Table of Contents
Advertisement
Quick Links
Advertisement
Chapters
Table of Contents
Related Manuals for Kyoeisha BARONESS LM56GC
Summary of Contents for Kyoeisha BARONESS LM56GC
- Page 1 Walk Behind Greens Mower Walk Behind Tee Mower Owner's Operating Manual Serial No. LM56GC: 35341-・LM66GC : 35351- LM66TC: 35071- "Required reading" Read this manual and the Owner's Manual for the engine before using the machine. Original Instructions Ver.2.0...
- Page 2 LM56GC・LM66GC / LM66TC Greeting Thank you for purchasing the Baroness product. This manual describes the proper handling, adjustment, and inspection of your product. We hope you will use the product safely, and take advantage of its best performance.
- Page 3 When making inquiries about the product, please specify the product's model designation and serial number. When loaning or transferring the product, please also provide this manual together with the product. Kyoeisha Co., Ltd. Warning Symbols This manual uses the following warning symbols for handling precautions that are important for your safety.
- Page 4 When replacing parts, be sure to use genuine Baroness parts or parts designated by Kyoeisha. Note that the Baroness product warranty may not apply to defects caused by the use of parts from other companies.
-
Page 5: Table Of Contents
LM56GC・LM66GC / LM66TC Contents Safety .............. Page 1-1 Safe Operating Practices .......Page 1-2 Disposal ............Page 2-1 Recycle and Waste Disposal ......Page 2-2 Product Overview .......... Page 3-1 Specifications ..........Page 3-2 Names of Each Section ......... Page 3-8 Regulation Decals ..........Page 3-8 Safety Signs and Instruction Signs .... - Page 6 LM56GC・LM66GC / LM66TC Contents...
-
Page 7: Safety
LM56GC・LM66GC / LM66TC Safety Safe Operating Practices ...... Page 1-2 Training ..........Page 1-2 Preparation ..........Page 1-2 Operation ..........Page 1-3 Maintenance and Storage ..... Page 1-4 Page 1-1... -
Page 8: Safe Operating Practices
LM56GC・LM66GC / LM66TC Safety Failure to adequately follow these safety Preparation precautions may cause an accident resulting in injury or death. Evaluate the terrain to determine what accessories and attachments are needed to Danger Danger properly and safety perform the job. This product is designed to ensure safe Only use accessories and attachments operation and has been tested and inspected... - Page 9 LM56GC・LM66GC / LM66TC Safety Stop the engine in the following conditions. Operation Before refueling. Do not operate the engine in a confined Before removing the grass catcher/ space where dangerous carbon monoxide catchers. fumes can collect. Before making height adjustment unless Only operate in good light, keeping away adjustment can be made from the from holes and hidden hazards.
- Page 10 LM56GC・LM66GC / LM66TC Safety When transporting the machine on a truck or Use jack stands to support components a trailer, set the parking brake, stop the when required. engine, and fasten the machine to the truck Carefully release pressure from components with a rope or other suitable restraining with stored energy.
-
Page 11: Disposal
LM56GC・LM66GC / LM66TC Disposal Recycle and Waste Disposal ....Page 2-2 About Recycle ........Page 2-2 About Waste Disposal ......Page 2-2 Page 2-1... -
Page 12: Recycle And Waste Disposal
LM56GC・LM66GC / LM66TC Disposal Recycle and Waste Disposal About Recycle Recycling battery etc. is recommended for environmental conservation and economical use of resources. It may be required by local laws. About Waste Disposal Make sure that waste generated when servicing or repairing the machine is disposed of in accordance with local regulations. -
Page 13: Product Overview
LM56GC・LM66GC / LM66TC Product Overview Specifications ........Page 3-2 Specifications List ........Page 3-2 Sound Pressure Level ......Page 3-7 Sound Power Level ....... Page 3-7 Vibration Level ........Page 3-7 Carbon Dioxide (CO2) Emissions Measurement .........Page 3-7 Names of Each Section ......Page 3-8 Regulation Decals ........Page 3-8 Positions of Regulation Decals .... -
Page 14: Specifications
LM56GC・LM66GC / LM66TC Product Overview Specifications Specifications List LM56GC Model LM56GC Total with grass catcher 55.51 in 141 cm length Total Dimensions without travelling wheel 37.01 in 94 cm width Total Steering handle 45.67 in 116 cm height Total weight (empty fuel tank) 224.87 lb 102 kg 7.28 lb... - Page 15 LM56GC・LM66GC / LM66TC Product Overview Working width 19.84 in 50.4 cm Dethatching Reel Number of Blades Working width 19.29 in 49.0 cm Rotary Brush Turning Diameter 2.36 in 6.0 cm The factory default maximum engine rpm is 3,400 rpm. Total weight includes parts.
