Sharp PN-Q901 Setup Manual page 35

Using a PC
Adjusting the PC Image
You can adjust the position of the image input a PC
by selecting
"Initial Setup" > "Input Settings" > "Fine Sync."
Fine Sync.
Ordinarily you can easily adjust the picture as
necessary to change image position using "Auto
Sync.". In some cases, however, manual adjustment
is needed to optimize the image.
Input Signal: Select the input signal.
1024×768
1360×768
Auto Sync.: For automatically adjusting the PC
image.
Yes : Auto Sync. starts and "Now adjusting the
image." is displayed.
No : This function does not work.
H-Pos. : Centers the image by moving it to the left
or right.
V-Pos. : Centers the image by moving it up or
down.
Clock : Adjust when the image flickers with
vertical stripes.
Phase : Adjust when characters have low
contrast or when the image flickers.
NOTE
• Auto Sync. may fail if the computer image has low
resolution, has unclear (black) edges, or is moved while
executing "Auto Sync.".
• Be sure to connect the PC to the Monitor and switch it
on before starting "Auto Sync.".
• It is not necessary to adjust the "Clock" or "Phase"
when a digital signal is being input, so it cannot be
selected.
• The default cursor position may not be in the center,
because the screen position variable ranges may be
asymmetrical.
• The screen position variable ranges depend on the
View Mode or the signal type. The ranges can be seen
on the position-setting screen.
Setting Audio Input
Audio Select
This function sets the terminal to output the
computer audio.
The adjustment items vary depending on the input
source.
Select the input source corresponding to the terminal
connected to the PC and then adjust the desired
item.
To perform the operation, refer to "Initial Setup" >
"Input Settings" > "Audio Select".
HDMI 2
HDMI2(Digital) : Select this when the Monitor
and PC are connected using
an HDMI-certified cable and
audio is input via the same
cable.
HDMI+Analog : Select this when the Monitor
and PC are connected using
an HDMI-certified cable and
the audio is input via a Ø 3.5
mm stereo minijack.
NOTE
• When "Audio Select" is set to "HDMI+Analog", sound
will not be produced if you use only an HDMI-certified
cable to connect HDMI-compatible equipment. To
produce sound, you should make an analog audio
connection.
• If you want to connect HDMI-compatible equipment
using only an HDMI-certified cable, set "Audio Select"
to "HDMI2(Digital)".
Control of the Monitor
• The Monitor can be controlled from a PC, control
panels and other devices using the RS-232C or IP.
• Use a cross-type RS-232C cable, ETHERNET
cable (commercially available) for the connections.
NOTE
• This operation system should be used by a person
who is accustomed to using computers.
IP Control
Set this function when operating the Monitor from
equipment connected by LAN. To perform the
operation, refer to "Network Settings".
IP Control
When "IP Control" is selected, "Change" will be
highlighted. Press ENTER.
Detailed Settings
Make the detailed settings (Login ID, password,
etc.).
Follow the on-screen instructions to configure
the settings.
Device Name
• Set the name of the Monitor displayed on other
network devices.
Use the software keyboard to set the name.
ETHERNET cable
EN 10
Communication Conditions For RS-232C
Set the RS-232C communication settings on the PC
to match the Monitor's communication conditions.
The Monitor's communication settings are as follows:
Baud rate: 9,600 bps
Data length:
8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
Communication Conditions for the IP
Connect to the Monitor with the following settings
made for IP on the PC
IP protocol: TCP/IP
Host IP address: Set the IP address on the
Monitor menu
Service: None (Do not select Telnet or
SSH)
TCP port#: Set a port number on the
Monitor menu (Control port)
When you set your ID and password on the Monitor
menu, you need to enter them as soon as you
connect to the Monitor.
NOTE
• When you use this function, make settings for "IP
Control".
• The connection will be cut off when there has been no
communication for 3 minutes.
Cross-type RS-232C cable
LAN
Hub