Table of Contents
Advertisement
Quick Links
Non-Cellular CuddeLink Home Quick Set-Up
A quick guide to setting up your Non-Cellular CuddeLink Home camera.
Certain menus may appear differently; this guide references set up of
cameras on version 8.3 firmware. *Any CuddeLink camera can be setup as a Home in a CuddeLink network*
Supplies Needed to Begin Set-Up
1. Required amount of batteries
2. Full-size SD card 2-32GB. We recommend the SanDisk brand
Getting Started
1. Set the Time - Press Mode key to Clock. This should show you the
clock. Use the Up/Down arrows to adjust hour setting. Press More
key to go to minute setting. Use the Up/Down arrows to change
the minute setting.
2. Set the Date - Press More key twice after setting time to move to
the date. Press the Up arrow to get to the month. Use the Up/Down arrows to change the month. Press More key to
move to the day. Use the Up/Down arrows to change the day. Press More key to move to the year. Use the Up/Down
Arrows to change the year.
Quick Set-Up - Link Menu
Press Mode key to Commands. Press More key to Link Menu and press the Up Arrow
twice to get into the menu.
The screen should show Link Mode. Use your up arrow to change to Home.
Press More key to move to Link Loc. Use the Up Arrow to change to 001.
Press More key to Link chan. Press the Up Arrow to get to the first set of digits. Use
the Up Arrow to choose a number 1-16. Press More key to get to the second set of
digits. Use the up arrow to choose a number 1-31. *This will be the same number for
all remotes connected to this home camera... Example 08-20*
Quick Set-Up - Settings
Press Mode key to Settings. The LCD Display will flash between Setup and the mode
the camera is in. The camera is default set to EZ Mode for quick Set-up. If you do not
see EZ Mode, use your Up Arrow to get to EZ Mode.
Press More key to Delay. The camera's default Delay is set to 15 seconds and the rec-
ommended setting for quick set-up. The Delay dictates how fast the camera will re-
load to take an image after it has already been triggered by heat/motion and taken an
image.
Quick Set-Up - ARM the camera
Press Mode key to ARM. The camera will begin countdown and ARM to take pictures.
920-347-3810
cuddeback.support@cuddeback.com
CuddeLink Home
Model 1385
www.cuddeback.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Cuddeback CuddeLink Home 1385
Summary of Contents for Cuddeback CuddeLink Home 1385
- Page 1 Quick Set-Up - ARM the camera CuddeLink Home Model 1385 Press Mode key to ARM. The camera will begin countdown and ARM to take pictures. 920-347-3810 cuddeback.support@cuddeback.com www.cuddeback.com...
- Page 2 If you are not getting a connection, verify you have all cameras on the same Link Chan and Firmware Version. *F/W Ver - Press Mode to Commands, More to F/W Ver. This should match on all cameras in a network* 920-347-3810 cuddeback.support@cuddeback.com www.cuddeback.com...
- Page 3 Delay dictates how fast the camera will reload to take an image after it has already been triggered by heat/motion and taken an image. Quick Set-Up - ARM the camera Press Mode key to ARM. The camera will begin countdown and ARM to take pictures. 920-347-3810 cuddeback.support@cuddeback.com www.cuddeback.com...
- Page 4 Use the Up/Down Arrows to change to lower rate if desired. Press More key to Cell Test. When you deploy the camera in the field, you will want to run this test. Press the Up Arrow twice to run the cell test. 920-347-3810 cuddeback.support@cuddeback.com www.cuddeback.com...
- Page 5 8.3 firmware. Cell Home - Recommended Settings The following explains the recommended settings for quick-set up of Cuddeback cameras. There are a few options under Commands that you can change, but we recommend leaving them set to default. Leaving them on default is the recommended option.
Need help?
Do you have a question about the CuddeLink Home 1385 and is the answer not in the manual?
Questions and answers