- Page 16 LM56GC・LM66GC / LM66TC Product Overview LM66GC Model LM66GC Total with grass catcher 55.51 in 141 cm length Total Dimensions without travelling wheel 40.55 in 103 cm width Total Steering handle 45.67 in 116 cm height Total weight (empty fuel tank) 240.30 lb 109 kg 7.94 lb...
- Page 17 LM56GC・LM66GC / LM66TC Product Overview The factory default maximum engine rpm is 3,400 rpm. Total weight includes parts. The indicated lowest mowing height is for general application. It may be adjusted according to the state of green and the bed knife to be installed. The value in the brackets [ ] is the mowing height of the machine equipped with a groomer.
- Page 18 LM56GC・LM66GC / LM66TC Product Overview LM66TC Model LM66TC Total with grass catcher 55.51 in 141 cm length Total Dimensions without travelling wheel 40.55 in 103 cm width Total Steering handle 45.67 in 116 cm height Total weight (empty fuel tank) 235.89 lb 107 kg 7.94 lb...
-
Page 19: Sound Pressure Level
LM56GC・LM66GC / LM66TC Product Overview The factory default maximum engine rpm is 3,400 rpm. Total weight includes parts. The indicated lowest mowing height is for general application. It may be adjusted according to the state of green and the bed knife to be installed. The value in the brackets [ ] is the mowing height of the machine equipped with a groomer. -
Page 20: Names Of Each Section
LM56GC・LM66GC / LM66TC Product Overview Names of Each Section Regulation Decals Positions of Regulation Decals quwxcl-207 Positions of Regulation Decals_001 Serial number plate Specification decal Noise emission decal quwxcl-206 Year of manufacture decal Names of Each Section_001 Handle Description of Regulation Decals Throttle lever Serial Number Plate Engine switch... -
Page 21: Safety Signs And Instruction Signs
Part numbers for decals that need to be replaced are listed in the parts catalog. Order them from a Baroness dealer or Kyoeisha. kj8jic-001 Positions of Safety Decals and Instruction Specification Decal_001 Decals... -
Page 22: Description Of Safety Decals And Instruction Decals
LM56GC・LM66GC / LM66TC Product Overview Description of Safety Decals and Caution to Mutilation Decal Instruction Decals K4205001600 Caution Safety Instruction Decal DECAL, CAUTION TO MUTILATION Warning K4205001590 DECAL, CAUTION SAFETY INSTRUCTION May cut your hand or leg - Stop the cutter rotation and engine. - Page 23 LM56GC・LM66GC / LM66TC Product Overview Engine Oil Warning Decal K4205001300 DECAL, WARNING ENGINE OIL Important Check engine oil and gearbox levels before starting. W A R N I N G CHECK ENGINE OIL AND GEARBOX LEVELS BEFORE STARTING aajwhn-001 Engine Oil Warning Decal_001 Greasing Each 10-Hours Decal K4209000370 DECAL, GREASING EACH 10-HOURS...
- Page 24 LM56GC・LM66GC / LM66TC Product Overview Page 3-12 Safety Signs and Instruction Signs...
