Digital
BEVEL BOX
Angle Meter
Thank you for purchasing the Bevel Box Digital Angle Meter.
Please read this manual thoroughly before use for proper operation.
■PARTS IDENTIFICATION
【Rear】 Battery Cover
【Front】
[ LCD ] Display
[ ZERO ] Button
[ HOLD ] Button
【Bottom】
[ ON/OFF ] Button
Measurement Surface
CAUTION
●This is a precision measurement instrument - Handle With
Care. Do not drop or subject to shock.
●Instrument accuracy is listed under Specifications section.
For applications requiring higher accuracy, please use
higher precision angle gauge.
●Do not engrave or mark with electric pen.
●Holding power of magnet will vary depending on workpiece.
Test for sufficient holding force before use to insure
instrument does not fall.
●Keep away from precision instruments, watches, etc. and
any devices that can be damaged by magnet.
●Clean measuring surface with soft cloth after use to
remove any debris or contamination.
●Remove battery if gauge will not be used for a long period
of time.
●Do not use or store in places subject to extreme temperate
fluctuations, direct sunlight, dusty locations, or locations
that are wet or have high humidity.
■INSERTING / REPLACING the BATTERY
●1× AAA battery required ( not included. )
①Push on tab of rear battery
cover to open.
②Insert AAA battery as shown
in drawing. Replace cover.
+
INSTRUCTION MANUAL
Model No. : BB-180L
■APPLICATIONS and FEATURES
●Precision angle measurement and working
reference for assembly of machinery, tooling,
jigs, etc.
●Magnetic base.
●Absolute Mode for measuring angle referenced
to true horizontal.
●0-point can be set at any position in Relative
Mode.
●Hold function to freeze display.
●Auto Power Off feature. (approx. 5 minutes)
■SPECIFICATIONS
品 番
Model
Measurement Range
Resolution
Accuracy
Repeatability
Operating Temperature Range
approx. 5〜45℃
approx. 70g ( without battery )
Weight
AAA Battery ( 1× )
Power
approx. 40Hr. ( for alkaline battery )
Battery Life
Accessories
Storage Case
Absolute ( ABS ) , Relative
Measurement Modes
■LCD DISPLAY ( POWER ) ON / OFF
【To Turn ON Power】
When power is OFF, press [ ON/OFF ] Button.
【To Turn OFF Power】
When power is ON, long press of [ ON/OFF ]
Button.
【Auto Power Off Feature】
If there is no change in measured value for
approximately 5 min., power will turn OFF
automatically.
■ MEASUREMENT MODE
【Absolute Measurement Mode ( ABS ) 】
Battery
When power is ON, press [ ON/OFF ] button to
Cover
switch gauge to Absolute Mode. "ABS" icon will
appear on the LCD display.
Tab
【Relative Measurement Mode】
AAA
When power is ON, press [ ZERO ] button to
Battery
switch gauge to Relative Mode. The "ABS" icon
−
will turn off and display will reset to 0.0.
■TAKING MEASUREMENTS
When Taking Measurements, Please Note
●Place the measurement surface of the gauge onto the object to
be measured. ( Figure:1 )
※If off-axis tilt of the gauge (toward front or back sides) exceeds
±5°, a measurement can not be taken and "Erro" will be displayed
on the LCD.
A
bsolute Measurement Mode
①Press [ ON/OFF ] to turn on power.
②If "ABS" icon is not displayed, press [ ON/OFF ] again to switch
gauge to Absolute Measurement Mode and display icon.
③Place the measurement surface of the gauge onto the object to be
measured. ( Figure:2 )
Direction of tilt icon will display next to measured value -
If tilt is to left, ▼ icon will display.
If tilt is to right, ▲ icon will display.
Relative Measurement Mode
BB-180L
●In Relative Measurement Mode, 0° can be preset at any angle.
±180.0°
①Press [ ON/OFF ] to turn on power.
0.1°
②Place gauge on reference surface and press [ ZERO ] button.
± 0.2°
(
Figure:3 )
0.1°
③Place the measurement surface of the gauge onto the object to
be measured. ( Figure:4 )
Direction of tilt icon will display next to measured value -
If tilt is to left, ▼ icon will display.
If tilt is to right, ▲ icon will display.
④Press the [ON/OFF] Button again to switch back to Absolute
Measurement Mode.
HOLD FUNCTION
Press [ HOLD ] to fix the reading on the display.
Press [ HOLD ] a second time to release.
■ TROUBLESHOOTING
If any of the following symptoms appear, please cycle power by
removing and replacing battery, or replacing battery with a fresh one.
●No display.
●Displayed reading is in error.
●Displayed value does not change as gauge is moved.
※If problem persists, or if you have any questions, please contact distributor
or place of purchase.
※Please note, manufacturer is unable to respond to inquires or provide
service directly.
Please contact distributor or place of purchase.
( Figure: 1 )
ABS )
(
Tilted 10° to left
from horizontal
( Figure: 2 )
Display reading is 0.0°
2
( Figure: 3 )
Tilted 5° to left from
reference surface
( Figure: 4 )
Niigata seiki Co., Ltd.
5-3-14, Tsukanome, Sanjo, Niigata, Japan, 955-0055
Tel. : +81-256-33-5522 Fax. : +81-256-33-5518
MAIL intl.sales@niigataseiki.co.jp
URL
Surface to be Measured
Tilted 10° to right
from horizontal
1
[
]
Press
ZERO
Button
Reference Surface
ABS
Tilted 5° to right from
reference surface
http://www.niigataseiki.co.jp