Garlando TOORX SRX80 EVO Instructions Manual
  1. Manuals
  2. Brands
  3. Garlando Manuals
  4. Exercise Bike
  5. TOORX SRX80 EVO
  6. Instructions manual

Garlando TOORX SRX80 EVO Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION

Advertisement

Table of Contents
loading

Related Manuals for Garlando TOORX SRX80 EVO

Summary of Contents for Garlando TOORX SRX80 EVO

  • Page 1 INSTRUCTION...

  • Page 2: Explosive View

    EXPLOSIVE VIEW...

  • Page 3: Parts List

    PARTS LIST PART NO. DESCRIPTION Computer 1 PC Bottle cage 1 PC Carriage bolt 1 PC Handlebar 1 PC Brake knob 1 PC Brake trim cover 1 PC Hexagon nut M8 2 PCS Brake rod φ10x290 1 PC Bushing plastic 1 PC Square nut 1 PC...
  • Page 4 27(L+R) Crank (L+R) 1 SET 28(L+R) Pedal(L+R) 1 SET Crank plug 2 PCS Flange nut M10 2 PCS Bushing 1 PC Crank plug 2 PCS Hexagon nut M10 4 PCS Foot pad 4 PCS Rear tube 1 PC Bearing6004 2 PCS Washer 2 PCS Chain Cover (inner)
  • Page 5 Adjust φ12 2 PCS Washer 1 PC Hexagon nut M12 3 PCS Flywheel axle 1 PC Flywheel 1 PC Bearing 6203 3 PCS Washer 2 PCS Drive pipe φ12x145 1 PC Screw M5x8 2 PCS Brake pad 1 PC Flywheel trim cover 1 PC Handlebar post 1 PC...

  • Page 6: Assembly Instruction

    ASSEMBLY INSTRUCTION STEP 1 Attach the rear tube (35) to the main frame(52) using two sets of screws(26). Attach the front tube (47) to the main frame same as the rear tube.
  • Page 7 STEP 2 Put seat post (17) insert main frame(52) with L knob (41)adjust height. Put seat (15) on the slider(16) and fix it. Fix the slider on the seat post by carriage bolt (3),washer(18)and knob(19).
  • Page 8 STEP 3 The pedals (28L and 28R) are marked “L” and “R”-left and right. Connect them to their appropriate crank set. The right crank set is on the right hand side of the cycle as you sit on it. Note that the Right pedal should be threaded on clockwise and the left pedal on anti-clockwise.
  • Page 9 STEP 4 Put handlebar(67) insert main frame with L knob (41)adjust height. Put computer(1) into handlebar(4), and fix handlebar on handlebar post using washers(71),and L knob. And then insert the sensor plug (14) into the sensor joint of computer. Now your spinning bike is finished for use.

  • Page 10: Front View

    EXERCISE MONITOR INSTRUCTION MANUAL FRONT VIEW HOW TO REMOVE BATTERY: 1. Pull off the battery cover and place one of CR2032 3V battery into battery housing on back of monitor, please refer to below illustrations. 2. Insure batteries are correctly positioned and battery springs are in proper contact with batteries.

  • Page 11: Key Guide

    KEY GUIDE ENTER: 1. Press this button to enter setting mode. Normal→Time→DIST→CAL→T.H.R 2. Press this button to confirm the setting values 3. Hold 3 seconds to reset all of the values to zero. Increase the setting value of the following functions. Time→DIST→CAL→T.H.R DOWN: Decrease the setting value of the following functions.
  • Page 12 CALORIE: press the button of ENTER to CAL function and press the UP or DOWN button to enter the value you want. Count up: Without setting the distance value, the monitor will count up the distance from 0.1~999.0. Count down: Setting the exercise calorie from 1.0~999, the monitor will count down from your setting values.
  • Page 13 GARLANDO SPA Via Regione Piemonte, 32 - Zona Industriale D1 15068 - Pozzolo Formigaro (AL) - Italy www.toorx.it - info@toorx.it...

Table of Contents