-
Page 25: Handling Instructions
LM56GC・LM66GC / LM66TC Handling Instructions Preparation for Use ....... Page 4-2 Engine Switch ........Page 4-22 Throttle Lever ........Page 4-22 Installing The Handle ......Page 4-2 Throttle Lever ........Page 4-23 Connection of Engine Switch Cord ..Page 4-2 Brake Lever ......... Page 4-23 Installing The Stand ....... -
Page 26: Preparation For Use
LM56GC・LM66GC / LM66TC Handling Instructions Preparation for Use Installing The Handle Put the handle pin on the left frame into the hole at the left-side lower edge of the handle. While pressing the right-side lower edge of the handle inward, put the handle pin of the right frame into the hole. -
Page 27: Inspections
LM56GC・LM66GC / LM66TC Handling Instructions Tighten the bolt, washer, and nut at the left Make sure that the reel cutter (cutting side of the stand that were temporarily cylinder) and the bed knife (bottom blade) secured. are not cracked. Check to see how much the reel cutter (cutting cylinder) and the bed knife (bottom blade) are worn. -
Page 28: Air Cleaner
LM56GC・LM66GC / LM66TC Handling Instructions Remove dirt and dust from the paper Air Cleaner element with blowing air or patting. Inspection of Air Cleaner Assemble the paper and urethane elements. The air cleaner is a component that removes Attach the air cleaner elements with the dirt from the intake air to prevent wear of the screw. -
Page 29: Roller
LM56GC・LM66GC / LM66TC Handling Instructions Roller Wire Inspection of Rollers Inspection of Wire Bearing wear due to frequent use or bearing Make sure that the wire is not cracked or damage caused by water infiltration may damaged. prevent the roller from rotating smoothly. If the wire is cracked or damaged, replace it Inspect the roller and, if necessary, replace with a new one immediately. -
Page 30: Fuel
LM56GC・LM66GC / LM66TC Handling Instructions The appropriate engine oil level should be Screw the oil level gauge firmly. between the upper and lower limit lines on the gauge. bgmiun-019 Supply of Engine Oil_001 bgmiun-015 Oil level gauge (Oil filling port) Inspection of Engine Oil_002 Drain plug Oil level gauge... -
Page 31: Oil Leakage
LM56GC・LM66GC / LM66TC Handling Instructions Oil Leakage Fuel Supply Inspection of Oil Leakage Caution After approximately 50 hours of operation, Do not supply fuel above FULL level of the some joints may be loosened and oil and fuel gauge. grease may leak. If you supply too much fuel, it might overflow Be sure to retighten the parts. -
Page 32: Tightening Torques
LM56GC・LM66GC / LM66TC Handling Instructions Tightening Torques Important Refer to the Tightening Torque table. Note that the Baroness product warranty may not apply to defects caused by incorrect or overtorque tightening, etc. Standard Tightening Torques Bolts and Nuts Important A number of bolts are used in each part of this machine. Be sure to re-tighten the bolts and nuts, because they may be loosened at the earlier stage of the use. - Page 33 LM56GC・LM66GC / LM66TC Handling Instructions General bolt Strength classification 4.8 Nominal diameter tib3yb-001 kgf-cm lb-in 3 - 5 30.59 - 50.99 26.55 - 44.26 7 - 9 71.38 - 91.77 61.96 - 79.66 14 - 19 142.76 - 193.74 123.91 - 168.17 29 - 38 295.71 - 387.49 256.68 - 336.34...
-
Page 34: Principal Tightening Torques
LM56GC・LM66GC / LM66TC Handling Instructions Principal Tightening Torques Tightening Torque by Model LM18GC/LM56GC/LM66GC/LM66TC Tighten the following bolts and nuts at the torque specified in the table. For thread locking adhesive, apply a middle strength thread locker (ThreeBond 1322 or equivalent anaerobic sealant). -
Page 35: Adjustment Before Work
LM56GC・LM66GC / LM66TC Handling Instructions Adjustment before Work Adjustment of Handle The height of the handle can be adjusted according to the operator's working position. Move the handle adjusters supporting the handle up or down and fix them with the bolts. gp7sf7-001 Adjustment of IGCA (Independent Grass Catcher Arm)_001 Handle pipe... -
Page 36: Adjustment Of Blade Engagement
LM56GC・LM66GC / LM66TC Handling Instructions Tighten the right and left locknuts. Link rod Snap pin Washer Flat head pin L-shape bracket Nut A Nut B Repeat the same process for adjustment of the opposite link rod. Adjustment of gap for the grass catcher: gp7sf7-004 Adjustment of IGCA (Independent Grass Catcher Arm)_004 Important... -
Page 37: Adjustment Of Cutting Height
LM56GC・LM66GC / LM66TC Handling Instructions With the cutter adjustment nut, adjust the Adjustment of Cutting Height engagement between the reel cutter (cutting cylinder) and the bed knife (bottom blade) so Adjust the cutting height to fit your cutting work. that newspaper (one sheet) will be cleanly Important cut by the edge of both blades when the blades in their entirety come slightly into... - Page 38 LM56GC・LM66GC / LM66TC Handling Instructions Thickness of Rough minimum blade Type Blade type cutting height Code Part name Remarks (mm/inch) (mm/inch) K2511000490 1 Bed knife 22 1.0/0.039 2.5/0.098 K2511000510 1 Bed knife 22-44.5 Offset 2.5 mm K2511000270 1.5 Bed knife 55G ...
