Environmental Protection; Technical Data - Metabo W 18 LT BL 11-125 Original Instructions Manual

reinforced concrete and masonry exclusively with
diamond cutting discs, without using water.
- Dust extraction shroud (see page 4 fig. K)
Designed for cutting through stone slabs with
diamond cutting discs. With nozzle for extracting
stone dust using a suitable extraction unit.
- Dust extraction shroud* for surface grinding
Intended for grinding of concrete, screed, wood and
plastics with diamond cup wheels and/or fibre discs
and suitable hook and loop sanding pads. With
nozzle for extracting stone, wood and plastic dust
using a suitable extraction unit. Not suitable for
extracting sparks or for grinding of metals (see page
4 fig. L).
- Multi-position bar (24) for side handle
Permits diverse handle positions (see page 4 fig.
M).
- Hand protection
Intended for work with backing pads, hook and loop
packing pads (sanding pads), wire brushes and
diamond drill bits for tiles.
Install the hand guard under the side handle (see
page 4 fig. N).
- Battery packs:
Order no.: 625368000 5.5 Ah (LiHD)
Order no.: 625369000 8.0 Ah (LiHD)
Order no.: 625549000 10.0 Ah (LiHD)
etc.
- Chargers: ASC 55, ASC 145, etc.
* May only be used in conjunction with the
2-hole nut
For a complete range of accessories, see
www.metabo.com or the accessories catalogue.
12. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.

13. Environmental Protection

The sanding dust generated may contain
hazardous materials: do not dispose of dust with
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Battery packs must not be disposed of with regular
waste! Please return faulty or used battery packs to
your Metabo dealer!
Do not throw battery packs into water.
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.
Discharge the battery pack in the power tool before
disposal. Prevent the contacts from short-circuiting
(e.g. by protecting them with adhesive tape).

14. Technical Data

Explanatory notes on the specifications on page 2.
Subject to change in accordance with technical
progress.
U = Voltage of battery pack
D =max. diameter of accessory
max
t = max. permitted thickness of the clamping
max,1
shank on accessory when using two-hole
nut (21)
t = max. permitted thickness of the clamping
max 2
shank on accessory when using a quick
clamping nut (1)
t = roughing disc/cutting disc:
max,3
max. permitted thickness of accessory
M = Spindle thread
l = Length of the sanding spindle
n = No-load speed (maximum speed)
n = no-load speed (adjustable)
v
P = Rated input power
1
P = Power output
2
m = Weight (with smallest battery pack)
Measured values determined in conformity with EN
60745.
direct current
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on operating conditions, the
condition of the power tool or the accessories used.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Total vibration value (vector sum of three directions)
determined in accordance with EN 60745:
a = Vibration emission value (surface
h, SG
grinding)
a = vibration emission value (sanding
h, DS
with hook and loop sanding pad)
K = Uncertainty (vibration)
h,SG/DS
Typical A-effective perceived sound levels:
L = sound-pressure level
pA
L = acoustic power level
WA
K , K = Uncertainty
pA WA
During operation the noise level can exceed 80
dB(A).
Wear ear protectors!
ENGLISH en
19