Advertisement
GB
Dear Customer,
Congratulations on your choice of purchase: this IMER saw, the
result of years of experience, is a fully reliable machine and is
equipped with the latest technical innovations.
- WORKING IN SAFETY
To work in complete safety, read the following
instructions carefully.
- This OPERATION AND MAINTENANCE manual must be kept on
site by the person in charge, e.g. the SITE FOREMAN, and must
always be available for consultation.
This manual is to be considered an integral part of the machine, and it
must be preserved for future reference (EN292/2) throughout the
machine's normal working life. If the manual is damaged or lost, a
replacement may be requested from the saw manufacturer.
- The manual contains important information regarding site
preparation, installation, machine use, maintenance procedures
and requests for spare parts. Nevertheless, the installer and the
operator must both have adequate experience and knowledge
of the machine prior to use.
- To guarantee complete safety of the operator, safe operation
and long life of equipment, follow the instructions in this manual
carefully, and observe all safety standards currently in force for
the prevention of accidents at work. Use personal protection
(safety footwear, suitable clothing, gloves, goggles, etc.).
- Safety glasses or a protective visor must be worn at all
times.
- Ear protection must be worn at all times.
- MAKE SURE THAT WARNING SIGNS ARE ALWAYS
LEGIBLE.
- It is strictly forbidden to carry out any form of
modification to the steel structure or working parts of the
machine.
- IMER INTERNATIONAL declines all responsibility for non-
compliance with laws and standards governing the use of this
equipment, in particular; improper use, defective power supply,
lack of maintenance, unauthorised modifications, and partial or
total failure to observe the instructions contained in this manual.
IMER INTERNATIONAL is entitled to modify the characteristics of
the sawing machine and/or the contents of this manual without
necessarily updating previous machines and/or manuals.
1. TECHNICAL DATA
Table 1 shows the saw's technical data, referring to figure 1.
TABLE 1
TECHNICAL DATA
Blade rpm
Blade diameter
Blade mounting hole
Motor rating
Voltage
Current
Frequency
Motor rpm
Cutting table dimension
Overall dimensions
(widthxlengthxheight)
Overall dimensions for
transport
(widthxlengthxheight)
Weight
Weight for transport
Blade rotation direction(seen
from blade clamping flange)
2. DESIGN STANDARDS
MASONRY 350 F saws are designed and manufactured according to
the following standards: EN 292-1-2; EN 12418; EN 60204-1.
3. NOISE EMISSION LEVEL
Table 2 indicates the noise level produced by the sawing machine,
measured at the operator's ear (L
environmental noise emission level (power L
accordance with EN ISO 3744; UNI EN 12418.
IMER INTERNATIONAL S.p.A.
MASONRY 350 F
1188793
1188797
rpm
1.980
1.910
mm
350
mm
25,4
Kw
2,2
1,7
V
230
110
A
12
21
Hz
50
rpm
2.800
2.700
cm
50 x 43
cm
86 x 118 x 136
cm
83 x 125 x 98
Kg
112
Kg
132
CLOCKWISE
at 1 m - 98/37CE) and the
pA
) measured in
WA
SA W ING M A CHINE
TYPE O F M O TO R
M asonry 350F EL
ELECTR IC
4. CUTTING SPECIFICATIONS
This saw model has been specially designed for cutting stone,
ceramics, marble, granite, concrete and similar materials. Only
water-cooled diamond blades with continuous or segmented
edges (see paragraph 13) must be used. Under no
circumstances must dry cutting blades be used or materials
other than those specified above. IMER INTERNATIONAL
declines all responsibility for damage caused by improper use
of the above machine.
5. CUTTING CAPACITY
- max. cutting capacity with vertical blade = 120mm in one
single pass.
- max. height of workpiece: 230 mm (in two passes).
- min. width of workpiece: 50mm.
- max. cutting length: 470 mm (with blade lowered), 550 mm
(with blade fully raised).
-Blade at 45°: with support at 45° on the work surface.
6. WARNING
- Do not load the saw with workpieces that exceed the specified
weight (max. 40 kg)
- Ensure stability of machine: it must be installed on a solid
base with a maximum slope of 5° (fig. 2).
- Ensure the workpiece is stable before, during and after cutting:
in any case, workpieces must not overhang the worktable.
- Respect the environment; use suitable receptacles for
collection of cooling water contaminated with cutting dust.
7. SAFETY PRECAUTIONS
- IMER saws are designed for work on construction sites and
under conditions of natural light, hence the workplace must be
adequately lit.
- The machine must never be used in environments
subject to risks of explosion and/or underground sites
- IMER saws may only be used when fitted with all required
safety devices, which must be in perfect condition.
- Never use makeshift and/or faulty power cables.
- Make electrical connections on the construction site where
they will not be subject to damage. Never stand the saw on
power supply cables.
- Lay power cables in such a way as to prevent water
penetration. Only use connectors fitted with water-spray
protection (IP57, EEC).
- Repairs to electrical installations must only be carried out by
qualified technicians. Always ensure that the machine is
disconnected from the power supply and is completely immo-
bile during repairs and maintenance operations.
- Connect the machine to a suitable
equipotential earthing plant on the construction
site with wire braid of minimum 16 mm² section.
The connection point is identified by a screw
welded to the frame (Ref. 15, fig.1), and on the
rating plate by the earthing symbol.
- Stop the saw only by means of the main switch
(Ref. 7, fig. 1).
- The symbol shown on the label (see left)
indicates
PROTECTION DEVICES ARE INSTALLED AND IN
PERFECT CONDITION BEFORE SWITCHING ON
THE MACHINE" (fig.3).
Fig. 3
8. ELECTRICAL SAFETY
IMER saws comply with EN 60204-1; and are fitted with:
- Protection device against automatic re-start after power failure.
- Short-circuit cutout device
- Motor overload cutout switch
9
GB
TA BLE 2
L
(dB)
L
(dB)
p
A
W A
86
98
the
warning
"ENSURE ALL
Advertisement
