Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for United Technologies Interlogix IFS NS3550-8T-2S
Summary of Contents for United Technologies Interlogix IFS NS3550-8T-2S
-
Page 1: Ifs Ns3550-8T-2S Quick Installation Guide
IFS NS3550-8T-2S Quick Installation Guide P/N 1072772 • REV A • ISS 24JUN14... - Page 2 Copyright © 2014 United Technologies Corporation, Inc. Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved. The IFS NS3550-8T-2S and logo are trademarks of United Trademarks and patents Technologies. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
-
Page 3: Table Of Contents
TABLE OF CONTENTS IFS NS3550-8T-2S Quick Installation Guide ................1 TABLE OF CONTENTS......................3 INTRODUCTION........................4 Package Contents ..............................4 Requirements ..............................4 Wiring the Power Input ..............................5 Starting Web Management ...................... 6 TROUBLESHOOTING......................10 Resetting the IP address and Admin Password......................10 Contacting Technical Support.................... -
Page 4: Introduction
INTRODUCTION The IFS NS3550-8T-2S is an 8 port Gigabit Industrial Switch with 2 SFP fiber ports and robust layer 2 features. Package Contents Open the box of the Industrial Managed Switch and carefully unpack it. The box should contain the following items: Check the contents of your package for following parts: ... -
Page 5: Wiring The Power Input
Wiring the Power Input The 6-contact terminal block connector on the rear panel of NS3550-8T-2S is used for two DC redundant powers inputs. Please follow the steps below to insert the power wire. Insert positive / negative DC power wires into contacts 1 and 2 for DC POWER 1, or 5 and 6 for DC POWER 2. Tighten the wire-clamp screws to prevent the wires from loosening. -
Page 6: Starting Web Management
Starting Web Management This section introduces the configuration and functions of the Web-Based management. About Web-based Management The Industrial Managed Switch offers management features that allow users to manage the Industrial Managed Switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer. The Web-Based Management supports Internet Explorer 7.0 or higher. - Page 7 Figure 1: Web Management Diagram Logging into the switch Use Internet Explorer 7.0 or above Web browser. Enter the factory-default IP address to access the Web interface. The factory-default IP Address is as follows: http://192.168.0.100 When the following login screen appears, please enter the default username "admin" with password “admin” (or the username/password you have changed via console) to login to the main screen of Industrial Managed Switch.
- Page 8 Figure 3: Default Main Page It is recommended to use Internet Explore 7.0 or above to access Industrial Managed Switch. If the IP address of the switch is changed, the change will take effect immediately after you click on the Save button, Therefore, you need to use the new IP address to access the Web interface.
- Page 9 Main Menu Using the onboard web agent, you can define system parameters, manage and control the Industrial Managed Switch, and all its ports, or monitor network conditions. Via the Web-Management, the administrator can setup the Industrial Managed Switch by select the functions those listed in the Main Function.
-
Page 10: Troubleshooting
TROUBLESHOOTING Resetting the IP address and Admin Password To reset the IP address to the default IP Address “192.168.0.100” or reset the password to default value, press the hardware reset button at the front panel about 10 seconds. After the device is rebooted, you can login the management WEB interface within the same subnet of 192.168.0.xx. -
Page 11: Contacting Technical Support
Contacting Technical Support Contact technical support if you encounter any difficulties during this installation. Please make sure you have the requested diagnostic or log files ready before you contact us by phone or go to www.interlogix.com/customer-support. IFS / Interlogix online FAQ : http://www.interlogix.com/transmission US Support By Phone... -
Page 12: Emea Support
MobileView Support MobileViewCS@fs.utc.com MobileView Tech Support MobileViewTS@fs.utc.com EMEA Support By Phone +32 (0)2 725 1120 By Mail EMEA Headquarters UTC Fire & Security EMEA BVBA (Europe, Middle East & Africa) Kouterveldstraat 2 1831 Diegem-Brussels, Belgium By Email Email emea@fs.com...