Summary of Contents for b4Adventure Slackers TREEZONE ADVENTURE THREE HOUSE
Page 1
Warning! Do not climb on the and tear before using. Contact of gravity inside the tree house outside of the tree house Slackers for any replacement parts b4Adventure • Denver Colorado 80216 • 1-844-834-4334 QUESTIONS? info@b4adventure.com • www.b4adventure.com - DC:072020...
Page 2
Adventure Tree House. Weight of any kind should never be applied to the outside of the tree house frame. • If worn or damaged parts are found, contact b4Adventure for replacement parts - Do not substitute with other, non-b4Adventure parts or failure resulting in injury could result.
CHOOSING THE SITE: SURFACES: Do not install home playground equipment over concrete, asphalt, packed earth, grass, carpet, or any other hard surface. A fall onto a hard surface can result in serious injury or death to the equipment user. Due to the variety of places that this product can be suspended, we must urge caution when attaching the Tree House to your tree.
Page 4
ASSEMBLY INSTRUCTIONS STEP 1: LAY OUT ALL PARTS T1-T2 WARNING! It is very important to use all washers and locking nuts when you are assembling this unit. This will prevent loosening over time. A-G. SCREWS, WASHERS & BOLTS H. TENT COVER M.
Page 5
STEP 2: ASSEMBLE THE FRAME AND TENT COVER YOU WILL NEED H. Tent Cover C. Screw I3. Bottom Frame I1. Base Frame Pole Corners I2. Back Base Frame Pole • NOTE: All of this is done on the ground • Metal square poles are for the bottom. Make sure that when you connect the corners and the tubes, that you line up the screw holes.
Page 6
STEP 3: ASSEMBLE WALLS AND TOP FRAME YOU WILL NEED H. Tent Cover K2. Front Top Pole C. Screw B. Bolt K4. Top Frame K3. Back Top Pole Corners G. Screw K5. Top Frame Corners J. Vertical Pole K1. Side Horizontal Poles •...
Page 7
STEP 4: ASSEMBLE CANOPY YOU WILL NEED L1. Canopy X1 L3. Medium Canopy Poles L4. Canopy Connectors X4 L2. Short Canopy Poles L4. Long Canopy Poles • 3.5 - Tent pole connector should face • Assemble the tent top. outward during assembly. •...
Page 8
STEP 5: INSTALL CENTER BRACKET AT DESIRED PLATFORM HEIGHT YOU WILL NEED • Bottom of treehouse can be installed anywhere between 4 ft (1.2 m) - 8 ft (2.4 m) high off the ground. • NEVER install the floor of the Tree Diameter Tree Diameter tree house higher than 8 ft (2.4 m) in the air.
Page 9
STEP 6: ATTACH THE HOUSE TO TREE • Lift up the tree house with one person on each side. Place the bottom of the frame into center bracket. Metal loops on the bottom should be on each side of the bracket. YOU WILL NEED Assembled House Assembled Center...
Page 10
STEP 8. INSTALL BASE BRACKETS YOU WILL NEED • Assemble the center strap into the base brackets. Slackers logo should be facing up. • It is very important that the support poles are pushing up the outer corners to create a flat floor for the tree house. •...
Page 11
STEP 9. INSTALL LADDER U3. Ladder Steps X6 YOU WILL NEED U2. Carribeaner U1. Verticle Webbing Staps X2 U5. Pegs X12 • The tree house ladder is 7 ft (2.4 m) long • If you install the floor of your tree house less than 8 ft (2.1 m) in the air, you can remove ladder steps to make the ladder shorter •...
Page 12
• You assume all risks and accept full responsibility for any injury (including death) or damages that may occur from its use. All the information provided by b4Adventure either printed, electronic or other, is not to be considered professional instruction or advice. Users of this equipment are encouraged to seek professional instruction regarding specific questions about usage, location, installation or other aspects of hanging swings.
Need help?
Do you have a question about the Slackers TREEZONE ADVENTURE THREE HOUSE and is the answer not in the manual?
Questions and answers