Advertisement
Quick Links
Advertisement
Related Manuals for Garlando TOORX SRX SPEED MAG
Summary of Contents for Garlando TOORX SRX SPEED MAG
- Page 1 MANUALE D’ISTRUZIONI...
-
Page 2: Exploded Diagram
EXPLODED DIAGRAM... -
Page 3: Hardware Package
HARDWARE PACKAGE... - Page 4 PARTS LIST Description Qty. Description Qty. Computer Rubber Paste 2×29×19 Computer Holder Fixed Plate of Horizontal saddle tube Bolt M5*20 Saddle Tube Grommet Φ12.5 36L/R Pedal Knob M16 Bolt M8*35*S6 Washer d8*φ16*1.5 Main Frame Bolt Φ7.8*30*M6*15*S5 Cap Nut M8*H16*S13 Foam Grip φ27*3*120 Bearing 608ZZ End cap φ28*17 Roller Φ71*Φ19*24...
- Page 5 Description Qty. Description Qty. Bolt Nut M10 Limiter bushing 89L/R Crank Bolt M5*5*S2.5 Cover Knob Washer d20 Sensor Bearing 6004-RZ Bushing Φ25*Φ21*4 Bolt M6*10*S10 Nylon nut M10*H9.5*S17 Wave washer d20*Φ26*0.3 Bolt M6*52*Φ10*2.5 Bolt ST4.2*16*Φ8 Washer d10*φ20*2 Inner Cover U seat 30*10*1.5 Bolt ST4.2*8 Nylon nut M6*H6*S10 Belt...
- Page 6 ASSEMBLY INSTRUCTIONS STEP 1: A. Take out the bolts(14), spring washers(15) and washers(16) from front stabilizer (45) and rear stabilizer (48) by wrench (A). B. Attach front stabilizer (45) and rear stabilizer (48) to main frame(38) with the bolts(14), spring washers(15) and washers(16) by wrench(A).
- Page 7 STEP 2: A.Pull out knob(37) from main frame(38), not take it all out. Insert saddle tube(35) into main frame(38), adjust to suitable position and match with the hole of knob(37), then secure saddle tube(35) into main frame(38) using knob (37). B.Attach the saddle(21) into horizontal saddle tube(30), then secure them by spanner(B).
- Page 8 STEP 3: A.Take out the bolts(14), spring washers(15) and washers(16) from handlebar tube join(18) by wrench(A). B.Connect trunk wire 1(11) and trunk wire 2(19) well. C.Insert wire into computer post(10), then insert computer post(10) into handlebar tube join(18), and secure them using bolts(14), spring washers(15) and washers(16) by wrench (A).
- Page 9 STEP 4: A.Take out the bolts(13), spring washer(83) and washers(73) from horizontal handlebar tube(84) by spanner(B). B.Put horizontal handlebar tube(84) on the f ixed Plate of Horizontal handlebar tube(85) match the hole, then secur horizontal handlebar tube(84) in handlebar tube join(18) using the knob(68) and washers(73).
- Page 10 STEP 5: A. Unlock 4 bolts(3) from computer(1) by spanner(B). B. Connect wire(1a) and trunk wire 1(11) well. C. Secure computer(1) on computer holder(2) with 4 bolts(3) by spanner(B). D. Secure pedal (36L/R) into crank(89L/R) by spanner(B).
- Page 11 STEP 6: A. Unlock olts(57) from main frame(38) by spanner(B). B. Secure bottle holder(106) in the main frame using bolts(57) by spanner(B).
-
Page 12: Moving The Machine
MOVING THE MACHINE To move the machine, push the handlebar join(17) until the transportation wheels on the front stabilizer(45) touch the ground. With the wheels on the ground, you can transport the bike to the desired location with ease. ADJUSTMENTS GUIDE 1. - Page 13 2. ADJUSTING THE BALANCE When this product is on an uneven surface, please adjust both foot pads (47) according to the instruction picture. 3. ADJUSTING THE SADDLE Rotate knob(37) counter-clockwise adjust the height according as holes with red up and down arrow mark on saddle tube(35).
-
Page 14: Battery Replace
EXERCISE COMPUTER WITH PULSE INSTRUCTION MANUAL BUTTONS 1. MODE Press it to select functions . FUNCTIONS 1.SPEED Display instantaneous speed and the range is 0.0~99.9KM/H.Or,if the monitor showing M, the range will be 0.0~99.9MILE/H.The max. pickup signal is 1500rpm. Display current repetition per minute(RPM) during exercise. It reflects the pedal frequency. - Page 15 GARLANDO SPA Via Regione Piemonte, 32 - Zona Industriale D1 15068 - Pozzolo Formigaro (AL) - Italy www.toorx.it - info@toorx.it...