Advertisement
Quick Links
SainSmart Coreception 3D Printer Trouble Shooting
1. Cura settings (specifically print head size settings and why they are)
There is a known bug for the x-min and the y-min. These settings are used to set the hot
end size for the options to print all at once or island. This is not a concern with the
coreception as the print dimensions takes into account the size of the print head.
·For versions that do not allow the recommended settings use the below:
·x min = 0
·y min = -10
·x max = 10
·y max =10
www.sainsmart.com
support@sainsmart.com
Property of SainSmart.com. Unlawful to copy or reproduce in any manner without the express written consent.
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for SainSmart Coreception
Summary of Contents for SainSmart Coreception
- Page 1 ·For versions that do not allow the recommended settings use the below: ·x min = 0 ·y min = -10 ·x max = 10 ·y max =10 www.sainsmart.com support@sainsmart.com Property of SainSmart.com. Unlawful to copy or reproduce in any manner without the express written consent.
- Page 2 ) MKS provides multiple flavors of firmware for the MKS robin nano 1.2 board that is used in www.sainsmart.com support@sainsmart.com Property of SainSmart.com. Unlawful to copy or reproduce in any manner without the express written consent.
- Page 3 ·If all connections are in place and not broken wires are observed it may be a component failure. Image via 3dwork.io www.sainsmart.com support@sainsmart.com Property of SainSmart.com. Unlawful to copy or reproduce in any manner without the express written consent.
- Page 4 To the selected location of the remote extruder. The new cable should connect to the Motor e0 pictured below. ·Example T-slot nut assortment from amazon. Click here. www.sainsmart.com support@sainsmart.com Property of SainSmart.com. Unlawful to copy or reproduce in any manner without the express written consent.
- Page 5 14. Jerking or no movement on 1 or more axis or Z lead screws. ·This is typically a failure of the stepper driver or a disconnected motor cable. www.sainsmart.com support@sainsmart.com Property of SainSmart.com. Unlawful to copy or reproduce in any manner without the express written consent.
- Page 6 In any case, please reach out to SainSmart support via support@sainsmart.com. www.sainsmart.com support@sainsmart.com Property of SainSmart.com. Unlawful to copy or reproduce in any manner without the express written consent.
- Page 7 Issue command G503 Locate the M92 E##. Should be 381.5 on the coreception if you have never changed it.
- Page 8 --default #Type of heat manager for this heatedBed. >PIDTEMPBED # 1:PID ; 0:bang-bang >DEFAULT_bedKp 10.00 --default >DEFAULT_bedKi 0.023 --default >DEFAULT_bedKd 305.4 --default www.sainsmart.com support@sainsmart.com Property of SainSmart.com. Unlawful to copy or reproduce in any manner without the express written consent.
- Page 9 >DEFAULT_bedKd 155.200 # --default By default on the coreception heatbed is set for bang mode. If you want to change it I would run the same as you do for the extruder. Just set a lower temp (max of 100) and we have to specify the bed.
- Page 10 Run the bed autotune: M303 E-1 S60 C8 Set the PID for the bed: M304 P118.480 I22.610 D155.200 To save: M500 To verify use M503. www.sainsmart.com support@sainsmart.com Property of SainSmart.com. Unlawful to copy or reproduce in any manner without the express written consent.
- Page 11 Property of SainSmart.com. Unlawful to copy or reproduce in any manner without the express written consent.
Need help?
Do you have a question about the Coreception and is the answer not in the manual?
Questions and answers