Rev-A-Shelf Soft-Close Pullout with blum Tandem slides with BluMotion Quick Start Manual

PART LIST
A- SLIDES
B- SLIDE STRAPS
C- RELEASE LEVERS
Lock Nut
Fig 5
D- PULLOUT CHASSIS
E- REAR SLIDE CATCH
F- PLASTIC SPACER
G- (4) #6 X 1/2" EURO SCREWS G- (4) #6 X 1/2" EURO SCREWS
H- (4) #3 X 1/2" COUNTERSUNK HEAD SCREWS
I - SCREW PACK 308
Lock Nut
Fig 6
Fig 7A
Fig 5
Fig 6
Fig 7B
Fig 6A
Fig 7A
Fig 6B
Fig 7B
Note: if inset application,
move the template back
the thickness of the door
T-532208-TRI-0416
T-5322-0416
5322-0416
3/32"
D D
Fig 4
Fig 5
Assemble the slide assembly to the oor of cabinet using the (8) #6 x 1" Phillips Flat Head Screw (Screw Pack 308 - F1606-22-1). Assemble the slide assembly to the oor of cabinet using the (8) #6 x 1" Phillips Flat Head Screw (Screw Pack 308 - F1606-22-1).
Note that the screws use the inner set of holes on the plastic feet. (See Fig 2) Note that the screws use the inner set of holes on the plastic feet. (See Fig 2)
Assemble the release levers and the rear slide catch (See Fig 3). Assemble the release levers and the rear slide catch (See Fig 3).
(Note: Be sure that the rear slide catch is assembly in the right position, when it is installed you have to see the plastic part with (Note: Be sure that the rear slide catch is assembly in the right position, when it is installed you have to see the plastic part with
number 18(See Fig 3a)) number 18(See Fig 3a))
Note: Approximately 2" from the fully closed position, there will be a slight bump. It is best to tilt the unit forward just a bit to aid in engagement. Note: Approximately 2" from the fully closed position, there will be a slight bump. It is best to tilt the unit forward just a bit to aid in engagement.
Loosen the (2) lock nuts at the back of the unit to allow the rear stop to oat freely (See Fig 4). Move the rear stop until it catches the Loosen the (2) lock nuts at the back of the unit to allow the rear stop to oat freely (See Fig 4). Move the rear stop until it catches the
rear of the face frame (if frameless application, a block may need to be added to allow the stop work properly). Once the stop is at the rear of the face frame (if frameless application, a block may need to be added to allow the stop work properly). Once the stop is at the
right position, the lock nuts can be tightened and bumpers can be added to the front of the stops. right position, the lock nuts can be tightened and bumpers can be added to the front of the stops.
If the door needs to be adjusted sideways, loosen the (4) lock nuts and adjust the door . (See Fig 6) If the door needs to be adjusted sideways, loosen the (4) lock nuts and adjust the door . (See Fig 6)
5) 5)
See Fig. 7A and 7B for tilt and hight adjustment See Fig. 7A and 7B for tilt and hight adjustment
Note: if inset application,
move the template back
the thickness of the door
For 8" Wide Pullout
3/32"
A- SLIDES
B- SLIDE STRAPS
C- RELEASE LEVERS
D- PULLOUT CHASSIS
E- REAR SLIDE CATCH
F- PLASTIC SPACER
G- (4) #6 X 1/2" EURO SCREWS G- (4) #6 X 1/2" EURO SCREWS
H- (4) #3 X 1/2" COUNTERSUNK HEAD SCREWS
I - SCREW PACK 308
B B
F
C C
A A
E E
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
PART LIST
G G
F
H H
I I
Fig 3a Fig 3a
Lock Nut Lock Nut