- Page 39 LM56GC・LM66GC / LM66TC Handling Instructions Move the front roller up or down with the Adjustment of Front Roller roller adjuster to position the front roller so that there is no gap between the bottom of You can adjust the cutting height by moving the head of the small screw for cutting the front roller up or down.
-
Page 40: Adjustment Of Groomer
LM56GC・LM66GC / LM66TC Handling Instructions Adjustment of Groomer Dethatching blade Small screw for groomer setup Note: Cutting height gauge Depending on the specifications, this function Front roller may not be available. Groomer height Important Loosen the nuts securing the left and right If the front groomer is being used, adjust it groomer adjustment screws. -
Page 41: Procedure To Start/Stop Engine
LM56GC・LM66GC / LM66TC Handling Instructions Next time the groomer is used, loosen the Cutting height gauge right and left nuts, lower the groomer and Small screw for cutting height setup tighten the nuts so that it can return to the Fly nut groomer height set previously. - Page 42 LM56GC・LM66GC / LM66TC Handling Instructions Set the engine switch to the "ON" position. Brake lever Lock lever Lock Unlock Don't grip the main clutch lever. v2e27i-043 Procedure to Start Engine_005 Engine switch k7k67l-004 Set the choke lever to the "Close" position. Procedure to Start Engine_003 Main clutch lever Clutch lock lever...
- Page 43 LM56GC・LM66GC / LM66TC Handling Instructions Procedure to Stop Engine Important Return the starter grip slowly to its original Don't grip the main clutch lever. position after the engine starts. Do not let go of the pulled starter grip since it may cause damage to the machine.
-
Page 44: Operation Method
LM56GC・LM66GC / LM66TC Handling Instructions Positions of Operation Decals Fuel cock Close Open Operation Method Cautions before Leaving The Machine Caution Park the machine on a flat place. Do not park the machine on a slope. Caution Check that the engine has stopped. Caution Make sure that the brake lever is locked. -
Page 45: Description Of Operation Decals
LM56GC・LM66GC / LM66TC Handling Instructions Description of Operation Decals Groomer Indication Mark Engine Switch Mark Note: Depending on the specifications, this function may not be available. ENGINE SWITCH MARK K4203001120 It illustrates the positions of the engine switch. DECAL, GROOMER INDICATION It illustrates the changeover of rotational direction of the groomer. -
Page 46: Light Switch
LM56GC・LM66GC / LM66TC Handling Instructions Engine Switch Red Alignment Mark 10300 Note: The engine switch is located in the handle. Depending on the specifications, this function To start the engine, set the engine switch to may not be available. the “ON” position, and to stop it, set to the K4209001230 “OFF”... -
Page 47: Brake Lever
LM56GC・LM66GC / LM66TC Handling Instructions Throttle Lever Note: Depending on the specifications, this function may not be available. The throttle lever is located in the handle and enables you to adjust the engine rpm. Move the throttle knob toward the "High speed" position to increase the engine rpm, and toward the "Low speed"... -
Page 48: Main Clutch Lever
LM56GC・LM66GC / LM66TC Handling Instructions Main Clutch Lever Traveling/Working Selector Lever Caution Caution Avoid quick operation. This lever should be operated while the main Carefully and slowly operate the machine. clutch lever is set to the disengaged position, and adjusted to the position suitable for your work. -
Page 49: Air Adjusting Plate
LM56GC・LM66GC / LM66TC Handling Instructions Air Adjusting Plate Engine Clutch Cover The engine clutch cover is located on the left Caution side of the engine and covers the engine clutch. The air adjusting plate should be operated Open or close the engine clutch cover by while the engine rotation is stopped, and removing or installing the lock bolt. -
