with the
sound alert
• Snooze function with 60
second interval
• Set alarm to activate on either
digital home time or digital
world time
SET THE ALARM
• Press [ST/STOP] to turn on/off
the alarm switch; once ON, icon
will display
• Press [LAP/RST] to switch
between AL1 and AL2
• Press and hold [LAP/RST] for 3
seconds to enter alarm setting
• Press [LAP/RST] to set Alarm
Minute > Alarm Hour > HT/WT
• Press [ST/STOP] to increase
value or press [LAP/RST] to
decrease the value
• Press [ST/STOP] or [LAP/RST]
and hold 3 seconds to increase
or decrease the setting at 8
times per second
• Alarm time will display in same
time format as primary time; PM
will only display in 12H format
• When it is alarm time setting
state, if the alarm data is
changed, the alarm switch is
turned on automatically.
• If no button is pressed for 60
seconds, it will return to ALARM
mode
• Alarm will sound for 20 seconds,
alarm icon will blink, and snooze
option becomes available
• Alarm time will display when the
alarm sounds when in Time of
Day, World Time, Alarm, and
Recall modes
ENGLISH