Rear Exit; Rear Exit Shield (For Rear Vent Only) - Napoleon Ascent B42NTR Installation And Operation Manual

22
3.11

rear exit

venting requirements
EN
2.10 rear exit
EN
FAILURE TO CREATE A SEAL TO THE FIREBOX WITH THE EXHAUST COLLAR ASSEMBLY WILL CAUSE
WARNING
!
THE APPLIANCE TO FUNCTION IMPROPERLY AND CAN CAUSE INJURY OR PROPERTY DAMAGE.
• Failure to create a seal to the firebox with the exhaust collar assembly will cause the appliance to function
improperly and can cause injury or property damage.
Remove the safety screen and glass front, refer to " SAFETY
A.
SCREEN / DOOR REMOVAL AND INSTALLATION" section.
Remove the safety barrier and glass front (see "safety barrier /
A.
Remove the contents from the firebox and set aside, you will
B.
door removal and installation" section).
need the exhaust flue collar from the top of the log carton.
Remove the contents from the firebox and set aside. You will
B.
To ease assembly, remove the four hex head screws securing
C.
need the exhaust flue collar from the top of the log carton.
the deflector from inside the top front of the firebox, refer to
To ease assembly, remove the four hex head screws securing
C. Figure 1.
the deflector from inside the top front of the firebox (Fig. 1).
Place the gasket (provided) over the 4" (102mm) flue collar assembly and
D.
Place the gasket (supplied) over the 4" (102mm) flue collar assembly and bend along
D. bend along perforation.
perforation.
From inside the firebox, insert the 4" (102mm) flue collar through the back
E.
From inside the firebox, insert the 4" (102mm) flue collar through the back of the
E. of the firebox. Install the rear exit shield onto the 4" (102mm) flue collar, see
firebox. Install the rear exit shield onto the 4" (102mm) flue collar (see "rear exit
"REAR EXIT SHIELD" section for installation instructions.
shield (for rear vent only)" section).
Secure the flue collar assembly, gasket and rear exit shield using the four
F.
Secure the flue collar assembly, gasket and rear exit shield using the four hex
F. hex head 3/8" thread cutting screws, refer to Figure 2. NOTE: Do not
head 3/8" thread cutting screws (Fig. 2).
overtighten. The gasket needs only to be snug against the firebox.
note:
Reattach the deflector using the four screws and install the log set, glass door
G.
and safety screen.
Do not overtighten. The gasket needs only to be snug against the firebox.
Reattach the deflector using the four screws and install the log set, glass door, and safety
G.
barrier.
3.12

rear exit shield (for rear vent only)

2.11 rear exit shield (for rear vent only)
Remove the safety barrier assembly and door from the appliance, refer to the "SAFETY SCREEN &
A.
Remove the safety barrier assembly and door from the appliance (see "safety barrier / door removal and
A.
DOOR REMOVAL / INSTALLATION" section of the manual for detailed instructions.
installation section").
Loosen the two screws, that secure the exhaust plate, and slide the baffle in place by sliding its
B.
Loosen the two screws that secure the exhaust plate, and slide the baffle in place by sliding its
B.
slotted openings behind the screwheads, tighten the two previously loosened screws. Refer to the
slotted openings behind the screwheads. Tighten the two previously loosened screws (Fig. 1).
illustration below.
Reinstall the door and safety barrier assembly on the appliance (see "safety barrier / door removal and
C.
Reinstall the door and safety barrier assembly on the appliance, refer to the "SAFETY SCREEN &
C.
installation" section).
DOOR REMOVAL / INSTALLATION" section of the manual for detailed instructions.
NOTE: THIS SHIELD IS USED TO BLOCK THE VIEW THROUGH THE VENTING TO THE OUTDOORS.
W415-1293 / F / 11.23.17
22
W415-1293 / G / 07.06.18
note:
This shield is used to block the view through the venting to the outdoors.
WARNING
!
Fig. 1
DEFLECTOR
DÉFLECTEUR
DEFLECTOR
DÉFLECTEUR
Fig. 2
Fig. 1
Fig. 1
Fig. 2