Page 50: Igca (Independent Grass Catcher Arm)
LM56GC・LM66GC / LM66TC Handling Instructions Issue 1: The cutting height fluctuates due to the up- and-down movements of the mower caused by the weight of the grass catcher. Solution: The mower and grass catcher operate independently. Therefore, the mowing attitude of the mower is not affected, even when the grass catcher becomes heavier from the aqilnf-001... -
Page 51: Instruments
LM56GC・LM66GC / LM66TC Handling Instructions Effect 2: Since the load of the grass catcher does not affect the front roller, it is possible to reduce sinking (gouging or digging) caused by the front roller touching the ground when entering the green. 4fx8ud-003 IGCA (Independent Grass Catcher Arm)_003 IGCA... -
Page 52: Travel Of Machine
LM56GC・LM66GC / LM66TC Handling Instructions Move the air adjusting plate to the desired Travel of Machine position. Traveling Procedure Move the groomer clutch lever to the desired position. Caution Make the traveling/working selector lever to the "Reel ON" position. Under any circumstances drive the machine at Start the engine. -
Page 53: Removing/Installing Traveling Tires
LM56GC・LM66GC / LM66TC Handling Instructions Removing/Installing Traveling Tires Important Mow with the traveling tires removed. Use the traveling tires to move the machine by self-propelling. Removal of traveling tires: Set the machine on its stand. x9pzjh-003 Removing/Installing Traveling Tires_003 Traveling tires Follow the same steps to remove the traveling tire on the opposite side. -
Page 54: Transporting
LM56GC・LM66GC / LM66TC Handling Instructions Transporting Important Make sure that the wheel mounting plate fits Transporting Procedure into the groove in the drum shaft. If they do not engage, the wheel may fall off. Caution When loading and unloading the machine, wear non-slip shoes and travel slowly. -
Page 55: Maintenance
LM56GC・LM66GC / LM66TC Maintenance Maintenance Precautions ..... Page 5-2 Position of Mower during Maintenance ........... Page 5-2 Maintenance Schedule ......Page 5-3 Adjusted Values ........Page 5-5 Greasing ..........Page 5-6 About Greasing ........Page 5-6 Greasing Points ........Page 5-6 Lubrication ..........Page 5-8 About Lubrication ........Page 5-8 Lubricating Points ........ -
Page 56: Maintenance Precautions
LM56GC・LM66GC / LM66TC Maintenance Maintenance Precautions Caution First, learn well the maintenance operations you plan to perform. Important Use tools appropriate for each maintenance operation. Important For the safe and best performance of your machine, use Baroness genuine parts for replacement and accessories. -
Page 57: Maintenance Schedule
LM56GC・LM66GC / LM66TC Maintenance Maintenance Schedule LM18GC/LM56GC/LM66GC/LM66TC Follow the maintenance schedule below. ○・・・Inspect, adjust, supply, clean ●・・・Replace (first time) △・・・Replace Maintenance Item Remarks Check tightening bolts and nuts ○ ... - Page 58 LM56GC・LM66GC / LM66TC Maintenance Maintenance Item Remarks Check tire pressures and ○ condition Check damaged parts ○ ...
-
Page 59: Adjusted Values
LM56GC・LM66GC / LM66TC Maintenance Maintenance Item Remarks Replace front roller oil seals △ Replace grease inside gearcase △ ... -
Page 60: Greasing
LM56GC・LM66GC / LM66TC Maintenance Greasing No. of Greasing Location greasing period About Greasing points Frame & Transmission 7 Since there may be adhesion or damage due Differential gear to lack of grease on moving parts, they must be greased. Reel bearing Add urea-based No. - Page 61 LM56GC・LM66GC / LM66TC Maintenance Differential gear Front roller There is one point each on the left and right. Right side 8bq62b-327 Greasing Points_004 Reel bearing 8bq62b-250 Before the initial greasing, remove the elastic Greasing Points_007 adhesive on the tips of the grease nipples Left side with a flat-blade screwdriver, etc.
