Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Neomatica ADM33
- Page 1 «Neomatica» Wireless sensor-immobilizer ADM33, edition 1.1 dd 11.11.2019...
-
Page 2: Table Of Contents
6. Handling and transport regulations ..................17 7. Warranty obligations ........................17 8. Marking and packaging ......................17 9. Disposal ............................17 10. Scope of supply ......................... 18 11. Acceptance certificate ......................18 «Neomatica» Wireless sensor-immobilizer ADM33, edition 1.1 dd 11.11.2019... - Page 3 This Operation manual relates to the wireless sensor-immobilizer ADM33 (hereinafter referred as immobilizer). The manual also describes the immobilizer operation with the tracker ADM 333 BLE manufactured by Neomatica LLC. The Operation manual is designed for professionals who have familiarized themselves...
-
Page 4: Application
Can be installed on vehicles to block electrical circuit of the ignition system or of the fuel supply in order to block the engine work or engine start-up. Can be installed on stationary objects as a switcher with wireless control. Fig. 1. ADM33 general view «Neomatica» Wireless sensor-immobilizer ADM33, edition 1.1 dd 11.11.2019... -
Page 5: Technical Features
Consumption current (at supply voltage of 12 V): 55мА when electromechanical relay is switched on; IP class: IP65; • • Body material: polyolefin; • Dimensions, mm: at most 17 x 21 x 80 (380 with cables); Weight: at most 34 g • «Neomatica» Wireless sensor-immobilizer ADM33, edition 1.1 dd 11.11.2019... -
Page 6: Operation Principle
3. Operation principle Immobilizer ADM33 consists of microcontroller, accelerometer, two semiconductor switches with current protection, electromechanical relay, Bluetooth LE radio interface. Microcontroller processes received commands via Bluetooth LE radio channel and controls semiconductor switches and electromechanical relay basing on these commands, signals from accelerometer and chosen operation algorithm. -
Page 7: Setting And Installation Order
Black cable (GND) must not exceed 2.6 A. To connect Red cable (+) use the main vehicle power source with steady voltage of 10 V up to 40 V. «Neomatica» Wireless sensor-immobilizer ADM33, edition 1.1 dd 11.11.2019... -
Page 8: Semiconductor Switches Mode
1. Red cable — + (plus of the power source); 2. Black cable — GND (minus of the power source); 3. Blue cable — is not used (should be isolated); 4. White cable — Output 1; 5. Brown cable —Output 2. «Neomatica» Wireless sensor-immobilizer ADM33, edition 1.1 dd 11.11.2019... -
Page 9: Electromechanical Relay Mode
“NC” is closed to the outlet “COM”. Functions of the outlets in electromechanical relay mode are indicated in figure 4. Fig. 4. ADM33. Scheme of contact elements when using electromechanical relay 1. Red cable — + (plus of the power source);... -
Page 10: Immobilizer Operation With The Tracker Adm333Ble
Fig 5. ADM33. Use of normally open contact elements for lockup Fig. 6. ADM33. Use of normally closed contact elements for lockup 4.2. Immobilizer operation with the tracker ADM333BLE The immobilizer is managed by the tracker. The setting of interaction between the immobilizer and the tracker ADM333 BLE (hereinafter referred as tracker) is performed by sending commands to the tracker via Bluetooth, GPRS and SMS. -
Page 11: Control Of Immobilizer Statuses
BLEOUTPUT 1 – set immobilizer status 1; 4.2.3. Setting immobilizer ADM33 Use BLEOUTCFG command to set the immobilizer. ADM33 stops Bluetooth environment scanning process and starts broadcasting Advertising messages. To configure settings and select immobilizer modes use a smartphone with operation system Android .5.0 or earlier as well as nRF Connect application. - Page 12 Now the immobilizer is ready to receive your commands. 12) To send commands click on the arrow pointing up, next to the field “RX Characteristic”. There will appear a window for entering the following commands: «Neomatica» Wireless sensor-immobilizer ADM33, edition 1.1 dd 11.11.2019...
-
Page 13: Reading Of The Immobilizer Current Settings
4.2.3.1. Reading of the immobilizer current settings • To read current parameters use command rs. The command sends response in the following form: «Neomatica» Wireless sensor-immobilizer ADM33, edition 1.1 dd 11.11.2019... - Page 14 The command sends response in the following form: rb: [parameter ID ]=[parameter value];[parameter ID ]=[parameter value] and etc. List of parameters ID: 1 — main firmware version. 2 — firmware version. 3 — type of device. 4- configuration version «Neomatica» Wireless sensor-immobilizer ADM33, edition 1.1 dd 11.11.2019...
-
Page 15: Command Description
Select emergency status of immobilizer 0 – COM+NC; 1 – COM+NO (by default). 10 ts Х – types of actions: Action to be performed at the absence of 0 – do nothing; connection with the tracker. «Neomatica» Wireless sensor-immobilizer ADM33, edition 1.1 dd 11.11.2019... - Page 16 X=4 – inversion of semiconductor switch 2 status; X=6 – inversion of semiconductor switches 1 and 2 status 14 sf Х Х – protection status. Activation of protection against messages substitute from the tracker 0 - off; 1 -on. «Neomatica» Wireless sensor-immobilizer ADM33, edition 1.1 dd 11.11.2019...
-
Page 17: Handling And Transport Regulations
8. Marking and packaging Marking is placed on the housing of wireless immobilizer ADM33. The immobilizer is packed in an individual package or in a multi package 9. Disposal Device recycling is performed according to national and local norms and requirements. -
Page 18: Scope Of Supply
Comments Wireless sensor-immobilizer ADM33 Passport 11. Acceptance certificate Wireless sensors-immobilizers ADM33, operation manual No. ШАИФ.464512.004 in quantity of _____ pcs are considered to be ready for operation. Date of manufacture: Manufacturer: Neomatica LLC 24а Malkova, office 7, Perm 614087, Russia Tel: +7 (342) 2-111-500 (ext.