Advertisement
Module G1 / G3
NORMAL TIME DISPLAY
1. Press A to change mode. Mode sequence is normal time, recall, alarm, and
countdown timer.
2. Press and hold A 3 seconds to toggle auto EL on/off.
3. Press B for EL.
4. Press C to toggle hourly chime on/off.
5. Press D to flash time zone 2. Press and hold D 3 seconds to toggle normal
time display/time zone 2.
NOTE: In any mode, press and hold C 3 seconds to change to
chronograph mode.
NOTE: At any point in any setting mode, press B to exit setting mode. Time
and Calendar Setting
6. In normal time display, press and hold B 3 seconds; hour will begin flashing.
7. Press C to increase digit; press D to decrease digit. Press and hold C or D
for fast increment/decrement.
8. Press A to set and advance to next setting value.
9. Repeat steps 2 and 3 through setting sequence. Setting sequence is: hour,
minute, second, year, month, date, 12/24-hour format, month/date or date/
month format.
10.Press B to exit setting mode.
11.To set Time Zone 2, press and hold D 3 seconds to change to Time Zone.
12.Then use steps 1-5 to set.
NOTE: Weekday is automatically updated upon exiting setting mode.
RECALL MODE
1. Press A to change to recall mode.
NOTE: If no data is stored, display will show NO DATA. If data is saved,
Module MLL-045
NORMAL TIME DISPLAY
1. At each hour, time will automatically display for 2 seconds.
2. Press B for time display and animation.
3. Press B again to toggle time/date mode.
4. When time or date is displayed, press and hold B for 3 seconds to toggle horizontal/vertical display.
TIME AND DATE SETTING
1. From time display, press and hold A; 12/24 hour format will begin flashing.
2. Press B to select 12/24 hour format.
3. Press A to set and advance to hour.
4. Press B to advance digit.
5. Press A to set and advance to next setting value.
Module QAA-006 / QAA-033
NORMAL TIME DISPLAY
1. Press A for EL.
2. Press B to change mode. Mode sequence is time, time zone 2, alarm, timer.
NOTE: In any setting mode, if no pusher is operated for 10 seconds, all changes
will be saved and the setting will automatically return to display mode.
TIME AND DATE SETTING
1. Press and hold A for 3 seconds to enter setting mode; 12/24-hour format
will begin flashing.
2. Press B to change 12/24-hour format.
3. Press A to set and advance to seconds.
4. Press B to reset seconds to zero.
5. Press A to set and advance to hour.
6. Press B to increase digits; press and hold B for fast advance.
7. Press A to set and advance to next setting value.
8. Setting sequence is 12/24-hour format, seconds, hour, minutes, year,
month, date.
9. Press A to exit setting mode.
NOTE: Weekday will automatically update upon exiting setting mode.
DZ7180
DZ7122
display will show the current set (1-9).
2. Press C to toggle through set data: total time, best time, average time,
and each lap (up to 100 laps).
3. Press D to display current set; press D again to scroll to next set.
4. Press and hold D 3 seconds to delete all stored data in the current set.
NOTE: At any point in recall displays, press A to exit and change to
alarm mode.
ALARM MODE
1. Press A to change to alarm mode.
2. Press C to toggle alarm on/off.
3. Press D to toggle alarm 1/alarm 2.
ALARM SETTING
1. In alarm mode, press and hold B 3 seconds; hour will begin flashing.
2. Press C to increase digit; press D to decrease digit. Press and hold C or
D for fast increment/decrement.
3. Press A to set and advance to next setting value.
4. Repeat steps 2 and 3 through setting sequence. Setting sequence is:
hour, minute, time zone 1/time zone 2. 5. Press B to exit setting mode.
NOTE: Alarm will sound for 20 seconds. Press any pusher to silence alarm.
COUNTDOWN TIMER
1. Press A to change to timer mode. Default setting is 5 minutes.
2. Press C to start timer; press D to stop the timer.
3. Press and hold D 3 seconds to clear the countdown and reset the timer.
6. Setting sequence is: 12/24 hour format, hour, minutes, date, month.
7. Press A to save and exit setting mode.
NOTE: In 12 hour format, a small dot will be shown in the upper left hand corner of the display to indicate p.m. time.
NOTE: If no pusher is operated for 7 seconds, settings will be saved and the display will return to normal time display.
PERSONAL MESSAGE SETTING
1. Press B to display time, press B again to display date, press and hold A; first letter of message will begin
flashing.
2. Press B to select character.
3. Press A to set and advance to the next character.
4. Repeat steps until desired message is complete. Please note there are only ten spaces available.
TIME ZONE 2
1. Press B to change to time zone 2.
2. Press and hold A for 3 seconds to enter setting mode; hour will begin
flashing.
3. Press B to increase digit; press and hold B for fast advance.
4. Press A to set and advance to minutes.
5. Press B to increase digit; press and hold B for fast advance.
6. Press A to exit setting mode.
ALARM MODE
1. Press B to change to alarm mode.
2. Press and hold B for 3 seconds to toggle alarm/chime on/off.
3. Alarm will sound for 10 seconds. Press any pusher to silence alarm.
ALARM SETTING
1. In alarm mode, press and hold A for 3 seconds to enter setting mode;
hour will begin flashing.
2. Press B to increase digit; press and hold B for fast advance.
3. Press A to set and advance to minute.
- 4 -
DIGITAL GUIDE
DZ7184
DZ7185
DZ7186
NOTE: Alarm will sound for 20 seconds when countdown reaches zero.
Press any pusher to silence alarm.
TIMER SETTING
1. In timer mode, press and hold B 3 seconds to enter setting mode;
hour will begin flashing.
2. Press C to increase digit; press D to decrease digit. Press and hold C
or D for fast increment/decrement.
3. Press A to set and advance to next setting value.
4. Repeat steps 2 and 3 through setting sequence. Setting sequence is:
hour, minute, seconds.
5. Press B to exit setting mode.
CHRONOGRAPH MODE
1. In any mode, press and hold C 3 seconds to change to
chronograph mode.
2. Press C to start the chronograph; press D to stop the chronograph.
3. Press and hold D 3 seconds to reset to zero.
LAP COUNTING
1. Press C while the chronograph is running for lap reading.
NOTE: If no other pusher is pressed after C is pressed, display will
automatically show total chronograph time after 5 seconds, then next
lap running time after another 5 seconds.
2. Press B to return to chronograph next lap (up to 100 laps).
3. Press D to stop chronograph.
4. Press and hold B 3 seconds to save set data, or press and hold
D 3 seconds to reset to zero.
DZ7092
DZ7189
DZ7190
4. Press B to increase digit; press and hold B for fast advance.
5. Press A to exit setting mode.
COUNTDOWN TIMER
1. Press B to change to timer mode.
2. Press A to start/stop the timer.
3. When timer reaches zero, alarm will sound for 15 seconds.
4. Press any pusher to silence alarm.
TIMER SETTING
1. Press and hold A for 3 seconds to enter setting mode; hour will
begin flashing.
2. Press B to increase digit; press and hold B for fast advance.
3. Press A to set and advance to next setting value.
4. Setting sequence is hour, minute, second.
5. Press A to exit setting mode.
B
C
A
D
A
B
Hide quick links:
Advertisement