-
Page 62: Lubrication
LM56GC・LM66GC / LM66TC Maintenance Handle No. of Main clutch lever ･ Location greasing points Clutch lock lever fulcrum Throttle lever fulcrum Clutch lock lever fulcrum 8bq62b-447 Greasing Points_010 Lubrication About Lubrication 9llqa9-041 It is necessary to lubricate moving parts so that Lubricating Points_002 they will not become stuck or damaged. -
Page 63: Maintenance Work
LM56GC・LM66GC / LM66TC Maintenance Check for the gap between the reel cutter Maintenance Work (cutting cylinder) and the bed knife (bottom blade). Adjustment of Cutter Adjustment Spring Loosen the locknut when adjusting the cam bush. Caution Both the reel cutter (cutting cylinder) and the bed knife (bottom blade) are edged tools. -
Page 64: Back Lapping
LM56GC・LM66GC / LM66TC Maintenance Center of cutter pin Center of cam bush Punch mark 0.3 mm (0.012 in) Raising the bed knife Lowering the bed knife. Back Lapping Back lapping is work similar to sharpening a zhz6po-002 cooking knife. If the edges of the reel cutter Back Lapping_001 (cutting cylinder) and the bed knife (bottom blade) become blunt and make cutting difficult,... - Page 65 LM56GC・LM66GC / LM66TC Maintenance Connect the lapping machine or lapping Traveling/Working selector lever handle to the lapping bolt of the machine. Reel ON Travel ON Travel OFF Insert one or two strips of newspaper into the space between the reel cutter (cutting cylinder) and the bed knife (bottom blade) at an angle of 90 degrees.
-
Page 66: Sharpening Of Reel Cutter (Cutting Cylinder)
LM56GC・LM66GC / LM66TC Maintenance Remove the lapping machine or lapping For sharpening the reel cutter (cutting handle. cylinder), contact your dealer or Baroness. If the outer diameter of the reel cutter (cutting Wash off or wipe off with a cloth, etc., the cylinder) after sharpening is more than the abrasive from the reel cutter (cutting usage limit, the reel cutter (cutting cylinder) can... -
Page 67: Replacement Of Reel Cutter (Cutting Cylinder)
LM56GC・LM66GC / LM66TC Maintenance Sharpening is necessary when the reel cutter The criteria for replacing the reel cutter (cutting (cutting cylinder) reaches a condition described cylinder) are described below. below. However, these criteria are only a reference and do not guarantee performance like that of When the sharpening width (length of a new reel cutter (cutting cylinder). - Page 68 LM56GC・LM66GC / LM66TC Maintenance Installing The Reel Cutter (Cutting Cylinder) Washer Left-hand nut Caution Torque wrench 11.5 mm (0.453 in) Both the reel cutter (cutting cylinder) and the bed knife (bottom blade) are edged tools. Specification with groomer: Handle them carefully, since they could cut your hands and feet.
-
Page 69: Replacement Of Bed Knife (Bottom Blade)
LM56GC・LM66GC / LM66TC Maintenance Replacement of Bed Knife (Bottom Blade) Caution Both the reel cutter (cutting cylinder) and the bed knife (bottom blade) are edged tools. Handle them carefully, since they could cut your hands and feet. Caution d5gd5v-003 Wear gloves when touching edged tools to Replacement of Bed Knife (Bottom Blade)_002 avoid cutting your hands. - Page 70 LM56GC・LM66GC / LM66TC Maintenance Remove the 2 bolts that secure the bed Remove the bed knife base COMP. knife base arm Assy and bed knife base COMP. 5ttm1g-004 Removing The Bed Knife Base_004 5ttm1g-002 Bed knife base COMP Removing The Bed Knife Base_002 Bed knife base COMP Bolt Important...
- Page 71 LM56GC・LM66GC / LM66TC Maintenance Installing The Bed Knife Base Important Install the bed knife base arm Assy parallel to Caution the frame. During installation, be careful not to twist both Both the reel cutter (cutting cylinder) and the arms. bed knife (bottom blade) are edged tools. Handle them carefully, since they could cut Insert the bed knife base arm Assy into the your hands and feet.
- Page 72 LM56GC・LM66GC / LM66TC Maintenance Remove the fulcrum seat bolt used to Insert one or two strips of newspaper into temporarily install the bed knife base arm. the space between the reel cutter (cutting Note: cylinder) and the bed knife (bottom blade) With the weight of the bed knife base arm, at an angle of 90 degrees.
- Page 73 LM56GC・LM66GC / LM66TC Maintenance Important Important If one to five gap adjustment washers had Make sure that the cam bush does not move been inserted between the fulcrum seat and from the marked position. the frame, insert gap adjustment washers so Tighten the lock nuts of the left and right that the gap is eliminated.
-
Page 74: Removing/Installing The Bed Knife
LM56GC・LM66GC / LM66TC Maintenance Removing/Installing The Bed Knife Installing The Bed Knife Removing The Bed Knife Caution Both the reel cutter (cutting cylinder) and the Caution bed knife (bottom blade) are edged tools. Both the reel cutter (cutting cylinder) and the Handle them carefully, since they could cut bed knife (bottom blade) are edged tools. -
Page 75: Removing/Installing The Small Cover (Left)
LM56GC・LM66GC / LM66TC Maintenance Unscrew the 4 bolts, and then detach the small cover (left). 4miqko-002 Installing The Bed Knife_002 xg9isz-006 Bed knife Removing The Small Cover (Left)_002 Screw Small cover (left) Removing/Installing The Small Cover (Left) Bolt Removing The Small Cover (Left) Installing The Small Cover (Left) Insert an item such as a wooden hammer Attach the small cover (left) temporarily to... -
Page 76: Adjustment Of Brake
LM56GC・LM66GC / LM66TC Maintenance Insert an item such as a wooden hammer Make sure that the brake shoe does not handle into the reel cutter to prevent it from touch the brake drum. turning, and install the disk spring and the Avoid the brake always being engaged. - Page 77 LM56GC・LM66GC / LM66TC Maintenance Insert a thickness gauge (accessory tool) After appropriate adjustment of the between the engine clutch and the clutch operation distance of the clutch plate facing. completed, tighten the clutch wire Make adjustment of the engine position adjusting nuts.
-
Page 78: Change Of Air Cleaner
LM56GC・LM66GC / LM66TC Maintenance Tighten the lock nut. Important Be sure to use engine oil that is classified as API Service Grade SE or higher, with an SAE Viscosity that is appropriate for the operating environment (ambient temperature). Important Screw the oil level gauge firmly. Replace the engine oil more frequently if the wdzf6u-004 engine oil is contaminated, and especially if... -
Page 79: Troubleshooting Procedures Of Aftercut Appearance
LM56GC・LM66GC / LM66TC Maintenance Angled Mismatch Troubleshooting Procedures of Aftercut Appearance Is the cutting height on both sides adjusted to be the same? Scalping Adjustment of cutting height Is the roller bracket secured? Is the bed knife (bottom blade) chipped? Tightening to secure Replacement of securing screws Replacement of bed knife (bottom blade) -
Page 80: Overlap Marks
LM56GC・LM66GC / LM66TC Maintenance Overlap Marks Has the bed knife (bottom blade) become curved? Back lapping Surface grinding of bed knife (bottom blade) Replacement of bed knife (bottom blade) Loosening of blade engagement After loosening blade engagement, streaks still appear. Adjustment of spring compression length Is the spring pressure for the adjustment nut too light? (See "Adjustment of Cutter Adjustment Spring".) -
Page 81: Blade Does Not Cut
LM56GC・LM66GC / LM66TC Maintenance Blade Does Not Cut Are genuine parts used for the blades? Is the grit size of the lapping Use lapping powder with a grit Replacement of blades with genuine parts powder #200 – #400? size of #200 – #400. Is the blade face of the bed knife (bottom blade) too rough? Has topdressing sand recently Work in sand... -
Page 82: Uneven Blade Engagement
LM56GC・LM66GC / LM66TC Maintenance Uneven Blade Engagement The unevenness is a difference of tightening torque between the left and right cutter adjustment nuts, or blade engagement on only one side, which cannot be adjusted. Promptly resolve the issue in order to maintain the optimum performance of the machine. - Page 89 1-26, Miyuki-cho, Toyokawa-city, Tel : +81 - 533 - 84 - 1390 Head Office Aichi-pref, 442-8530 JAPAN Fax : +81 - 533 - 84 - 1220 LM56GC--UM--GBZ/20A-00-S.K E02[LM56_EU02/LM66_EU02]...
Need help?
Do you have a question about the BARONESS LM56GC and is the answer not in the manual?
Questions and answers